We are pleased to announce that the minor version 6.14.1 of STM32CubeMX is available. What is new in 6.14.1: SAI settings not displayed in the configuration tab of STM32H7Bxxx devices: After upgrading to STM32CubeMX 6.14.0, the SAI tab configuration ...
We are pleased to announce that the minor release 1.18.1 of STM32CubeIDE is available. What is new in 1.18.1: This minor release will not bring any major updates to the STM32CubeIDE 1.18.1. It will be aligned with the STM32CubeMX 6.14.1. Main fixed i...
We are pleased to announce that the release 6.14.0 of STM32CubeMX is available. What is new in 6.14.0: Added the support for the STM32WBA6xxx microcontrollers and:Added the support for USBX multi-instanceAdded the support for the memory management to...
We are pleased to announce that the release 1.18.0 of STM32CubeIDE is available. What is new in 1.18.0: Microcontrollers, microprocessors, and board lists aligned with STM32CubeMX 6.14.0: Added the support for STM32WBA6xxx microcontrollers in the STM...
We are pleased to announce that STM32CubeProgrammer 2.19 is available What is new in 2.19: Support for the STM32WBA6xxx microcontrollers: Internal memory programmingOption byte/OTP programmingRDP regression with passwordSFI support Support for MCE N...
Hello Team,unable to download OpenSTLinux BSP package a tarball file named en.SOURCES-stm32mp2-openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06.tar.gz from the link (https://www.st.com/en/embedded-software/stm32mp2dev.html#get-software). Instead of BSP...
Hello,I’m unable to create a new project for the STM32MP2 (STM32MP251CAL3) in STM32CubeMX (Version 6.14.1). After selecting the MPU and clicking Start Project, I choose the TrustZone feature—but nothing happens. I can see a “*” appear next to “Untitl...
Hello everyone,I am new to STM32 architecture and configuration. I am trying to configure new GPIO ports and pins in an STM32H745i-DISCO board. I had some previous code for the pin configuration, but I could not 100% map it to the user manual for the...
Hello.I was glad to hear that the TouchGFX supportance have covered the STM32MP135F-DK. Even though it only support TouchGFX 4.24.0 and STM32CubeIDE 1.15.0 (I'm unable to download the IDE 1.15.0 ! Only 1.15.1 so I tried the 1.15.1).Right from the sta...
Hello all,I'm new with STM32MP157F-Disco board. So maybe i do something wrong, but i cant find a solution. I use CubeIDE_1.18.0 with packages STM32Cube_FW_MP1_V1.7.0. When i start a new project with the board selector, STM32MP157FAC1. Then it will ...
I'm trying to setup CubeIDE for STM32MP1 but cannot make it to see the OpenSTLinux SDK.Following this article:https://wiki.st.com/stm32mpu/wiki/How_to_install_the_Yocto_Project_SDK_in_STM32CubeIDEThe popup window that should allow to download the SDK...
I was trying to write a small firmware to keep the LD9 Orange LED steady ON, instead of blinking in STM32CubeIDE. I could able to flash into CM33 core using the debugger and able to debug. When I disconnect debugger, it still remain ON.But once I res...
We are pleased to announce that the minor release 1.18.1 of STM32CubeIDE is available. What is new in 1.18.1: This minor release will not bring any major updates to the STM32CubeIDE 1.18.1. It will be aligned with the STM32CubeMX 6.14.1. Main fixed i...
HiI am trying to program the Cortex M33 of STM32MP257F-DK dev board using CubeIDE. I have generated the code in Cube IDE. The debugger failing to program as the board not responding.Following are my debug settings:Again I tried using STM32 Cube Progr...
I'm following this guide https://wiki.st.com/stm32mpu/wiki/STM32MPU_Developer_Package and I'm stuck at 5.2.3. Building and deploying the Linux kernel for the first time. I followed all ST recommendations for directories names and structures, so every...