Solved

Posted on May 03, 2018 at 23:59Can someone explain me how USB HS is clocked, when using embedded PHY?

Posted on May 07, 2018 at 18:26Hi,Is there any doc mention about STM32L4 (STM32L4996 and STM32L4A6) ISR source? The doc I found from both ST and ARM reference manual do seems list all of the ISR source.Thanks,****Note: this post was migrated and contained many threaded conversations, some content may be missing.

Posted on May 08, 2018 at 20:36Hi,I have a STM3221G-EVAL board with the STM32F217IGH6 and am trying to program over CAN. I checked the revision code on the chip to see what version bootloader it has and found it was a revision '2' chip. I can't find any information though on what bootloader is on these chip revisions and whether it supports programming over CAN.. I could only find an errata sheet for this revision. Any help is appreciated, thanks.

Posted on July 17, 2015 at 10:58Hello, I'd like to know if there is a 'magical' way to syncronize the bit stream with the channel signal in the i2s receivers. I don't have control on the external stream ( slave mode), so the serial clock is free running, and the only way I've found to use the interface is to wait for the correct time to enable it.Perhaps there is some way to do it using the receiver but I've been unable to find it.If this is a 'feature', perhaps it would be wise to modify the silicon on next iterations/products to allow for an automatical way to sync the receiver with the data stream.Thank you very much.Albert #i2s #stm32f407 #sync

Posted on May 08, 2018 at 12:39I can't choose the STM32F413 neither from MCU selector nor from Board Selector (NucleoF413) in CubeMX as new project. The Check Update Manager reports all software is up to time.

Posted on March 24, 2018 at 14:24The user manual mentions using one 88% reflectance target and 17% reflectance target for calibration. I don't know what material has those reflectance values. What exactly should I use for calibration and where can I get those?

Posted on May 07, 2018 at 20:19Hi.I was just programming my stm32f217 board via serial wire interface and everything was ok, but when I wanted to program once more the message ''No target connected''displayed and it didn't program my MCU anymore.But when I use IAR to program stm8 it works.What is the problem?I tried updating the firmware but the message bellow displayed that I don't know what it is.

Posted on April 10, 2018 at 12:25Hi,I'm building an UHF RFID reader using ST25RU3993 and I have a problem reading the registers. The idea is to connect the IC to NodeMCU or Arduino (both are programmed using Arduino IDE at this stage).I connected MISO to MISO and MOSI to MOSI (I�m assuming there is an error in the datasheet Figure 3 p.15)After enabling the IC (EN = 1) and waiting 1 second I try to read registers, but the IC does not respond to my SPI messages. I can see NCS, CLK and MOSI signals on the oscilloscope, but the MISO is always LOW. My code reads registers 0x00 to 0x24. The SPI was set to MODE1 (NodeMCU outputs data on rising edge and captures it on Falling edge as instructed in the datasheet p.15).I tried different frequencies: 1kbps, 100kbps, 1Mbps, 2Mbps and 5Mbps.According to the datasheet the IC should be in NORMAL mode and therefore the SPI communication should be possible after enabling the device.I also see voltages at some of the pins (voltage regulators) so the de

Posted on May 06, 2018 at 18:41Is it possible to do ADC SCAN conversions without using DMA?#adc-scan-continuous #stm32f103rb #adc

Posted on December 07, 2016 at 17:15Hi ST,You have this site: http://www.st.com/content/st_com/en/about/events/events.html/stm32cube-basics-online-course-with-hands-on-exercises-a.htmlHowever, I never received log-in details after registering for this. Are you still running this course? If so, how do I get my login? If not, where is the best place to learn CubeMX?

Posted on May 05, 2018 at 01:12I'm currently working on an STM8L052C6 project, and am looking to set up some interrupts on Port C pins. Looking at the pin description in the datasheet http://www.st.com/resource/en/datasheet/stm8l052c6.pdf, it appears that Port C pins should be capable of being configured as external interrupts. However, looking at the interrupt table from the same document does not show any entry for Port C. However, it does contain entries associated with Port G and H, both of which do not exist on this particular package. So it appears there is an error in the datasheet.With this in mind, is configuring Port C pins as external interrupts possible on the STM8L052C6 chip? If so, what is the proper IRQ number to use?#interrupts #stm8l052c6

