Solved

Posted on April 25, 2018 at 21:56Looking at the data sheet for the VL6180X (p49-50), the registers are listed with their 'offset' address.Does this mean I have to add a base address to the offset addresses? If so, where is that found in the documentation, please? And, is there a register listing that has the actual register addresses somewhere?Thank you.

Posted on April 29, 2018 at 20:30Cube MX 4.25Generate source using F446 processor for Atollic TS v9CubeMX and TS are up to dateget following error:..\Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_flash_ramfunc.c:163:30: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'HAL_FLASHEx_DisableFlashSleepMode' __RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_DisableFlashSleepMode(void)(same error for any instance of RAMFUNC prefix.example error line in code is__RAM_FUNC HAL_StatusTypeDef HAL_FLASHEx_DisableFlashSleepMode(void)Line #185 in  stm32f4xx_hal_def.h is#define __RAM_FUNC HAL_StatusTypeDef __attribute__((section('.RamFunc')))which expands toHAL_StatusTypeDef __attribute__((section('.RamFunc')))HAL_StatusTypeDef HAL_FLASHEx_DisableFlashSleepMode(void)Cube32 is remarkably consistent in generating this error.  Since I don't use code executed from RAM (no guarantee that the compiler doesn't), the code doesn't do anything for me except cause an inconvenience.PLEASE f

Posted on April 29, 2018 at 13:55I am using the Nucleo-64 board F401RE, as the name suggest comes with STM32F401RE.The board doesn't have an external clock (X3 mentioned on the board) and still the HSE RDY register gets enabled  , which is actually hardware enabled as per datasheet.int main(void){    RCC_TypeDef *pRCC;    pRCC = RCC;    /** 1) Turn on the HSE Oscillator, by accessing the RCC clock control register (RCC_CR)        * 2) Select HSE as the system clock, by accessing the RCC clock configure register (RCC_CFGR)    */        //1) Turning on RCC_CR by enabling 16 bit.    pRCC->CR |= (1 << 16);        /** We need to wait after the HSE register is enabled for the HSE to become stable,      * This status is show by HSE RDY (Ready) register which enabled by the MCU. (17th bit). &

Posted on April 28, 2018 at 01:37 Hey everyone, I can not seem to get this right and any help would really be appreciated! I'm using a stm32f722ze I have a counter that toggles it's output on every 10th rising clock edge of an external clock that fed into its ETR pin. It also has a slave mode set as rising. Here's the code for the timer: static void MX_TIM8_Init(void) { TIM_ClockConfigTypeDef sClockSourceConfig; TIM_SlaveConfigTypeDef sSlaveConfig; TIM_MasterConfigTypeDef sMasterConfig; TIM_OC_InitTypeDef sConfigOC; TIM_BreakDeadTimeConfigTypeDef sBreakDeadTimeConfig; htim8.Instance = TIM8; htim8.Init.Prescaler = 0; htim8.Init.CounterMode = TIM_COUNTERMODE_UP; htim8.Init.Period = 9; htim8.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; htim8.Init.RepetitionCounter = 0; htim8.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE; if (HAL_TIM_Base_Init(&htim8) != HAL_OK) { _Error_Handler(__FILE__, __LINE__); } sClockSourceConfig.ClockSource = TIM_CLOCKSOURCE_ETRMODE2; sClo

Posted on April 28, 2018 at 12:54Hi,what is the default system clock frequency (previous that all clock configuration take place) on the development board 'STM32F767 Nucleo-144'?Where I can find this information?Thank you for the answer.

Posted on April 21, 2018 at 15:36Where can i get the power measurement firmware mentioned in this application note by STAN4365 Using STM32F4 MCU power modes with best dynamic efficiencyThe project used in the AN is coremark based . Can i get this project ?#stm32discovery

Posted on April 26, 2018 at 10:57Hi everybody,I work on a B-L072Z-LRWAN1 and particularly on the AT_Slave project from I_CUBE_LRWAN. I know that this project uses LPUART via ST-LINK to send AT commands through a terminal to the Murata LoRa module, the pin related are PA2 and PA3 for Tx and Rx.What I would like to do is to switch from LPUART to USART1 (I need to do that for another project). I tried to change the code in order to replace LL_LPUART by LL_USART then I tested it and tried to send AT on USART1 through a terminal plugged to PA9 and PA10 pins (Tx and Rx for USART1) but it didn't work, the code changed is joined.So my question is, is there a way to do what I try to do ? To switch from LPUART to USART1 to send AT commands ?Thank you#lpuart #stm32l0 #usart #i-cube-lrwan #b-l072z-lrwan1 #at_slave

