Power management

Discuss power management solutions. Ask questions and find answers on voltage configurations, short circuit protection, and programming.

cancel
Showing results for 
Search instead for 
Did you mean: 

Forum Posts

Wireless Charging solution Wiki

This Topic is used for Wireless Charging solution 1.Mcu C drive code: GitHub - STMicroelectronics/STWirelessCharging-C-Drivers: Standard C platform-independent drivers for wireless charging ICs    

willzhou_0-1717985741931.png
willzhou by ST Employee
  • 12425 Views
  • 22 replies
  • 30 kudos

L7981 Random Dropouts

Hi, I'm looking for technical help on an L7981 voltage regulator issue. We have been using these for years in various designs with minimal issue. On a recent new prototype, I am having an issue I have never seen before, where on occasion the regulato...

MGarr by Associate
  • 1175 Views
  • 3 replies
  • 0 kudos

How can I reduce L6472 Stepper Motor Noise due to harmonics?

I have a motor control PCB with x6 L6472PD stepper motor drivers on. 2 of the drivers are being used to drive NEMA17 "hybrid stepper" linear actuators that move a module along a linear guide. The two drive systems are laid out identically, and conven...

0693W00000Kb5kwQAB.png 0693W00000Kb7BeQAJ.png
LWalk.1 by Associate II
  • 1200 Views
  • 5 replies
  • 0 kudos

Measuring the frequency response of an optocoupler (e.g. PC817C) with different pull-up resistors using a Bode 100.

My test reference circuit is from Mr. Christophe Basso's book: "Designing Control Loops for Linear and Switching Power Supplies By A Tutorial Guide"The picture is showed as follow.Unfortunately, it may be a problem with my test circuit, or maybe the ...

0693W00000KbyHuQAJ.png

SRC0GS22D POWER RESET

I am trying to reset the power by controlling GPIO3.3V.However, the initial power is ON and OFF only, and there is no control thereafter. 

0693W00000KbkdwQAB.png
KSUWA.11 by Associate
  • 484 Views
  • 1 replies
  • 0 kudos

PM8800 PoE Issues (high ripples)

We designed board with PoE capability using ST PM8800 chip. We encountered some problems.Issue #1When our board is powered from external power supply (Vin(AUXII)=32V) we get output voltage with high ripples and PM8800 nPGD is inactive (High). Ripple ...

DRusi by Associate
  • 988 Views
  • 1 replies
  • 1 kudos

Resolved! Ihm08m1 change shunt

hi I have the ihm08m1 how can I change from 1 shunt to 3 shunt if by default it is soldered on 1 shunt?

SDall by Associate II
  • 1105 Views
  • 4 replies
  • 0 kudos

L6480 UVLO-Bit problem. Can't get it flip to 1.

Hello,I use the EVAL6480 Board and the STM32 F446RE as MCU to communicate to the driver.My Steppermotor [1] (not exactly this but very similar) has oer phase a resistance of 1,2 ohm.My Problem is that the motor does not turn because the UVLO flag is ...

_legacyfs_online_stmicro_images_0693W00000FDGk6.png
Evdsl.1 by Associate II
  • 1796 Views
  • 5 replies
  • 0 kudos

UVLO flag always on

Hi, Using IHM03A1, I'm driving a 48V-9A motor.According to @Cristiana SCARAMEL (Employee)​ recommandations, I add 15mOhm/3W resistances in parallel of R1 and R2, so R1 and R2 value is now 13mOhm, I choosed current mode, set run current to 10.2A (132....

BL1 by Associate II
  • 1316 Views
  • 4 replies
  • 0 kudos