Solved

Hello,(ST-LINK + CubeProgrammer UART/USB both failing)I am using a NUCLEO-N657X0-Q board. I cannot flashing my code via the ST-Link ( ST-Link windows driver is installed and detected through device manager and I had already updated the stlink). it throws this error:STMicroelectronics ST-LINK GDB server. Version 7.11.0Copyright (c) 2025, STMicroelectronics. All rights reserved. Starting server with the following options:Persistent Mode : DisabledLogging Level : 1Listen Port Number : 61234Status Refresh Delay : 15sVerbose Mode : DisabledSWD Debug : EnabledInitWhile : Enabled Target unknown error 32 Error in initializing ST-LINK device.Reason: Unknown. Please check power and cabling to target.Then tried with CubeProgrammer to connect via STlink but it connects then quickly drops , here is the log :17:22:24 : STM32CubeProgrammer API v2.20.0 | Windows-64Bits17:22:39 : UR connection mode is defined with the HWrst reset mode17:22:40 : UR connection mode is defined with the HWrs

in debugging mode the values of variables gets corrupted when I check in live expressions. Here corrupted means shows wrong values.

When I compile my code, I get strange errors that make no sense.#define ADC_BUFFER 1000 gives error "expected declaration specifiers or '...' before numeric constant"even though the line above it #define ADC_HIGH_THRESHOLD 3500 doesn't generate an error.HAL_TIM_Base_Start(&htim3); and HAL_ADC_Start_DMA(&hadc1, (uint32_t*)adc_buffer, ADC_BUFFER); both generate "Syntax error".The TIM and ADC Start errors expanded error message is:  error: expected declaration specifiers or '...' before '&' token /* USER CODE END Header *//* Includes ------------------------------------------------------------------*/#include "main.h"/* Private includes ----------------------------------------------------------*//* USER CODE BEGIN Includes */#include <stdlib.h>#include <stdio.h>#include <stdbool.h>#include <stdint.h>#include <inttypes.h>#include "globals.h"/* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*//

I’m creating a project for NUCLEO-144 (STM32H563ZIT6)and I’m using STM32CubeIDE for Build/Debug.After reading various guides from the Web, I have still notbeen able to see any Console output (trying to use printf()and re-directing the character output with this: int _write(int file, char *ptr, int len){     for (int i = 0; i < len; i++)     {          ITM_SendChar((*ptr++));     }     return len;} Is there an esoteric Config in the IDE that I need to Enable (or Disable)?Have I missed some important item in the Project Creation? (I had used STM32CubeMX)Guidance appreciated!Paul++ 

Hello,while testing 6 types of SPI NAND with MP257, I found no 1V8 part boots (tested 2, MT29F4G01ABB and AS5F18G04SND). While looking at scope traces, 32MHz clock from BootROM is almost sinusoidal.I tested booting from Engineering mode and custom BL, it boots Linux as 21MHz but not at 32MHz. IOSPEED is set to “2” (tested 3 too).Then I set bit 14 in OTP 124 (allow for <2.5V for VDDIO3) and then set PWR->CR1 VDDIO3VRSEL too. Now, it boots with 32MHz from my BL (with IOSPEED 2) and clock now seems much nicer.But BootROM seems to ignore OTP 124 and tries to use 32MHz with 1V8 and GPIO in degraded mode.Is there way to make 1V8 OSPI boot work ? Force ROM to either use slower clock or to set VDDIO3VRSEL.Thanks, Martin

Hi everyone,I'm working on a project using NASA's Core Flight System (cFS) running over RTEMS RTOS, and I need approximately 8MB or more of external RAM for the workspace/heap.Currently, I'm using a NUCLEO-H753ZI board (STM32H753ZI), which only has 1MB of internal SRAM. I've been looking for an easy way to add external RAM, but I'm running into some challenges.My questions: Is there an easy way to add 8MB+ of external RAM to the NUCLEO-H753ZI? I've looked into FMC-based SDRAM shields/expansion boards, but I haven't found any off-the-shelf solutions that work well with this board. Is there a shield, module, or expansion board I should know about? If adding RAM to this board is not practical, which STM32 board would you recommend instead? I need: 8MB+ RAM, Cortex-M7 (or similar performance), and preferably existing RTEMS/cFS support. I've seen mentions of STM32H745I-DISCO or STM32H747I-DISCO having onboard SDRAM, but I'd like community input on the best choice. My sta

Hello,I am currently trying to leverage STM32H753 FMC feature to interface with legacy Motorola flexbus style peripheral.I suspect the answer to my question is no but I could not find an explicit statement within documentation saying it is precluded hardware wise :Is there a mode / configuration (down to the registers level) that could allow the write enable signal (WE) to be asserted before the chip select signal (NE) ?Thanks

I’m using SPC58EC80E5 and i wanted to load the files into unit without using JTAG, so that i wanted a Bootloader, How to work on that and if any sample projects are there for reference ? I already searched for this project “SPC582Bxx_RLA Bootloader Test Application for Discovery” it was no there.In fields i should load the project without using JTAG , i have only connection with CAN.

