Solved

HiI am having problems setting breakpoints when using the debugger in VS Code. I can step through manually but cannot seem to set breakpoints. Before starting to debug I can add a breakpoint at 50But when I run the code the breakpoint changes to a different line number outside of the loop line 54. Removed the target and reflashed in case the code is out of sync but do not understand. If I attempt to add a breakpoint in saysNew install (because 24.04 came out) but it did not work on the old install either.Thanks all - as ever

Hi,I know how to blink an led in Embedded C, but Currently I am trying to create an led blinking project using embedded C++ in stm32cubeide.So kindly give me some tips how to create it. IDE - STM32cubeide 1.15.0Development board - STM32F401VC discovery kit Thanks & RegardsSatyabrata Senapati(firmware Engineer) 

I have LL-API based UART/USART code which runs on an STM32U575 (tested on a NUCLEO-U575ZI-Q board), no problem (@ 115200).I would like to move this code to the LPUART (pins D0/D1, PG8/PG7, of the board).  However, I have failed; not even TX works (a probe connected to PG7/D1 shows low all the time when I transmit data on the LPUART).The changes I have made to my code are:Use the LL_LPUART_ functions instead of the LL_USART_ ones,Set AF8 for the pins,Use pin PG7 for TX (D1), PG8 for RX (D0),Call LL_APB3_GRP1_EnableClock().Select LL_RCC_LPUART1_CLKSOURCE_SYSCLK as the clock source for the LPUART (with LL_RCC_SetLPUARTClockSource()) so that it can achieve 115200.All configurations functions with a return value (e.g. LL_LPUART_Init()) returned success.  What have I missed?

Hello STMicroelectronics Community,I'm reaching out to you with a question regarding an SMD IC bearing the ST logo. I am in search of the datasheet for the IC labeled CCIC1I in the TSSOP28 package. Unfortunately, I couldn't find any information about this IC on the ST.com homepage. Where else could I look? Is the datasheet possibly restricted? Or do I need to contact a specific address?I require this data for repairing a projector and would greatly appreciate any assistance.Thank you in advance for your support!Best regards,Sven

Hi ST team,I have design the 10V isolated power supply design using viper222LSTR IC having universal input AC supply. Schematic of the circuit is attached here.When i am increasing the input voltage, voltage across the capacitor C7 maintain constant of 10V, while voltage across capacitor C12 is in increases, winding of the transformer, W3= W2= 30 turns, are same and W1= 180 turns. So why?1.  My voltage across the C12 is incases with increasing the input voltage.2. With increasing the dummy load (i.e. R8= 1K) then viper222 get on & off frequently.I have required constant 10V across C12 in isolated manner while increasing the input voltage ( I am extracted from C12 because of need of isolated power supply and and i want to avoid use of optocoupler in the circuit)       How i can fixed it, please help use.Thanks and Regards,Pemendra Pardhi  

Hi All,I found several topics with controversial information about what is this file used for?Like this:https://community.st.com/t5/stm32cubemx-mcus/what-is-the-mxproject-used-for/m-p/584042 I see in my file several sections [PreviousLibFiles][PreviousUsedKeilFiles][PreviousGenFiles] I don't see any critical information but not sure should I add it to commit or not?Thanks

Hi, Thew board was working fine until i tried to get serial working over virtual COM. I'm not sure what ive done but now im receiving this messageError in final launch sequence: Failed to execute MI command: load C:\\Users\\Ki\\STM32CubeIDE\\workspace_H503\\blink\\Debug\\blink.elf Error message from debugger back end: Error finishing flash operationIs there a way to reset the board? or have I bricked it. It still talks to the link utility in the IDE and says it needed an update which completed successfully.Sorry Im a bit lost and would appreciate some guidance. I can provide more info if neededThanks in advance  

Hi all and good time :hand_with_fingers_splayed:can U help me please?i'm confused about this part with the (UM smd code),i searched a lot on google and but i found only 2 parts with this smd code... (zener diode and tvs diode) !!:thinking_face:my first find --> zener diode Bzx84j-C5V6 SOD-323and next my find -->(TVS Diode) with part number (SMAJ15CA)i got crazy:face_with_rolling_eyes:.. which one should i choose????.i really need your help:eyes:T H A N K  YOU So sO So MUCH:folded_hands::smiling_face_with_heart_eyes:(mazie) 

