Power management

Discuss power management solutions. Ask questions and find answers on voltage configurations, short circuit protection, and programming.

cancel
Showing results for 
Search instead for 
Did you mean: 

Forum Posts

Wireless Charging solution Wiki

This Topic is used for Wireless Charging solution 1.Mcu C drive code: GitHub - STMicroelectronics/STWirelessCharging-C-Drivers: Standard C platform-independent drivers for wireless charging ICs    

willzhou_0-1717985741931.png
willzhou by ST Employee
  • 9314 Views
  • 19 replies
  • 18 kudos

smps parallel connection

Posted on July 19, 2017 at 12:15Hello. i design L6566BH on design süite. But i see that max power out is 350w. if i do same smps 3 pieces and i want to get 1050w can i connect their outputs in parallel connection? because i see that it is not basic...

powerstep01 with high voltage design

Posted on July 17, 2017 at 11:41I'm using http://www.st.com/content/st_com/en/products/ecosystems/stm32-open-development-environment/stm32-nucleo-expansion-boards/stm32-ode-move-actuate-hw/x-nucleo-ihm03a1.html to evaluate the powerstep01 chip, and ...

Resolved! L6480 Abnormal over current detection behaviour

Posted on April 10, 2017 at 09:44HiAbnormal over current detection behaviour on stepper motor controller L6480. After initialization a hard stop command is given to hold the stepper motor, which seems to work just fine, all the expected waveforms ap...

Surge Test Failure

Posted on July 13, 2017 at 06:50Dear Team,Please find the attached design. ehg7520_cpu_ board.pdf In my product design i have used TVS diodes and ORing diodes from ST Micro electronics. My product has to under go the following test. TEST_Cases.xls ....

STM32 PMSM FOC Software MC library:What is the impact of calling TSK_SafetyTask() at 1ms interval, instead of 0.5ms as recommended in User Manual?

Posted on July 12, 2017 at 12:23I'm using STM32 PMSM FOC Software MC library to run my motor. I use the MC API to interact with my own code and it seems to work fine - motor can run.However, mentioned in the User Manual (UM1052, section 10.3, Table ...

Boost LED Driver

Posted on July 03, 2017 at 12:13We are using LED6001 LED Driver in a Flasher.The problem is when the input is less than 10.5V it works O.K but when the input is more than 10.5V the LED current reduces to almost 10mA or shuts down. The Problem is sam...

ammar by Associate
  • 627 Views
  • 1 replies
  • 0 kudos

X-NUCLEO-IHM03A1 Arduino compatibility?

Posted on October 25, 2016 at 13:37Hello,I'm trying to use an Arduino UNO R3 to control the IHM03A1 stepper driver.  I found an Arduino library for the IHM01A1, which looks to me like an older version of the stepper driver.  I installed the library ...

Powerstep noise

Posted on July 10, 2017 at 17:33Hi, i'm trying the powerstep board, with 1/16 step using advance current control, when the motor run there's no problem. But when the motor is stopped there's a little noise from the motor. The noise is greather when ...

Triac T1635-700G-TR

Posted on June 16, 2017 at 06:46 I'm making about Triacs T1635-700G-TR to control motor, light. But I dont know detail about it. What is this IC integrated? I really need circuit about Using this IC. I'm read datasheet about this IC. But dont have c...