Power management

cancel
Showing results for 
Search instead for 
Did you mean: 

Forum Posts

Wireless Charging solution Wiki

This Topic is used for Wireless Charging solution 1.Mcu C drive code: GitHub - STMicroelectronics/STWirelessCharging-C-Drivers: Standard C platform-independent drivers for wireless charging ICs 2. Python drive code, check attach file "Python_FT260_S...

willzhou_0-1717985741931.png willzhou_1-1734156149269.png willzhou_0-1734155900141.png
willzhou by ST Employee
  • 6457 Views
  • 15 replies
  • 10 kudos

SPV1040 Light Load Efficiency

What is the SPV1040 MPPT Charger's light load efficiency? In my application, the power from the Solar Panel goes down to 10mW. So, I'm interested, to know the output of SPV1040T when the input power is only several mW.  From the datasheet, my applica...

Stalin_0-1725703826682.png
Stalin by Associate III
  • 298 Views
  • 2 replies
  • 0 kudos

SPV1050 No Voltage at the LDO-Out Pins

Hi all,I connected my SPV1050 chip as you can see in the picture and started to measure my circuit. It looks pretty good. I powered it up with 3.3V at IN_LV. And I can measure a voltage of about 2.416V at the STORE pin. And even the LDO2_EN pin got a...

SPV1050.png

About VNL5030JTR-E,VNL5050S5TR-E,VNLD5160TR-E

Thank you for your help.What V/μs is the maximum allowable value of dV/dt for the following components?Please let me know. VNL5030JTR-EVNL5050S5TR-EVNLD5160TR-E Thank you for your cooperation. Yukio IchikataiNIKKI CO.,LTD.

Ichi by Associate
  • 214 Views
  • 0 replies
  • 0 kudos

Resolved! Need of ROHS compliance document

We need ROHS compliance documents for (STM811SW16F, ESDA25W5, TSC214ICT) these part numbers, can you please share the document for further use.

Brindha by Associate
  • 479 Views
  • 2 replies
  • 0 kudos

STNS01 not shutting down properly

Hello, I have a simple circuit with an STNS01 charging a 150mAh single cell battery and am using the LDO to power an STM32F042 and a couple of other small devices. It mostly seems to work OK, however if I pull the SD line high using the micro (or an ...

Resolved! Viper319 Not performing for load more than 4W

I have attached the Actual Circuit as image. We have gone for flybuck topoogy.Input VBus = 335VDC. We require 15VDC, 600mA for Load Requirements. (9W Least Requirement)As per datasheet VIPER319HDTR is capable of delivering 19W. We designed the PCB Bo...

Rajesh_J by Associate
  • 714 Views
  • 1 replies
  • 0 kudos

Issue with STC3117 Fuel Gauge Resetting Repeatedly

 Hi,I am using the STC3117 fuel gauge, but my IC keeps resetting repeatedly, so I am not getting any voltage or current readings. However, I am getting the correct values for other registers, such as the device ID and temperature.I tried to debug thi...

tarang by Associate
  • 224 Views
  • 0 replies
  • 0 kudos

L4986A

I am using Simlis to carry out a simulation of AN5797 1KW bridgeless CCM-PFC pre-regulator based on the L4986A IC, I have built up the circuit, but it does not simulate and produces an error The voltage and currents of this circuit cannot be uniquely...