I am working with the L051 chip and having issues with the CubeProgrammer Download..History:   we work with many of the STM32 chips.....and have for years, so well versed in this ...so this is an issue that we have not seen using any of the Tools... I wrote a test program, very simple toggle led....Set up the .IOC with FreertosProgram compiles just fine... as expected.....But this program is not the issue, using the Cube programmer is where the error comes in..Hardware setup....Custom board with STM32L051 chip.Using an FTDI USB  - TTL cable for programming PORTA100K pullups on the TX and RX as per AN2606BOOT1 pin pulled low, via 10K resistor for correct Boot config.Issues:We are able to connect to the chip in CubePrgmr just fine every time...In the TAB   Erasing and Programming:we load the   .ELF   file in to the prgmr and try to 'START PROGRAMMING'the download starts then:   See below:::10:41:02 : Memory Programming ...10:41:

Hello ,We are devloping application using NUCLEO-H503 , try to install USBX as CDC-ACM port and transfer data to host device ,1. Try to install Driver for USBX , but not found stmelectronics.xcube-azrtos-h5  How to use NUCLE-H503 USB in Device mode only as CDC-ACM port 

Hi guys,I want to know whether the device meets the 100Mbps full duplex need how to test?My own test is as follows:The device ip is 192.168.1.10, pc ip is 192.168.1.135.(The ip of pc is different in wireshark(135) and test software(25), because it is not the same pc and same test, just for your information)First of all, when connecting the device to PC via RJ45, the Ethernet link shows 100Mbps. I used the speed test software on PC, when sending arp, icmp, tcp, udp packets to the device at the same time, the device won't reply to some of the packets, especially not to ICMP packets.In this case, is the device considered to meet the 100 megabit full duplex? Or do all requests have to be replied by the device. 

Hello STM32 community,I've been examining the lsm303agr.h file from STMicroelectronics for the LSM303AGR accelerometer, and I came across something puzzling in line 197. In the code, it defines LSM303AGR_ACC_SENSITIVITY_2G as ((uint8_t)1), but according to the LSM303AGR datasheet, the linear acceleration sensitivity at ±2 g in normal mode is 3.9mg/LSB.Could someone help me understand why there's a discrepancy between the code definition and the datasheet specifications? I'm curious about the reasoning behind this difference and how it might impact the usage of the accelerometer in my project.Thank you in advance for any insights you can provide!

Hi, I am unable to interface with a sensor over RS485. I have a uart->RS485 converter hooked up to pins for USART1 (Tx on PD8, Rx on PD9) on a Nucleo-F439ZI.I also have a USBtoRS485 converter with which i'm able to communicate to the sensor fine. I have a scope connected onto the B- line and can compare the data.The sensor prescribes the following UART settings:Data bits: 8Number of stop bits: 1 bitParity: evenBaud rate (bps): 57600 (factory setting)and I have set USART1 t initialize with the following settings:huart1.Instance = USART1;huart1.Init.BaudRate = 57600;huart1.Init.WordLength = UART_WORDLENGTH_8B;huart1.Init.StopBits = UART_STOPBITS_1;huart1.Init.Parity = UART_PARITY_EVEN;huart1.Init.Mode = UART_MODE_TX_RX;huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;huart1.Init.OverSampling = UART_OVERSAMPLING_16; An image looks as can be seen in the attached scope3.jpg picture where RefA (grey) is the recorded (working) signal from the USBtoRS485 converter and CH1 (yellow) is t

When I hit Debug. System stops at first line of main() as intended. However no matter how I setup any breakpoints on the rest code, and hit Resume(F8) button. The code never stops on those breakpoint. even though I am 100% sure those breakpointed line code got run already. and if I hit suspend. the code stops normally. Also step into or over works normally. ( I am sure that the number of breakpoints I setup is less than 4) I checked log file of st link GDB server. I did not see any breakpoint setting command sent to the debugger via the SWD. Is this a software bug of CubeIDE? I saw some youtube video. it shows the breakpoint works fine. Could anyone give me some hint. I stuck on this issue for two days. :(

