STM32CubeIDE (MPUs)

How to use SX1280 Transceiver with STM32MP157A-DK1for SPI Connection and Data Transmitting/Receiving?

Hi its me again,I'm told that i need to use SX1280 Transceiver with a STM32MP157A-DK1 (using ARM Cortex A-7 coding in C/C++) for SPI connection, im gonna take that SPI data and save it into a .txt file. Saving it into txt file is the easy, right now ...

Even though I uploaded a new device tree using stm32cudeide, there was no effect on my pins.

I am generating device tree and compiled it by stm32cudeide and upload to my board. So, baiscally I am following this link:https://wiki.st.com/stm32mpu/wiki/How_to_manage_OpenSTLinux_projects_in_STM32CubeIDEMy issue is that no matter what I do, nothi...

STM32CubeIDE Serial Console in use

I am stuck at step 6 inhttps://wiki.st.com/stm32mpu/wiki/Getting_started/STM32MP1_boards/STM32MP157C-DK2/Develop_on_Arm%C2%AE_Cortex%C2%AE-M4/Modify,_rebuild_and_reload_a_firmwareMPU Serial Console is operational, ethernet RJ45 also, and serial port ...

Good afternoon. Using CubeMX, I created an empty project for the STM32MP157A-DK1 board. It compiles without errors. But when I try to start debugging in engineering mode, I get a message that there are too many breakpoints. When I try to start debugging i

Good afternoon. Using CubeMX, I created an empty project for the STM32MP157A-DK1 board. It compiles without errors. But when I try to start debugging in engineering mode, I get a message that there are too many breakpoints. When I try to start debugg...

How can i enable SPI5 on STM32MP157-DK1

Hi,Im working with STM32MP157A-DK1 board. Im working on the linux side, need to write C/C++ code for saving data into a SD card. I need to use SPI to get data from RF transceiver. I built linux and kernel as in this link:https://wiki.st.com/stm32mpu/...

Resolved! STMCubeIDE Activation DeviceTree Failed with STM32MP157A-DK1 ARM Cortex-A7

Hi, i just started working/learning STM cards as an intern. I want to run C/C++ codes on STM32MP157A-DK1 ARM Cortex-A7.I did the getting started tutorials at wiki, and im using environmet version 2.1.0 release I followed these posts:https://community...

How to wirte data into sd card with using DMA ( STM32MP157A-DK1 )

Hi,Im pretty new here, to be exact it is 2 weeks that i started learning/working with STM32MP157A-DK1, i did all the getting started tutorials on the wiki, now im looking at the CubeIDE, i dont know where to go.Basically i want to learn about writing...

Resolved! Cube IDE debug doesn't work on stm32mp157a-DK1

Hi,I'm having an issue while trying to debug the OpenAMP_TTY_ECHO_CM4 example described in gettin' started guide for stm32mp157a-DK1 (here link) using Cude IDE 1.4.2 on windows 10 machine. I configure the debug session as describe in the guide sectio...

Resolved! How to generate stm32mp157c-dk2.dts with stm32cubeide?

Hi,I used the STM32CubeIde version 1.4.Below is the procedure create "stm32mp157c-dk2.dts ":1) onpen STM32CubeIde2) Click "File->New->STM32 Project" to create a project "stm32mp157c-dk2"3)Click "Board Selector" to select board "STM32MP157C-DK2"4)Conf...

Cannot open ssh connection, "Inet address 192.168.7.2 is not reachable"

Hi everyone,I am trying to program CM4 proc using STM32CubeIDE (on Windows), i was following this tutorial:https://wiki.st.com/stm32mpu/wiki/Getting_started/STM32MP1_boards/STM32MP157C-DK2/Develop_on_Arm%C2%AE_Cortex%C2%AE-M4/Modify,_rebuild_and_relo...