AutoDevKit Ecosystem

Hello everyone,I am experiencing a persistent debugging issue using AutoDevKit Studio. The debugger connects successfully to the target, but the application never reaches the main() function, immediately hanging at an exception handler.Here are the details of my setup and the issue:1. Part Number Target Board: AEK-MCU-C4MINI1 Debugger: AEK-MCU-SPC5LNK  2. Environment IDE: AutoDevKit Studio (Eclipse-based) on Windows 11. Toolchain/Debugger: GDB OpenOCD Debugging (OpenOCD 0.12.0+dev).  3. Schematics Standard ST evaluation board (no custom schematics). 4. Details When I launch a debug session, OpenOCD connects successfully, halts the target, and identifies the chip. However, the execution is stuck with the following error: Break at address “0x404100 with no debug information available, or outside of program code.I am fully aware that the "Source not found" window shown by the IDE is simply a consequence of the core hanging at this specific exception handler address (which naturally la

Im using SPC58C80E5, working on Autodevkit studio, #include "components.h"#include "can_lld.h"#include "can_lld_cfg.h"#include "pal.h"#include "osal.h"/* Define your custom CAN packet ID for triggering the reset */#define FLASH_RECOVERY_CAN_ID  0x7F0UCANRxFrame rxmsg;void HandleBootloaderRequest(void) {    /*       Check Mailbox 0 of CAND2 (which your working reference project proves       is the exact driver module tied to your physical PB9/PB10 pins).    */    if (can_lld_receive(&CAND2, 0, &rxmsg) == CAN_MSG_OK) {        /* FIXED INVERTED LOGIC: pal_clearpad pulls pin LOW, turning LED 2 (PH4) ON */        pal_clearpad(PORT_H, 4U);        /*           MATCH VERIFICATION: Using the exact '.SID' layout and array index bracket           notation proven to execute successfully on your hardware bench.        */        if (rxmsg.SID == FLASH_RECOVERY_CAN_ID && rxmsg.data8[0] == 0xAA) {            /* Cleanly disable system interrupts before register access */            irqI

How tp flash the .elf through CAN , i’m using SPC58EC80E5 and working on Autodevkit studio. 

I’m using SPC58EC80E5 and i wanted to load the files into unit without using JTAG, so that i wanted a Bootloader, How to work on that and if any sample projects are there for reference ? I already searched for this project “SPC582Bxx_RLA Bootloader Test Application for Discovery” it was no there.In fields i should load the project without using JTAG , i have only connection with CAN.

Hello, I am experiencing some issues when using ETH0 (LAN8670). As a test I want to use ETH1 to use LAN8650 via SPI communication. How can I use ETH1 when calling FreeRTOS_recvfrom(), FreeRTOS_sendto(), etc? I changed SPC5_USE_ETH0 as FALSE and SPC5_USE_ETH1 as TRUE but still I can’t use ETH1, I do not see any packet from ETH1’s port of Evaluation board via Wireshark in the connected PC. Questions;Is there additional #define to change if I want to use ETH1 (through SPI) but not ETH0 (through MAC)? Or do I need to call different FreeRTOS API functions? Currently I am calling some Ethernet related functions like below.  UdpRxInfo.xRXSocket = FreeRTOS_socket(FREERTOS_AF_INET, FREERTOS_SOCK_DGRAM, FREERTOS_IPPROTO_UDP); FreeRTOS_setsockopt(UdpRxInfo.xRXSocket, 0, FREERTOS_SO_RCVTIMEO, &xReceiveTimeOut, sizeof(xReceiveTimeOut)); UdpRxInfo.xBindAddress.sin_addr = FreeRTOS_inet_addr("192.168.0.22"); // use Specific IP to receiveUdpRxInfo.xBindAddress.sin_port = FreeRTOS_htons(XcpPortNum);