Posted on January 12, 2018 at 12:46Hello,I am trying to implement a long 1D capacitive touch slide sensor or around 7 or more separate capacitive touch buttons using STM32F103. I read that the touch sense library is not available for F103. Is this correct? Does the F103 lack touch functionality? Does ST provide any means of implementing touch sensing with F103?On Github / the net, I find an implementation for STMDuino, but no implementation in C using the current HAL or LL environment. What other libraries or examples of touch buttons for F103 are available or easy to port?Thank you & regards,Christoph#capacitive-touch

Posted on May 04, 2018 at 20:02What are the GPIO Pins for ADC 1 in STM32F103RB? I can't find it in reference manual.Thanks!#adc #gpio #stm32f103rb

Posted on May 03, 2018 at 21:38Hi,I know it's rather a question to Keil but maybe someone came across this issue.The uVision cannot find STM32L496ZGTxP MCU when the IDE starts.  The current DFP is 2.0.0 (2017-10-06).I ignored the warning and successfully compiled simple program.It seems I have no access to peripherals during debugging session.The project skeleton was generated using CubeMX 4.25.0Keil uVision 5.25. I have not found never Device Pack than 2.0.0

Posted on May 02, 2018 at 18:10Hello,I have a question regarding a note in the datasheet of the LIS3DH accelerometer:I want to use the accelerometer LIS3DH for one of my application with the following specifications:- The accelerometer is supplied at 1.8V (in compliance with datasheet).- The functions to be achieved are: orientation detection and  provide temperature.I saw the following note in the datasheet:'The product is factory calibrated at 2.5 V. Temperature sensor operation is guaranteed in the range 2 V - 3.6 V.'What those that means? The temperature sensor is not working when the accelerometer is supplied at 1.8V ?Thanks for your help.#accelerometer #lis3dh #temperature-sensor

Posted on May 02, 2018 at 20:48I'm using the gate mode TIM scheme as detailed in the reference manual:TIM3->CCMR1 |= TIM_CCMR1_CC1S_0; /* (1)*/ TIM3->CCER |= TIM_CCER_CC1P; /* (2) */ TIM3->SMCR |= TIM_SMCR_SMS_2 | TIM_SMCR_SMS_0 | TIM_SMCR_TS_2 | TIM_SMCR_TS_0; /* (3) */ TIM3->PSC = 0; /* (4) */ TIM3->ARR = 65000; TIM3->CR1 |= TIM_CR1_CEN; /* (5) */This works perfectly for channel 1.Now I'm trying to dynamically change channels, and I can't seem to wrap my head around the masks.I've tried a number of register masks, likeTIM3->CCMR1 |= TIM_CCMR1_CC2S_0 | TIM_CCMR1_CC1S_1; /* (1)*/and TIM3->CCMR1 |= TIM_CCMR1_CC2S_0; /* (1)*/But I haven't been able to get the input to switch..sorry for such a stupid question, I'm sure there's something in the reference manual that I'm missing.#input-capture-mode #tim #timer-gated #tim-pwm

Posted on May 02, 2018 at 03:43The TIM2 timer on an STM32F0 seems to not be resetting to 0 once the counter reaches the ARR value on occasion. I am periodically changing the ARR value, but the values are all in a small range. After a random amount of cycles, the counter will increment beyond that range without triggering an update event, resetting the counter back to 0. I have tried this with and without TIM_CR1_URS set. TIM_CR1_UDIS bit is in the reset state. Anyone else run into this problem?

Posted on May 03, 2018 at 22:48I have a problem with STM32F437, USB OTG Library 2.2.0  and USB HS with embedded PHY, CDC device.First enumeration never pass in the right way (see the attached file).After unplugging and plugging the cable, everything is OK.I'm using Windows 10 and in the MCU, USB sensing is not used.One ugly solution is to reset the HS OTG peripheral after first connection and reinit it again.Any idea?#cdc #stm32f437 #usb_otg

Posted on April 29, 2018 at 16:15Hi,I'm having trouble working with ST25R3911B while its connected to a Raspberry Pi.My need is to have a program that can read/pool on the ST25 to read RFID tags if they are present.I've downloaded the ST25 SDK and created a Java application according to the provided examples, compiled successfully.The problem is that the libraries provided with the SDK for Linux are 64 bit, while RPI are arm32v7, not arm64.At first, I got the following exception:Java HotSpot(TM) Client VM warning: You have loaded library /usr/lib/libhidapi-libusb.so which might have disabled stack guard. The VM will try to fix the stack guard now.It's highly recommended that you fix the library with 'execstack -c <libfile>', or link it with '-z noexecstack'.Exception in thread 'main' java.lang.UnsatisfiedLinkError: /usr/lib/libhidapi-libusb.so: /usr/lib/libhidapi-libusb.so: wrong ELF class: ELFCLASS64 (Possible cause: architecture word width mismatch)I've managed to build and in

