Automotive MCUs

Resolved! StellarStudio 7.1.0 officially pushed (Compliant for Java21 and eclipse 202409)

For your information , StellarStudio 7.1.0-JOURNEY version is officially pushed (for SR5x). (Windows , Macos, Linux) based on eclipse 202409 and the version CDT 202409 with standalone tools (Java 21) https://www.st.com/en/development-tools/stellarstu...

Resolved! How to install your Root Certificate in StellarStudio JRE

When installing some StellarStudio plugins http://*.srxstudio.org , you can meet the issue : sun.security.validator.ValidatorException: PKIX path building failed It is typical IT Issue :face_screaming_in_fear: in each corporate company. “"Path bui...

StellarStudio SR5E1 support is open to the mass market !

Dear all, We are thrilled to announce that as of today, March 1st, 2024, SR5E1 device support in StellarStudio is available to the mass market ! This means that any user can effortlessly download the official StellarStudio installation packag...

SPC58XXADPT100S Hardware User Manual and Schematics

Hello,Could someone from ST side provide these two documents for the SPC58XXXADP100S minimodule? I have only the documents for 64 Pins and found there are some small hardware differences for the 100S. (Some Jumpers which are not mentioned in the doc...

Resolved! I am working in a design project which uses SPC563M64L5. I have a Cyclone MAX Programmer (from PEMICRO) and I have to program the MCU with this device. I appreciate if you help me how can I set up the Cyclone MAX to be able to use it. Thank you very much

SPC5 and using SPC572L we have problem with DPLL channel 16 - SPC5_GTM_DPLL_ACTION_ID_15 not working

Our SPC572L application are using both MCS1 & MCS2 connected to DPLL and ATOM it works well on all 16 channels except the last one: channel 16 "SPC5_GTM_DPLL_ACTION_ID_15" if we change to ch17 "SPC5_GTM_DPLL_ACTION_ID_16" it runns fine but we need to...

SPC572L complex ATOM output for direct injection

We have the basic structure up and running for our project with trigger signal input correct decoded and output timed correct throught MCS to the ATOM channels.ATOM outputs are now timed pulses of the right duration and position, but we would need to...

Resolved! Is there any example code and debug software for STA1385?

Hi, I found there is nothing about how to develop on STA1385, even if there is no data sheet about thish chip. Could anyone tell me how to develop on this chip?Thank you

Resolved! SIUL unit setting up

I want to implement the GPIO unit in the SPC560P50L5 microcontroller with the SPC5STUDIO IDE. Please advise me how to configure the SIUL unit and registers? Or give me an example of SIUL unit setting up in the SPC560P50L5 microcontroller.(I actually ...

Resolved! SPC563M64L5 and SPC560P50L5 microcontrollers pin compatible

Are the SPC563M64L5 and SPC560P50L5 microcontrollers pin compatible?I mean, can two microcontrollers be assembled instead of each other?

Resolved! Hello, I'm trying to transmit and receive via DMA UART on SPC58EC-DISP. On the other side there is a STM32L432KC: the SPC transmit to STM32 which receives the message, but the message transmitted to SPC by the STM32 is not received. I post the code

#include "components.h"#include "serial_lld_cfg.h"void sddmatxcb(SerialDriver *sdp) { (void)sdp; pal_lld_togglepad(PORT_F, PF_LED2);}void sddmarxcb(SerialDriver *sdp) { (void)sdp; pal_lld_togglepad(PORT_F, PF_LED1);}/* * Application entry point. */in...

Is there anyone can r/w value to dFlash unit?

Hello, I followed the instructions on datasheet but I could not write and read any data.

Resolved! Hi, I am considering SPC58EC70E3F000X microcontroller in a design. 1. Can RTL8201F ethernet PHY from Realtek be used with SPC58EC70E3F000X microcontroller? 3. Does SPC58ECx/SPC584Cx has necessary libraries for Realtek Ethernet PHY ICs.

Automotive MCUs

Forum Posts