We are pleased to announce to you that the release 1.17.0 of STM32CubeIDE is available. What is new in 1.17.0: Microcontrollers, microprocessors, and board lists aligned with STM32CubeMX: Added the support for the STM32N6 seriesAdded the support for ...
We are pleased to announce to you that the release 6.13.0 of STM32CubeMX is available. What is new in 6.13.0: Added support for the following series, microcontrollers and microprocessors: STM32N6, STM32U3, STM32WL3x, STM32G411xx and STM32C0Added the ...
STM32CubeProgrammer v2.18.0 release information New features: Added the support for the STM32N6 series– OTP programming– External memory programming– Serial boot via USB/UART– FSBL signature with stm32header V2.3 through the signing tool• Added the ...
Hi there, I want to flash a HEX file using a Raspberry PI. So I followed the steps described here.But if I run this line:$> ./SetupSTM32CubeProgrammer-2.13.0.linuxI get the message:bash: ./SetupSTM32CubeProgrammer-2.13.0.linux: cannot execute binary ...
"Does this mean that I can only use the other three options exclude 'free' in either M4 or A7 and cannot switch between them?"
When debugging my firmware using STM32CubeIDE, the debugger seems to miss the start of the program. As an example, when I put breakpoints right at the top of main(), they are ignored. It's not only a couple of lines that are affected, but pretty much...
hello.Now I am using stm32mp157a-ev1 board and coding M4 program on stm32cubeide.However, there is a problem that the stm32cubeide stops at 70% after starting to run or debug.And can check the log for errors in metadata.2023-04-04 17:11:23,560 [INFO]...
Hi,I am using STM32CubeProgrammer version 2.12 running on Windows 10 to connect to the STM32MP157F-DK2 board ST-LINK connector CN-11.I managed to connect and when I click "Firmware upgrade" the STLinkUpgrade 3.4.0 window opens.However, when I press "...
Hello , This question belongs more to IAR community but still asking it .I was checking this project of OpenAMP : STM32Cube\Repository\STM32Cube_FW_MP1_V1.6.0\Projects\STM32MP157C-DK2\Applications\OpenAMP\OpenAMP_TTY_echo\STM32CubeIDE\CM4\DebugIt has...
I've been trying for hours to read an analog value from a pin and write it over UART with no success on my STM32MP1. I've assigned PF14 to ADC2_INN2 and set IN2 to "IN2 Differential", then I generate the code and when I try to build I get a bunch of ...
Hi,We are trying to replace UART8 instead of UART4 in uboot and UART8 doesn't work for us.We change to UART3 it work just fine.When we open STM32CubeMX, hopefully we can find something, but seem the application doesn't allow us to select UART8.Anyone...
Hi its me again,I'm told that i need to use SX1280 Transceiver with a STM32MP157A-DK1 (using ARM Cortex A-7 coding in C/C++) for SPI connection, im gonna take that SPI data and save it into a .txt file. Saving it into txt file is the easy, right now ...
Hello,We are using STM32MP157A.We are working on IPCC from A7-0,A7-1 to M4.We are getting IPCC interrupt A7-1 to M4,But when we are not getting interrupt from A7-0 to M4.In cubeMx it is showing NVIC to IPCC RX1 and TX1, but not showing to RX0,TX0.we ...
