Ask questions on STM32CubeProgrammer and find answers on device detection, connection failure, programming issues, and more.
We are pleased to announce that STM32CubeProgrammer 2.22 is available What is new in 2.22: Support for the STM32U3 microcontrollers with 2 Mbytes of flash memory: Internal memory programming through debug and bootloader interfacesOption bytes program...
Dear STM32CubeProgrammer Community, I hope you are all doing well. Over the past months, you may have received an email from me, either through the STM32CubeProgrammer survey or on other topics like CSAT or Raspberry Pi support. First, I would like...
Major change in SigningTool for STM32N6 in STM32CubeProgrammer v2.21.0 This release, we decided to change signing tool behavior to not automatically align the payload to 0x400 with padding bytes, since this is not necessary for other STM32 series. T...
Hi,I'm having trouble getting my ST-Link V2 dongle to be recognized by Cube Programmer. It is recognized by Windows 10 in the device manager, I have been able to update the firmware, and I can get it to load in STM32 ST-Link Utility, but that program...
Hi, I have brought 2 STlinkV3MODS. I have soldered wire at CN5 connector with 5+3 pin general connector to target the bluepill(not sure original or clone) the target MCU is STM32F103C8T6. when i select STlink at cube programmer shows error: debug aut...
Hello Everyone!STM32CubeIDE version: 1.19.0STM32CubeProgrammer version: 2.18.0MCU: NUCLEO-STM32U575ZI-QI tried to use USBX DFU to update the firmware on the STM32U575ZI. The DFU mode was detected by STM32CubeProgrammer. However, when I clicked the co...
Hello everyone,I’m currently facing a blocking issue with SWD programming on an STM32U575VIT6Q placed on a custom PCB.Until today everything worked correctly: I use a CLI-based flashing procedure that programs a set of binary files (around a dozen) u...
Launched STM32CubeProgrammer v2.20.0 after a long time since last use - it prompts an update available via an icon button.Clicked the icon, clicked Next, ticked a box, clicked "install Now", it starts download ing a big file...When the file has finis...
Hi,I'm trying to work with the STM32N6. I have a NUCLEO-N657X0-Q board.When I use an external debugger via CN1 everything is fine, however I am experiencing a lot of trouble with the ST-Link.It seems like there is a small (0.01%) chance that attempti...
Hi!I'm having trouble connecting to an STLINK ISOL via STM32CubeProgrammer. The STLINK is authentic, I purchased it from digikey. The programmer is detected under Device Manager. The programmer's LED remains static red at all times. Sometimes STM32Cu...
Good dayI have a Custom PCB with a STM32F217ZG populated.When trying to program with the STM32CubeIDE I get a No STM32 target found error.Then I tried with the STM32CubeProgrammer and get the following:20:27:26 : UR connection mode is defined with th...
Hi. This is a Linux problem, because with the same parameters it works on Windows. I tested with v2.21.0.I am trying to use the UART connection mode with these parameters:RTS: HighDTR: Negative pulseI can see, with a voltmeter, that the RTS/DTR signa...
Hi, I’m working with an STM32C011F6P6TR device, and after programming it via SWD using STM32CubeProgrammer, the MCU became completely stuck in resetSymptoms- After programming an ELF file through STCubeProgrammer, the MCU no longer runs.- The NRST pi...