I’m working on SPC58EC80E5 in autodevkit studio , serial tranmitter is working but serial recevier is not working , i attachesd the serial driver coniguration check it and also my main.c is below   #include "components.h"#include "serial_lld_cfg.h"#include <stdio.h>#include <string.h>uint8_t ch;char    buffer[20];uint8_t idx   = 0;int     value = 50;/* ── Strip \r and \n from string ── */static void stripNewlines(char *str){    int i = 0, j = 0;    while (str[i] != '\0')    {        if (str[i] != '\r' && str[i] != '\n')            str[j++] = str[i];        i++;    }    str[j] = '\0';}int main(void){    char msg[50];    componentsInit();    irqIsrEnable();    sd_lld_start(&SD12, &serial_config_configuration_name);    sd_lld_write(&SD12,        (uint8_t *)"UART Ready. Send number like 120#\r\n", 35);    while (1)    {        if (sd_lld_read(&SD12, &ch, 1) == 1)        {            /* ── ignore \r and \n completely ── */            if (ch == '\r' ||

Hello everyone,We are currently designing a decentralized Battery Management System (BMS) node for our Formula SAE electric car. We selected the L99BM114 due to its robustness in automotive environments and high measurement accuracy.Our architecture requires this specific node to monitor a 5-series (5S) cell module. Since the L99BM114 supports up to 14 series cells, we will have 9 unused channels.While reviewing Section 6.8 of the datasheet (Unmounted cells), the exact hardware implementation for our case felt a bit ambiguous. We want to ensure our schematic doesn't trigger false internal diagnostics, such as Cell Open Wire or Balancing Short/Open.Could anyone clarify the recommended wiring for the unused pins in a 5S configuration? Specifically:Voltage Sense Pins (C6 to C14): Should all these unused inputs be shorted together and tied to the highest active potential (C5)?Balancing Pins (S and B) & Filtering: How exactly should we handle the external filtering resistors (RLPF) and

Hello support team, I just received a new AEK-COM-10BASET board and trying to connect Lauterbach debugger with License module for MPC55xx. Question : How can I connect to the board through Lauterbach debugger & SW? Currently the SW (TRACE32) shows error message when I press "Up" button. I have no idea why such "Target Power Fail" error or "Power Down" message is appeared.Also I checked below 11 pin and the measured voltage is 3.3V. The jumper (switch) configuration I made are ;JP1~JP7 : closed = shortJ13, J14 : I tried both 1-2 and 2-3 connection Any comment is appreciated, thanks! Best regards,apap  

Hello Max VIZZINI ,I'm using SPC58EC80E5 evaluation kit in that im working on SARADC , PB[1] i'm taking as ADC pin and connected 10k potentiometer to it.im getting continous 8192 adc value even after rotating the potentiometer , im using 12 bit ADC  and checking the ADC values in CAN bus, i shared related configuration check it and please help me to solve this issue.  #include "components.h"#include "saradc_lld.h"#include "saradc_lld_cfg.h"#include "can_lld.h"#include "can_lld_cfg.h"#include "osal.h"#define ADC_CHANNEL 66Ustatic uint16_t adc_value;CANTxFrame txmsg;int main(void){componentsInit();/* Start ADC */saradc_lld_start(&SARADC12D1, &saradc_config_saradcconf);/* Start CAN */can_lld_start(&CAND2, &can_config_mcanconf);/* CAN frame setup */txmsg.IDE = CAN_ID_STD;txmsg.SID = 0x123;txmsg.RTR = 0;txmsg.DLC = 2;while (1){/* Start ADC conversion */saradc_lld_start_conversion(&SARADC12D1);/* Wait for conversion */while (SARADC12D1.saradc->ICDR[ADC_C

Hello,   I installed AutoDevKit Studio today and trying to create the AEK-COM-10BASET project from it.   Basically there is no option to create / start the AEK-COM-10BASET from AutoDevKit.   Also I tried to run Help > Install New Software > Work with http://autodevkit.spc5studio.com/ > Choose AEK-COM-10BASET > install the module.   Even I tried couple of times it always fails due to unknown reason. After Fetching children step, the SW says "Cannot perform operation.", the SW tries to install some modules, and finally nothing is improved. Still I cannot start any AEK-COM-10BASET project.   If I try to install the SW modules for AEK-COM-10BASET, it says below error message.   And stucks here, I cannot move further. No AEK-COM-10BASET related menu items / projects are found, I cannot start.   I want to get the AEK-COM-10BASET project source code, change something and do some of my own tests. Any help / comment are appreciate

Working with AutodevkitStudio using AEK$MCU-C4M3A and AEK$MCU-SPC5LNKA, how to create a project for led blinking give step by step explaination.   