Posted on May 02, 2018 at 19:18In the latest versions of IAR Embedded Workbench (8.22.X), I am no longer able to view any of the peripheral registers.  I used to do this in the 7.X.X versions using the Registers window, but now I can only find the Current CPU registers.  Does this feature still exist in the latest IAR EW, and if so how do I find it?Ricardo

Posted on April 30, 2018 at 13:32Hi guys,I'm using the  STM32L475RCT in a custom board. When using the JLink everything is working fine but when I discounnect the Jlink and power cycle the board the application doesn't work at all. Each time I have to force NRST to 0 and release it in ordre to make the application works.I have 100nF capacitor between the NRST pin and GND as recommended in ST  datasheet( 6.3.15 ).I checked the voltage on the NRST pin and it seems correct : it goes from 0.358V to 3.1V  in ~4ms at board power up which follow the required low level voltage ( VIL(NRST)  =0.3?VDDIOx = 0.984V) and high level reset voltage  ( VIH(NRST) = 0.7?VDDIOx = 2.29V).Any thoughts on where the problem might be ?#stpm32-reset #reset #stm32l4 #nrst #reset-problem

Posted on April 19, 2018 at 21:01Hi, Just started to test a prototype based in the old FENTO Reader Hardware using the AS3993, now AKA ST25RU3993.I am able to read/write registers using the SPI pins, but I cannot generate an interruption.I have been trying to execute the interruption using two methods. First Method:1 -Write 0x20 to Register 0x35 (Enable FIFO Interrupt)2 - Write 0x03 to Register 0x3D (Set 48 Bytes for Transmission)3 - Send the Comand 0x90 (Transmission with CRC)4 - Write 4 bytes to address 0x3F, 6 times (Supplying less bytes to generate an interrupt)Pin IRQ stays LOW.Second one:1 -Write 0x00 to Register 0x35 (Disable All Interrupts in this Register)2 - Write 0x40 to Register 0x36 (Enable End of Comand Interruption)3 - Send the Comand 0x87 (Start AD Conversion)Pin IRQ stays LOW.This tests are the same ones used by ST and AMS in their sample codes.I am sure the MCU pin is working correctly and detecting the rising edge in the correct pin. Tested. I am also sure that the

Posted on April 25, 2018 at 13:01Hi all,This is a question regarding STM32F0 TIM3.I have written this code in keil compiler/***** main.c*****/&sharpinclude<stm32f0xx.h>&sharpinclude<stm32f030x8.h>void GPIO_Init(void);  void TIM3_Init(void);int main(){ GPIO_Init();         // Intializing PA5 TIM3_Init();  while(1) { } }void GPIO_Init(){  // Enable clock for GPIOA RCC->AHBENR |= (1<<17);  //Configuration of PA5 GPIOA->MODER |= (1<<10);             // PA5 as general purpose output mode GPIOA->OTYPER &= ~(1<<5);            // PA5 as output push pull GPIOA->OSPEEDR |= ((1<<10)|(1<<11)); // PA5 at high speed GPIOA->PUPDR &= ~((1<<10)|(1<<11));  // PA5 as no pull-up,

Posted on April 08, 2018 at 08:59I need a sensor that is able to differentiate between distance 20mm and 23mm with no error.i.e. the accuracy and stability must be high (within 1mm only)which sensor should I use VL6180 or VL53L or something else?

Posted on May 01, 2018 at 12:39Hi.I was working with my new stm8s105 MCU trying to get started with the timers.But every time I use the command to display the time on the LCD the same number showed every time.I thought that the problem is my timer code but when I just put a number on the LCD to show it just showed an irrelevant number.I use the same LCD.h on LPC1768 and STM32F2 and just converted the same header.The only difference is that I used Keil compiler for them and now I'm using IAR.lcd_gotoxy(1,2);sprintf(buf,'%d',100);lcd_print(buf);delay_ms(1000);This is a simple code that must show 100 but it displays 12594>:(The characters are displayed properly.The problem is numbers.