STM32CubeMX (MCUs)

cancel
Showing results for 
Search instead for 
Did you mean: 

Forum Posts

The CubeMX/CubeIDE login issue is resolved

Hello CubeMX/CubeIDE users.  From the time period of May 14 to May 17, 2024, some users have faced issues when connecting to the ST network while using CubeMX or CubeIDE.Some examples were issues downloading firmware packages using STM32CubeMX and ST...

STM32CubeMX 6.11.1 released

STM32CubeMX 6.11.1 was released on st.com as well as an in-tool update patch. Main issues fixed in this patch: Ticket 176645 : STM32CubeMX V6.11.0 has lost the "JTAG (5 pins)" debug mode for all the STM32H7 series but the STM32H7Rx/7Sx microcontrolle...

STM32CubeMX 6.11.0 released

We are pleased to announce you that the official release of STM32CubeMX V6.11.0 is available. What is new in STM32CubeMX V6.11.0? New MCUs series : STM32U0 (STM32U083xx/73xx/31xx), STM32H7RS (STM32H7R7xx/H7R3xx/H7S3xx/H7S7xx) and STM32H5 (STM32H533/H...

stm32h7 cubemx clock configuration Bug

Hi I have seen problems with stm32h7 cube uart bug.The Sources for uarts are pll2q but when debugging :It says pclk1 and pclk2 are configured.And even with these values baud rate will not be what I set. I have to divide  it by 2 (clock divider is 1)....

ArmanIlmak_0-1705149065099.png ArmanIlmak_1-1705149163333.png

Resolved! Error unknown nature on STM32Cube IDE after update

Hi all, how are you?. I'm making a project with an STM32F401VE and I've updated the IDE, after that there are about ten dependencies that says something related to inknown dependencies and the .ioc project doesn't opens. I read some over there and so...

VRami.1 by Associate III
  • 3683 Views
  • 40 replies
  • 7 kudos

Resolved! Is there a bug in STM32CubeMX about SDIOCLK?

STM32f103vet6It's in the manual that SDIO adapter clock (SDIOCLK = HCLK).  When HCLK is set to 72MHz, SDIO_CK is configured through the register SDIO_CLKCR bit 7:0(CLKDIV). When the bypass clock is not used, SDIO_CK=SDIOCLK/[CLKDIV+2], which should b...

XvSenfeng_3-1704782951218.png XvSenfeng_4-1704782976160.png XvSenfeng_6-1704783374909.png XvSenfeng_5-1704783155276.png

Resolved! how to configure adc in ethernet using nucleo-h745zi

Hello Team, Hello i have a Nucleo H745ZI_Q board in this Ethernet without RTOS is working fine but  when am going to configure ADC  all the three ADCs are shows error message --> Partly Disabled conflict with: ETH: mode RMII   even many channels also...

ggowd1_0-1704976431016.png
ggowd.1 by Associate III
  • 462 Views
  • 3 replies
  • 0 kudos

FR_DISK_ERROR always is returned by f_open.

Hi all.My team has been working on a project that contains a SD card based on Standard Library. Recently we've decided to migrate to HAL and it started.Fortunately, All part of our project were changed as well as possible to HAL and they're working g...

STM32G474RE ADC Clocking

Hiya!  I'm trying to figure out the clock config for my micro. I'm using ADC3 IN1 currently, and using the internal HSI clock source. Using the default settings, I can't seem to get anything better than 3.3 MSPS, and this is with a 10-Bit ADC resolut...

Jbin0101 by Associate II
  • 3509 Views
  • 4 replies
  • 1 kudos

Question about ADC versus GPIO Analog

Posted on April 03, 2015 at 04:23In STM32CubeMX, when I click on a pin, the following are two of the choices amongst others are presented to me. I want to understand what the difference is between ADC1_IN0 versus GPIO_Analog. I have looked through n...

Resolved! CubeMX SPI data size bug?

In CubeMX when configuring a SPI peripheral I can only choose either 8 or 16 bit, but the STM32G491 reference manual says data size can be from 4 to 16 bit. Is this a bug in CubeMX?(using the newest CubeMX version)

decalvus by Associate II
  • 386 Views
  • 4 replies
  • 0 kudos