Hello Max VIZZINI,i'm facing issue in printf() in AUTODEVKITSTUDIO. im using printf() in the code after compiling im getting this error c:/autodevkitstudio-2.7.0/eclipse/plugins/com.st.tools.spc5.tools.gnu.gcc.ppcvle.win32_4.9.4.202511271245/toolchain/bin/../lib/gcc/powerpc-eabivle/4.9.4/../../../../powerpc-eabivle/lib/e200z4\libc.a(lib_a-sbrkr.o): In function `_sbrk_r':sbrkr.c:(.text._sbrk_r+0x1a): undefined reference to `sbrk'c:/autodevkitstudio-2.7.0/eclipse/plugins/com.st.tools.spc5.tools.gnu.gcc.ppcvle.win32_4.9.4.202511271245/toolchain/bin/../lib/gcc/powerpc-eabivle/4.9.4/../../../../powerpc-eabivle/lib/e200z4\libc.a(lib_a-writer.o): In function `_write_r':writer.c:(.text._write_r+0x1e): undefined reference to `write'c:/autodevkitstudio-2.7.0/eclipse/plugins/com.st.tools.spc5.tools.gnu.gcc.ppcvle.win32_4.9.4.202511271245/toolchain/bin/../lib/gcc/powerpc-eabivle/4.9.4/../../../../powerpc-eabivle/lib/e200z4\libc.a(lib_a-closer.o): In function `_close_r':closer.c:(.text._close_

i'm using SPC58EC80E5 in that pin number 28 TX and 29 RX , in low level drivers configuration i dont know which MCAN to be select please help me and also if i want to configure any other CAN ,which MCAN i should select. below is my configuration screenshot check it .

Evaluating the L9963E BCC chip for a BMS design, using the AEK_POW_BMSNOTX eval board together with AEK-MCU-C4MLIT1 (spc58ec) running the example BMS application as reference but seeing some odd results in the cell voltage readings.All readings are a bit low compared to actual cell voltage, but cell1 and cell14 are off by a fairly large amount.What could be causing this?cell1 & cell14 reading off by 0.5vcell2 to cell13 reading off by about 0.1vCell1 reading seems to improve if the HotPlug selection jumper is mounted. But not cell14.

Good morning!I've been working in a project whose purpose is communicate AEK-MCU-C1MLIT1 board and AEK-COM-ISOSPI1 through SPI/isoSPI protocols. At first, I've tried to apply the hardware configurations and script as mentioned in the user manual(UM3187) to exchange 512 bytes between two devices through isoSPI, however I don’t know how reliable the results in debug step are to assure this communication is working properly. Another detail that I've noticed is about disable pin, which stay always turned on, mainly when I select configuration as “micro” in  AEK-COM-ISOSPI1 Component RLA > Application Cofiguration. What should I do to enable AEK-COM-ISOSPI1 board?About the wire connections, I used as reference the board view within AutoDevKit Studio. I’d like to know if there is some connection that is missing, especially about the ISOm e ISOp signals, because the board view doesn’t show if I should to connect the USB port on the computer to debug step, for instance. 

Hi all,While implementation of CanTp, I am getting some errors regarding undefined reference which are shown in the snippet attached. I debugged completely but I am unable to find from where and for what these errors are coming.It would be more helpful if I get some support regarding this issue. Updating MediaThanks,Shiva Shankar.