Posted on March 21, 2018 at 07:24Need commands to automate Dfuse3.0.5

Posted on April 25, 2018 at 16:56I am using the simulator for converting solar cells into 5V output to a USB plug. The simulator calculates a 648uH inductor which is VERY large, expensive and hard to find. How can I use a more standard inductor, like the 10uH stated in the datasheet for this design?#spv1040 #solar

Posted on February 10, 2018 at 16:06DocID029085 Rev 2Section 6.15 Virtual COM PortMakes reference to USART3, no other reference in document, and VCP uses USART1 PA9/PA10http://www.st.com/content/ccc/resource/technical/document/user_manual/group0/7c/c9/c0/5f/4e/9b/44/eb/DM00276557/files/DM00276557.pdf/jcr:content/translations/en.DM00276557.pdf 

Posted on April 16, 2018 at 12:37I am using LIS2DH12 on my custom designed board for a BLE application. I noticed that the PCB had a huge current draw than expected and on further digging found the accelerometer to be drawing the excessive current while in Power Down mode. Thorough testing revealed that the SA0 line used to select I2C address was the root cause of this problem. Connecting SA0 to ground (GND) led to huge current draw. However, connecting SA0 to VDD (logic HIGH) solved the huge current draw problem. Is this behaviour expected from the accelerometer? If yes, why? If not, what could be other possible factors leading to such behaviour. Thank you.#current-consumption #i2c-address

Posted on March 07, 2018 at 12:44Hello,is there a way to create run configuration in TrueSTUDIO in a same way as it is in SW4STM32?I would like to 'launch' the code without entering the debug perspective. Just flash and run.Thanks for helping.#truestudio

Posted on April 11, 2018 at 10:04need code for LED ON and OFF for STM32L162VE HW

Posted on April 23, 2018 at 07:40Hello.MCU: STM32L432KC. I'm trying to use SAI1 peripheral in master mode with master clock (MCLK) generation. I've found MCLK has drop pulses. You can see this at attached picture.Clock configuration:1. LSE with crystal 32768 Hz;2. MSI with PLLMODE enabled;3. RCC registers values:CR = 0x0C0000BFICSCR = 0x106F008CCFGR = 0x0PLLCFGR = 0x00001071PLLSAI1CFGR = 0xA8012B00CCIPR = 0x0CSR = 0x1C000600Is i missed something?Thanks.

Posted on November 20, 2017 at 14:56The original post was too long to process during our migration. Please click on the attachment to read the original post.

Posted on April 25, 2018 at 03:31Quote the datasheet:'Temperature data is stored inside TEMP_OUT_L (05h), TEMP_OUT_H (06h) as two’s complement data in 12-bit format, right-justified.'So if the sensor value is reading 0 and the temperature drops by 1/8th of a degree, I would expect the value to be 0xffff or 0x0fff - that is 0bxxxx111111111111. Since 111111111111 is 12 bit two's complement for -1, and the x bits are ignored.However this is not the case. The value I actually read is 0xefff / 0b1111111011111111 / -257. The value continues to count down by 1 per 1/8 degree from here.Can anyone explain what is going on here please?

Posted on April 20, 2018 at 13:37The original post was too long to process during our migration. Please click on the attachment to read the original post.

Posted on April 23, 2018 at 10:35Hi all,I am working on stm32f030c6t6 microcontroller. I want to use tim3_ch1 as pwm output. datasheet says that tim3_ch1 alternate function is available at two pins PA6 and PB4.I am not able to find that which pin default for this tim3_ch1 function and if want to remap another pin then how to do it.I have googled it. I found that in stm32f1 user manual there is a register AFIO_MAPR for remapping of pin for a alternate function.But stm32f0 documents are silent on this.so how I can do it this remapping of pin for a alternate function in stm32f0.

Posted on August 07, 2013 at 18:55Hi all, i'm having issue with DMA on STM32F417, i have configuration DMA1_Stream1 is having trigger updates from TIM6_UP (Channel7), i get after start TIM6 error TEIF1 :( my source code was functional with configuration: DMA2_Stream1 Channel7 + TIM8_UP :( please could you review my sources: ? #define ADC_READ_DMA_TIM_UP TIM6 #define ADC_READ_DMA DMA1_Stream1 static __IO uint8_t ADC_Buffer1[20002]; RCC_APB1PeriphClockCmd( RCC_APB1Periph_TIM6, ENABLE); RCC_AHB1PeriphClockCmd( RCC_AHB1Periph_DMA1, ENABLE); TIM_Cmd( ADC_READ_DMA_TIM_UP, DISABLE); DMA_DeInit( ADC_READ_DMA ); DMA_InitTypeDef DMA_InitStructure; DMA_InitStructure.DMA_FIFOMode = DMA_FIFOMode_Disable; DMA_InitStructure.DMA_FIFOThreshold = DMA_FIFOThreshold_Full; DMA_InitStructure.DMA_MemoryBurst = DMA_MemoryBurst_Single; DMA_InitStructure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single; DMA_InitStructure.DMA_Channel = DMA_Channel_7; DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)(&amp

