About MattKefford

MattKefford · 2022-07-06

The clear_bit macro in the CMSIS driver is causing a warning when used in the function HAL_CRC_DeInit:

MattKefford · 2021-08-04

Hi, I seem to be having difficulty with what should be a simple I2C task. I want to send the Measurement Request to the Honeywell sensor so it will take a temperature and humidity reading, which requires the following format from their datasheet:I ha...

MattKefford · 2021-04-15

This is less of a question and more of a statement for your information. I was not able to install the v1.6.0 update and have just been ignoring the notifications for a while, so when I saw that v1.6.1 was available I thought I'd try that but it stil...

MattKefford · 2021-03-16

Hi all, I just thought I'd add to the list of questions about USB! :grinning_face_with_sweat:I read AN4879 and it says "when the host presence is detected by the device, the device connects its pull up resistor". This is very clear - first detect the...

MattKefford · 2020-10-11

Hi, I've noticed for the past few versions that this issue has been present. When I switch from a C editor tab to the CubeMX (.ioc file) tab the view transitions properly but when I switch back the other direction, it changes tab to the C file and ch...

MattKefford · 2023-03-19

What I do is the shortcut Cmd + Spacebar then type “cubeprog�? and hit enter. The actual location of it should be Macintosh HD > Applications (it’s buried in the folders STMicroelectronics > STM32Cube > STM32CubeProgrammer). Another option is to do t...

MattKefford · 2023-02-10

To follow up on this, in my can_msg module I tried simply setting the number of filters like:pCanHandle->Init.StdFiltersNbr = 3;And then setting up my filters as so:can_msg_config_filter(0, 0x000, 0x616); can_msg_config_filter(1, 0x216, 0x316); can_m...

MattKefford · 2023-01-18

Thanks for this answer which was helpful for me and I now have filters working on my STM32G0B1. I would also like to know for this part: hfdcan.Init.ExtFiltersNbr = 1;I added this as part of the MX_FDCAN1_Init() function in main.c but my filter confi...

MattKefford · 2022-09-01

I finally managed to install this too with some help from this thread.I downloaded the zip file to my Downloads and unzipped it there.Then in Terminal I did:cd Downloads/en.stm32cubeprg-mac_v2-11-0Then I did:./SetupSTM32CubeProgrammer-2.11.0.app/Cont...

MattKefford · 2022-08-15

Hi Pavel, further to your suggestion there is actually a macro CLEAR_REG which does the same as you suggested and removes the warning #define CLEAR_REG(REG) ((REG) = (0x0)) I also found a macro in the CRC header file which could be used too:...

User statistics

User Activity

Warning in HAL CRC since updating to F0 Cube v1.11.3

I2C - Send "Measurement Request" to HIH6130 IC

CubeIDE is unable to install the v1.6.1 update on macOS

VBUS sensing doesn't work because internal pull-up is activated during USB init rather than when connected - STM32F072

CubeIDE not switching context properly from CubeMX to C editor tab

Re: It is on my macOS not possible to install STM32CubeProgrammer (Big Sur 11.2.1) I get the notice that the file is damaged. I tried it several times?! What is happening?? I saw that in 2019, 2020, this problem often was mentioned? How come? Best Regards

Re: STM32H7 FDCAN FILTER

Re: STM32H7 FDCAN FILTER

Re: It is on my macOS not possible to install STM32CubeProgrammer (Big Sur 11.2.1) I get the notice that the file is damaged. I tried it several times?! What is happening?? I saw that in 2019, 2020, this problem often was mentioned? How come? Best Regards

Re: Warning in HAL CRC since updating to F0 Cube v1.11.3