Hi, I am looking to use AEK-POW-BMSWTX battery management system for EV related battery management experiments. Please let me know if I can use AEK-POW-BMSWTX with STM32 microcontroller boards. Also please let me know if any other boards are required to perform experiments with AEK-POW-BMSWTX. Thanks and regards

hi community  i am using  "AEK-AUD-C1D9031"  board. in this board i had flashed  .WAV files and i had played. the wave files are played using an example code given in the autodevkit. i used an API playsound() this one will give good sound when i had used playsoundwithgain() -> the gain with range (15,17) the sound quality was good with decent amount of volume. but hear i want to control the volume  (0db - 75db),but by using playsound() and playsoundwithgain() i am unable to control the volume( the sound will be very noise when i had used gain in range of ( (0-14) and (17- so...on) ). so is there any alternatives to control the volume of the sound.   hear is the pic of the function which i had used.

Hello, I have been trying to make the AEK-MCU-LNK work with my SPC56 discovery board with OPENOCD (I reached a dead end trying to make the .cgf files). So I have two questions:1.- I understand that the AEK-MCU-LNKU works with this SPC56 family using UDE. Is that true?2.- I saw in another post (https://community.st.com/t5/automotive-mcus/stellarlink-vs-spc5-udeskt/td-p/64794) in the last answer, that AEK-MCU-LNK with the UDE driver should work with SPC56 family. Can you please confirm this?Thanks,Agustín

Hello, I am using SPC582Bxx controller. I want to configure software watchdog timer in my project. How to add that SWT. Currently I'm using autodevkit studio for software development. Please tell me how to configure that?Thank you,

Hi Team,i am working in the daisy chaining bmscctx and bmscc using a Pi MCU. I was able to get the values using only bmscctx.now i am having issue when i connect the bmscc also.the problem i find is in the user manual3185, the figure for daisy chain is given as:and it says to connect ISO Hp to ISO Lm of the next node (that is opposite polarity).but when i looked in the L9963E datasheet, it is given as :Here ISO HP is connected to ISO LP (that is same polarity)so my doutb is which among the above should i follow. And due to this i think my values after daisy chain is not displayed.My second node is not assigning as my daisy chain is not configured correctly.( i am using mcu as pi btw)Thank You.  

Dear community,I am currently working with the SPC58 E-Line processor placed in the mother daughter evaluation board.I am using the AEK-MCU-SPC5LNK with OpenOCD. The reference manual for the E-Line is similar o the G-Line. I have only found the SVD file for the G-Line, so I therefore thought, that using this SVD file could work. Sadly the peripherals remain blank and I cannot see any memories.I would be very happy if someone could tell me, how to get the correct SVD file or what do I have to change to get it running.Kind regards,Tassilo P.s I have used the attached manual, to access the peripherals: How to use the AEK-MCU-SPC5LNK programmer and debugger for SPC5 automotive microcontrollers - User manual

I'm working on a battery management system using an STM32F302 going to an AEK-COM-ISOSPI1 dev board using the L9963T transcevier which is daisy-chained to 10 AEK-POW-BMS63EN boards using the L9963E chip.The problem that I'm having is that when I send a message over the ISO SPI lines, it adds an additional 0 before it sends the message.I have attached two messages that show the leading 0 bit that is added. msg 0x55 55 55 55 55 and msg 0xFF 00 FF 00 FF. SPI settings are8 bits frame MSB first Baud rate 1000 kbits/secCPOL lowCPHA 2 edgeCRC Disabled How would I go about removing the leading zero from the message? Any help would be greatThanks

Hello team,I am using the GUI demo (single) for BMSCCTX and C4MINI with 4 LFP Batteries. I have followed the steps described by @ritehracingteam in this thread.After I run the program from the AutoDevKit Studio, my D9 and D2 LED are lit up and D8(Blue) is blinking. D7 remains turned off. Which according to the documentation means SPI is not working.I made sure Hotplug connection is made and the pin configuration is correct, also checked all the connections.Is there something I might be missing?Regards,Zen

Hi team,I have seen example of C4MINI1 daisy chaining BMSCCTX with BMSCC which is working fine.I have 2 BMSCCTX, so i was wondering that i can connect 2 BMSCCTX for daisy chaining with C4MINI1.But i have noticed that in the datasheet of CCTX, the daisy chain receiving pins are not mounted inside,(which is mounted for BMSCC only. So does it mean i cant use 2 BMSCCTX as node and use dual access configuration?Can anyone explain about this please.Thank You.