Posted on April 23, 2018 at 14:54I'm using the X-Nucleo-LPM01A for power measurements. Currently I'm using the STM32CubeMonitor to review the results, but I need to save the data points for further processing. The only file type I seem to be able to save is .stpm and I don't know what I can do with that. Any suggestions?#stm32cubemonitor-power #x-nucleo-lpm01a

Posted on April 09, 2018 at 13:34Hi, i am using CR95H RFID CLICK module with raspberry pi3.I am using UART for communication.I connected,   SSI_1   =>   GND   SSI_0   =>   GND   TX        =>    RX   RX        =>   TX   VIN       =>   3.3X   GND     =>    GND. for waking up i am sending 0x00 and then i send echo cmd but i didnt any response.can any one help me out i new to these modules#include<bcm2835.h>#include <string.h>#include <unistd.h>#include <sys/types.h>#include <sys/stat.h>#include <fcntl.h>#include <termios.h>#include <sys/ioctl.h>#include<stdio.h>uint8_t buf2[11],buf1;void send_data(uint8_t bu

Posted on April 21, 2018 at 21:46Hello all. I am new to STM paradigm. I have a Nucleo 64 STM32L073RZT6 64 PINS board.I was trying to configure the Systick timer, however it seems that the input Systick frequency is always divided by 2.I am using the on-board 8MHz external crystal (which is originally used by the ST-Link interface) but the board marking that I have is MB1136 C-04. According to the hardware pdf, it means that the HSE input of the microcontroller is actually the 8MHz crystal of ST-Link.Here is my PLL configuration (please read the comment maybe I missed something obvious):RCC->CR |= (1 << 16); //HSE on 8mhz RCC->CFGR |= (1 << 22); //PLL out div by 2 RCC->CFGR |= (1 << 0) | (1 << 1); //Select Sysclck as PLL RCC->CFGR &= (~(1 << 7)); //clear bit 7 for AHB prescaler = 1 RCC->CFGR &= (~(1 << 10)); //clear bit 10 for APB1 prescaler = 1 RCC->CFGR &= (~(1 << 13)); //clear bit 13 for APB2

Posted on April 22, 2018 at 01:33hi!I'm trying to play a bit with the CAN bus in the NucleoF091RC, I just generate the code with CubeMX with the CAN_Mode set to Loopback (to use only one node and my scope to see the data), dropped that code in Eclipse and tried to debug it. The debug never passes the MX_CAN_Init(); instruction. If I go a bit deep it stays forever on the loop:/* Wait the acknowledge */    while(HAL_IS_BIT_SET(hcan->Instance->MSR, CAN_MSR_INAK))    {      if((HAL_GetTick()-tickstart) > CAN_TIMEOUT_VALUE)      {         hcan->State= HAL_CAN_STATE_TIMEOUT;       /* Process unlocked */       __HAL_UNLOCK(hcan);       return HAL_TIMEOUT;      }    }In the RM is said the normal mode can be activated once the device it

Posted on February 22, 2018 at 22:48Hi!I'm trying to use the SSD1306 (oled screen) with the STM32F091RC and I2C interface, I managed to integrate the library U8G2 (https://github.com/olikraus/u8g2/wiki ) in Eclipse with GNU MCU Eclipse and the setup provided by CubeMX for I2C. With the 'normal' transmission routines HAL_I2C_Master_Transmit() it works normal, I can draw things there.But when I try to replace it by HAL_I2C_Master_Transmit_DMA(), seems to be some looses between the DMA and the I2C.If I run this with the debugging interface, put a breakpoint in the HAL_I2C_Master_Transmit_DMA() instruction, and look with the scope, I get what is supposed to be each time (because there is a time in between each iteration while I hit the button again), but if I let him run free while I record with the scope again, the received chain is not the same, many packages are lost. I'm testing this with the initializing chain and only in the 'command' section of the transmission, to have it a b

Posted on April 20, 2018 at 14:15Hello Sir Turvey.Clive.002, Neil.AndrewI followed the said instructions and managed a successful IAP test with STM32F429 using support given in.\STM32Cube_FW_F4_V1.21.0\Projects\STM324x9I_EVAL\Applications\IAPHowever, I get memory error (attached as images)  while doing same test with STM32F103C8 using support given in.\STM32Cube_FW_F1_V1.6.0\Projects\STM3210E_EVAL\Applications\IAPSir I have STM32F103 on board therefore I need this fix. As IDE I am using EWARM.#write-failed #stm32-iap