Hello, few days ago ST MCU FINDER PC v 6.1.0 stop downloading updates with error message:It's only me, or server problem? Thank you. Regards,Slavomir Tomascik

STM32CubeMX generates incorrect linker script for BKPRAM (Backup RAM) via Memory Management ToolEnvironmentSTM32CubeMX: v6.17.0, see "Memory Management" (Tools > Memory Management) MCU: STM32H523RETx Toolchain: STM32CubeIDE - GNU Tools for STM32 (14.3.rel1)Applied Memory Setup (screenshot):STM32CubeMX generates 3 linker scripts (STM32H523RETX_FLASH.ld, STM32H523RETX_FLASH_MMT_TEMPLATE.ld, STM32H523RETX_RAM.ld). The STM32H523RETX_FLASH_MMT_TEMPLATE.ld is used in the generated STM32CubeIDE project output. Issue 1: BKPRAM memory region has incorrect x (execute) permissionGenerated linker script contains:BKPRAM (xrw) : ORIGIN = 0x40036400, LENGTH = 2KThe x (executable) flag is incorrect. BKPSRAM is a data-only backup memory — it is not executable. According to RM0481 sec. 2.3, BKPSRAM is accessible only via the system bus (S-AHB), not the code bus (C-AHB). Marking it executable is misleading and may cause incorrect MPU configuration.Expected:BKPRAM (rw) : ORIGIN = 0x40036400, LENGTH = 2

I’m seeing that the X-CUBE-FREERTOS packege is being updated to 1.6.0 to support FreeRTOS 11.2From the changelog it says that it’s restricted to    - Restricted to processor vendor: STMicroelectronics:13    - Restricted to processor name matching: STM32H5*|STM32U5*|STM32C0*|STM32WBA*|STM32U0*|STM32N6*|STM32U3*Are there any plans to bring to STM32H7* as well?

I have the latest version of STM32CubeIDE for Mac with an Apple Silicon (2.1.1).From time to time, I get the messageWhen I check the program informations, it confirms that I have the correct version (Apple Silicon).I think the problem is caused by Eclipse (version 4.33), which is out of date.Is there an upcoming update for STM32CubeIDE with the ARM version of Eclipse? 

Hi,I am using an STM32U585 MCU in a Iot Application . I am facing an issue during power-up.Problem description: When the main supply is turned ON, the MCU appears to hang or gets stuck somewhere during startup. If I press the reset pushbutton connected to NRST, the MCU starts working normally. After that, the system runs without any issues. Every time I turn the main supply OFF and ON again, the same problem occurs. A manual reset is required for proper operation. This behavior is observed with different power supplies as well. Hardware details: MCU: STM32U585 NRST pin: 10k  pull-up or 100nf capacitor connected Pushbutton reset available on NRST   Any suggestions or recommended checks would be greatly appreciated.Thank you.

I use one Nucleo-F401RE create one project for TIM1-CH1-DMA, check RM0368 (rm0368-stm32f401xbc-and-stm32f401xde-advanced-armbased-32bit-mcus-stmicroelectronics.pdf) table 29, I can use DMA2_stream 6.(support ch1,ch2,ch3)When I open CUBEMX, there doesn’t support ch1, only support ch3, which one is correct CUBEMX or RM0368?

Hi everyone,I am encountering an issue where my MCU freezes during continuous data transmission, and I am looking for some advice or debugging directions.Hardware & Setup: MCU: STM32U575 Network Module: ST67W611M1 Protocol: TCP Driver/Firmware Version: V1.3.0 Issue Description: My application is designed to send a 1KB data packet to a remote server every 3 seconds. The transmission works perfectly fine at the beginning. However, after successfully transmitting several hundred KBs in total, the MCU gets stuck.Through debugging, I found that the firmware completely hangs inside the W61_Net_SendData() API.Observations: The remote server is confirmed to be alive and functioning normally when the hang occurs. The MCU does not hard fault; it simply blocks indefinitely inside W61_Net_SendData(). My Questions: Are there any known issues regarding buffer overflows or memory leaks in this specific API when sending large amounts of data over time? Is there a way to configure a non-b

Hello,I realized, that there are different informations about the features of LPUART1 in the datasheet and refmanual.The datasheets (at least DS15125 and DS15136) probably falsely specify in Table 8, that the LPUART1 features receiver timeout interrupt, modbus com and auto baudrate detection.In the refmanual (RM0522, Table 439) these features are specified as not supported. This seams to be the right information, when looking into CubeMX2, where the RTO for LPUART1 can not be activated.  

