Resolved! NUCLEO-C5A3ZG STM32C5 QSPI Display Bring up Project
This project tests the STM32C5's XSPI capability to drive QSPI display using the NUCLEO-C5A3ZG M.2/SerialMem connector. GitHub - stm32-hotspot/STM32C5-M2-Serial-Mem-QSPI-Display · GitHub
STM32 MCUs Boards and hardware tools
Ask questions and find answers on STM32 hardware set-ups, including schematic-related challenges, debugging probes, power configurations, and more.
Forum Posts
Resolved! STLink Dual Core programming
Hi,Can ST-Link be used to program both M0 and M4 cores? Also if the controller in STLink is replaced with STM32WB55RG can the driver for STLink be customized or does it require a new driver development? Is the driver open source? If yes, on what form...
Studying materials about hardware in the loop
Hi, Thank you for reading this question.I am using STM32F429 for hardware-in-the-loop (HIL) simulation. The emulator is OPAL-RT. However, I did not find any relevant information about HIL in ST community. Can anyone share some information or where ca...
Is it possible to configure eclipse to debug using the ST-Link v3 of the STM32G474-Nucleo board?
Good Morning,I am currently using a Nucleo -board stm32g474re, but I am unable to configure eclipse to connect to the Nucleo using the ST-Link v3.Is it possible to configure eclipse to debug using the ST-Link v3 of the Nucleo board?In the past with N...
Resolved! How to enable SWO with ST-Link Utility on STM32F407G-DISC1
I'm working with the STM32-base template for F4 located here:https://github.com/STM32-base/STM32-base-F4-templateTo compile with gcc toolchain and loading the binary with STLink Utility. The binaries work fine on the board, but I cannot figure out ho...
DMX demo for STM F1
Hello, I read in the following docs there is an official demo FW provided from ST for a DMX application on F103 MCU but I couldn't find it! Can someone help me to understand where I can download it?https://www.st.com/content/ccc/resource/sales_and_m...
ST-LINK v3 - eclipse
Hello.I bought this programmer: ST-LINK V3. I need it to debug my program in eclipse. I tried everything but the programmer doesn't work.Does anyone have a tutorial to debug with this programmer?programmer working with this appplication: STM32CubePro...
NUCLEO-H745 + ST-Link Utility = Can not connect to target
We tried our custom board that has STM32H745XI through ST-link V2 with updated firmware. Initially in boot mode the board connects and we were able to read flash. Then after some time the SWD connection is lost. It is not even able to debug the appli...
I have a hardware in which I am using the 144 pin STM32F407ZGT6 and it workings fine. I upgraded my MCU to STM32F767ZGT6 and I am not able to program the IC. Read protection is enabled and it is not getting removed.
The MCU is brand new. I have tried multiple hardware, multiple MCU ICs, multiple programmers. I have upgraded my programmer and also tried the STM32CubeProgrammer also. The MCU is not getting hot and current consumption is nominal. On the same hardwa...
I'm a complete newbie. If your goal was to learn about MCU operation in general and it was a requirement that you could display, on a PC, the contents of MCU registers, what ST products do you think would you buy?
I think I need some kind of evaluation board with ST-Link. Would it matter in your choice, if the design goal was to produce a WAV pl;ayer using an MCU?EDIT: Not sure whether I've chosen the right forum.
Programming error writing to OTP on STM32F412xx
I am trying to write to the OTP on a STM32F412xx using version v4.5.0.0 of ST-LINK but am getting "Error occured during memory writing!" (note bad spelling is not mine but ST's :-))The memory area for the OTP is 0x1FFF7800 and I can read it ok. I've ...
