Wireless Charging solution Wiki
This Topic is used for Wireless Charging solution 1.Mcu C drive code: GitHub - STMicroelectronics/STWirelessCharging-C-Drivers: Standard C platform-independent drivers for wireless charging ICs
Power management
Discuss power management solutions. Ask questions and find answers on voltage configurations, short circuit protection, and programming.
Forum Posts
Spice libs L4984D | STW62NM60N | STTH3006DPI
Posted on May 19, 2015 at 09:25Hi, i am not sure if this is the correct forum, but i am searching for the libraries for the following products: L4984D STW62NM60N STTH3006DPI Are there any .lib available for LTSpice or PSpice and can you please post ...
Understanding L9942 Stepper Motor Driver
Posted on May 08, 2015 at 07:15Dear All,Thank You for your great support as always..I have the following clarifications, Tried to set STALL threshold using the AN2650 procedure, when the STALL threshold value is 00000000 STALL is not set, but when...
Rogowski Coil using STPM01
Posted on April 29, 2015 at 14:06Hi, I am a student and i am trying to build a current sensing device using rogowski coil and STPM01. I am 'blind' to this project. I read on the datasheet that STPM01 can be used as a single chip monophase energy met...
problem with DfuSe tool
Posted on April 25, 2015 at 11:52HiI want to use to DfuSe tool for my application. I use L6470 stepper motor driver and STM32F107RC microcontroller in my board. My DfuSe tool is V3.0.4. I load firmware to the board by using the DfuSe demonstration s...
Why does L6480H driver register value reset to default
Posted on April 22, 2015 at 19:07The original post was too long to process during our migration. Please click on the attachment to read the original post.
L6480H driver stall detection and overcurrent detection
Posted on April 16, 2015 at 16:16In application note AN4355, overcurrent detection page 18 and stall detection page 21, application note writes two equationsEquation 1: IOCDth = VOCDth � Rds(ON)Equation 2: ISTALLth = VSTALLth � Rds(ON)Why current is...
drive brushless DC motor with L6235 according to DT0001
Posted on April 10, 2015 at 11:52Hi there, I recently had a discussion on DT0001 motor control [DEAD LINK /public/STe2ecommunities/motordriver_ics/Lists/Motor%20Control%20Firmware%20and%20Software/Flat.aspx?RootFolder=/public/STe2ecommunities/motord...
VNH3SP30-E overheating issue
Posted on April 22, 2015 at 18:22Hello all, I am having a bit of trouble with the VNH3SP30-E overheating. the part should be capable of supplying 30Amps continuously however when I supply 20 amps the chip overheats and shuts down after around 10 sec...
L9942 Driver IC SPI Programming
Posted on April 01, 2015 at 12:58Dear Experts,I am new to L9942 Driver IC.I am currently working on this IC for a stepper motor control in automotive safety application.I have attached a 'c' program written for SPI communication with L9942. The cont...
bugs and crash of V 2.2 SPINfamily GUI
Posted on April 09, 2015 at 21:02The new version (V2.2 stsw-spin002.zip) has a much improved setting of motor paramaters, and it now works on XP but the GUI still crashes badly so motors cannot be tested. # GUI crashes hard in both XP and Win 7, in...