Hi.I’m working with a Nucleo H7A3ZI-Q. It used to work fine, but one day after we did some measurements it suddenly stopped refused to download code. I’m now trying to troubleshoot it. When connected to STM32cubeprogrammer, the board is detected well, but it does not connect, and gives me this error: and this error in the fail.txt: The interface firmware FAILED to reset/halt the target MCU I am also able to update the card with STLink Updater through STLink-V3, which I have done succesfully, but the result remains the same. I have tried on a mac and a windows.

Hi, I’m trying to identify the part number of a STMicroelectronics LDO that is on one of our boards to verify it is the correct part through the device marking. I saw on another forum post that the device marking decoding information is something that only STMicroelectronics has access to internally. Could I please get help identifying the part circled in red by it device marking? It looks like it say 8L533. The part is supposed to be L78L15ABUTR. Thank you,John Sharp Screenshot 2026-06-17 144356.png

Could you tell me VL53L8CX FDA Accession Number?

I have an EtherCAT project that uses the open-source software EtherCAT master station IGH.Currently, my platform is the main controller STM32MP257, and the relative jitter of IGH--enable-generic is relatively large.I would like to inquire if ST has provided corresponding real-time network card driver patches for the EtherCAT master station IGH?If there are any other better solutions, please let me know. Thank you~

Hello, I am trying to setup TIM5 channel 1 to output a signal on its output pin. I generated the code using STM32CubeMX2. I am getting an assert failed during initialization.mx_system_init() calls mx_tim5_init() which calls HAL_TIM_OC_SetConfigChannel(): oc_config.polarity = HAL_TIM_OC_HIGH; oc_config.idle_state = HAL_TIM_OC_IDLE_STATE_RESET; if (HAL_TIM_OC_SetConfigChannel(&hTIM5, HAL_TIM_CHANNEL_1, &oc_config) != HAL_OK) { return NULL; } In HAL_TIM_OC_SetConfigChannel function assert fails at the following line: ASSERT_DBG_PARAM(IS_TIM_OC_OVERRIDE_STATE(p_config->override_state)); ASSERT_DBG_PARAM(IS_TIM_OC_BREAK_MODE(p_config->break_mode));The value of the override_state shown by the debugger  is: (HAL_TIM_OC_OVERRIDE_SET | unknown: 0xfa). If I comment out the assert it will assert on the next line (break_mode). If I comment that line out as well the code outputs a signal on the pin. I attached my MX2 file. What am I missing?-Gil 

Hi everyone,I'm using an STM32U599VJT on a custom board and I'm having trouble getting USB to work.ProblemThe MCU cannot be detected by a PC through USB under any condition: USB DFU mode does not appear when entering the system bootloader. USB also does not work from my application firmware. Windows reports "Unknown USB Device (Device Descriptor Request Failed)" (Error 43). What I Have Verified The MCU successfully enters the system bootloader. I can program and communicate with the device through the UART bootloader without any issue. Therefore, I am confident that the MCU is actually entering the ROM bootloader. VDDUSB is powered at 3.3 V. VBUS sensing is connected and reads approximately 3.3 V when connected to the PC. USB-C CC configuration is present and the board receives power correctly from the PC. USB D+ measures approximately 3 V. USB D− measures approximately 0 V. The board uses a 25 MHz HSE crystal. The USB signals pass through a USB mux that is shared

Hello, I am using CubeMX2 Version 1.0.0 on macOS Silicon. Various software packs fail to install with a 404 error like this: Could not fetch content of pack-URL: https://developer.st.com/st-pack-server/api/v1/pack/STMicroelectronics.rot_provisioning.2.0.0.pack, got: 404 - Not Found The following packs where tested and failed: rot_provisioning eeprom_emulation mcuboot fileX usbX (now installed via local pack from https://dev.st.com/stm32pc/) Is this an error on my side, similar to the proxy or certification issues I saw in other tickets or are these packs just not available YET? Secondly, I see support packs for e.g. the L4 MCU series: "stm32l4xx_dfp". What is the point of having these packs if CubeMX2 will not support these MCUs?

Hi everyone, I have successfully set up a camera and the NPU working together on a Nucleo N6 to get proper outputs from the latter, which is great. I also have a way to see the image and can verify the outputs live.However, that only works when I launch the firmware by adding the Application to the startup, loading its symbols, flashing the trusted application and starting to debug the FSBL… After that starts, I can detach the debugger to let it run the application. (BOOT0 off, BOOT1 on)When I now flash both trusted binaries and launch without the debugger (BOOT0 and BOOT1 off) it starts normally and I see the live image. But there are no inference results (which takes the same amount of time as when it worked)… What could I be missing?Best regards, rphii

Hello,I use a STPM32 on a battery charge system. The STPM32 is associated with an ESP32 module.The driver used is from ST (V1.0, 17 may 2016).I want to detect some defaults with interrupt, and I configure the interrupt mask only for current and voltage swell.But when I launch a battery charge, an interrupt is triggered (the period error interrupt) which is not masked.I don't understand this behavior and don't find an answer in the datasheet.Any help would be appreciated !Best regardsGilles.