Power management

Discuss power management solutions. Ask questions and find answers on voltage configurations, short circuit protection, and programming.

cancel
Showing results for 
Search instead for 
Did you mean: 

Forum Posts

Wireless Charging solution Wiki

This Topic is used for Wireless Charging solution 1.Mcu C drive code: GitHub - STMicroelectronics/STWirelessCharging-C-Drivers: Standard C platform-independent drivers for wireless charging ICs    

willzhou_0-1717985741931.png
willzhou by ST Employee
  • 9301 Views
  • 19 replies
  • 18 kudos

Questions about VNB35N07TR-E device

Dear ST Team, I hope this message finds you well.I am currently working on a new design project for [mention the application or product type if applicable] where we are considering the VNB35N07TR-E component. I have several questions regarding this c...

Nazmul by Associate
  • 334 Views
  • 1 replies
  • 0 kudos

TC4469COE713 multi output error

Hello, I purchased this IC and would like to use it to alternately control four different inputs so that the IC’s four outputs can switch sequentially. However, I'm currently facing an issue: I’m only providing input to a single channel, e.g., Ain, b...

Leon_show_0-1730914807432.png

Resolved! LDL212

LDL212-3.3v DFN (2x2) Running Superhot  With LDL212Heat Dissipation (Power Dissipation)The power dissipation PP can be calculated using the formula:P=(VIN−VOUT)×IOUTP = (V_{IN} - V_{OUT}) \times I_{OUT}Where:VINV_{IN} = 6.65V (input voltage)VOUTV_{OU...

USB PD Load Sharing

Hello, we are searching for a USB PD Power Budgeting/ Load Sharing solution. Here an example: Lets say we have 4 USBC PD Ports. All in all they sould be able to source 60W. One port is sourcing 15V/3A=45W, then the remaining 4 should just be able to ...

VH by Associate
  • 422 Views
  • 1 replies
  • 1 kudos

Resolved! Voltage regulator to give 2.5V out from 3.3V in

I am designing an interface board where there is an ADC that needs two different power supplies (3.3V and 2.5V). To minimize this board, instead of bringing the two power supplies from outside, I would like to bring only the 3.3V one and through a vo...

Resolved! Calculate stepss for PowerSTEP01 (and L6480)

Hi, I am currently implementing software/firmware for the PowerSTEP01 chip and discovered a inconsistency in data sheet https://www.st.com/resource/en/datasheet/powerstep01.pdf. For parameter INT_SPEED (section 11.1.11 in datasheet) the equation does...

0690X000009k1YHQAY.jpg

Resolved! STSPIN32F0 Overcurrent detection R43 value

According to the reference circuit, R43 is 75kohm.Also UM2154 User manual said that R43 should be higher than 30kohm.What happens if R43 is 22kohm. Is overcurrent detected by STSPIN32F0?

0693W00000QMwylQAD.png
TYama.17 by Associate II
  • 2074 Views
  • 9 replies
  • 0 kudos

Diode IFSM estimation

HelloI need to estimate IFSM for certain current pulse.Does anyone know how to do it?I found this app note :Schottky diode avalanche performance in automotive applications (st.com)But it is not clear the method as intervals are weird :I ^4 x t = Cste...

Fausto2 by Associate II
  • 1156 Views
  • 3 replies
  • 0 kudos