Im currently working on a custom PCB with cc1120 as transceiver and stm32f446RET6 as MCU. I integrate the cc1120 library from IT's library. The device uses SPI as serial communication. Here is the communication example in given datasheet. With this information i configured the SPI settings as:after that i use HAL_SPI_TransmitRecieve( ) function as my comm func. in driver. But im not gonna share the complex library instead i will demonstrate the situation. My CS pin and cc1120 reset pin is logic HIGH in idle by software.txdata[0] = 0x30; HAL_GPIO_WritePin(SPI1_CS_GPIO_Port, SPI1_CS_Pin, 0); HAL_SPI_TransmitReceive(&hspi1, txdata, rxdata, 1, 500); HAL_GPIO_WritePin(SPI1_CS_GPIO_Port, SPI1_CS_Pin, 1); /* USER CODE END 2 */ /* Infinite loop */ /* USER CODE BEGIN WHILE */ while (1) { txdata[0] = 0x2F; HAL_GPIO_WritePin(SPI1_CS_GPIO_Port, SPI1_CS_Pin, 0); HAL_SPI_TransmitReceive(&hspi1, txdata, rxdata, 1, 500); HAL_GPIO_WritePin(SPI1_CS_GPIO_Port, SPI1_CS_Pin, 1); HAL_D

HAL timebase set to use TIM6. ThreadX uses SysTick.My code is minimalistic for the test-project when debugging this issue. ThreadX is set up to have 1000 ticks/second as opposed to the default 100 ticks/second.I have one thread printing out HAL_GetTick() and _tx_time_get() after a tx_delay of 1000 milliseconds.HAL_GetTick as we all know returns uwTick, which gets incremented by the TIM6 interrupt callback.ThreadX returns the correct time, while GetTick() returns a value that gets incremented by about 15 for every 1000 ms. My only explanation for this is that ThreadX disables the interrupt that calls the TIM6 IncTick function while it does scheduling work in the background, but I have a hard time believing this as I can't find anyone else facing the same issue online.

I am trying to get a SPI port up and running on an STM32H745BI chip but after configuring the port and starting the transmission I never see any signals on the pins and the port never gets an End Of Transmission (EOT) high signal. Startup code is listed below, it hangs while waiting for EOT. Relevant register values are in the attached image. Any ideas on why this code doesn't work? Thanks!  // define GPIO pin interface to external ADC, see DS12923 Table 9 for alternate function mapping // Schematic signal static pinDef adc_rdl = { .port = GPIOI, .pin = PIN_0, .mode = Alternate, .type = PushPull, .speed = VeryHigh, .pull = None, .alternate = AF5 }; // SPI2_NSS static pinDef adc_sck = { .port = GPIOI, .pin = PIN_1, .mode = Alternate, .type = PushPull, .speed = VeryHigh, .pull = None, .alternate = AF5 }; // SPI2_SCK static pinDef adc_sdo = { .port = GPIOI, .pin = PIN_2, .mode = Alternate, .type = PushPull, .speed = VeryHigh, .pull = None, .alterna

Hi,I want to automatically add the following line of code at the top of each source file within my project:static char const thisFile[] = __FILE__;For this, I'm creating the following Define symbol (-D) in STM32CubeIDE, by going to project Properties -> C/C++ Build -> Settings -> Tool Settings -> MCU GCC Assembler -> Preprocessor:However, when I click on OK -> Apply and Close, it shows this warning, which I don't completely understand.Anyway, I click Rebuild Index, and it changes my symbol by removing the semicolon at the end and adding some new double quote symbol "and, when I build the project after this (the code already uses thisFile string in its functions), it throws this error:error: 'thisFile' undeclared (first use in this function)I suspect, that it happens because the preprocessor can't properly transform the semicolon from my symbol, so the whole static char const thisFile[] = __FILE__ line becomes invalid.Is there a way how to make this Define symbol (-D)

Hi all,I want to increment the lap_marker variable only once when the lap_button is pressed, but when I press the button, it increments multiple times, untill I let go of the button (when I put a breakpoint in the loop it works fine).I only want to increment once, Have I done something wrong? Is there another logic?The pin is PC13, in input mode and the internal pull-down resistor activated.Here is the code: //Read lap buttonif(HAL_GPIO_ReadPin(lap_button_GPIO_Port, lap_button_Pin)){lap_marker++;}

I want to control 6 axes using the default UART communication protocol for a motor driver using x-cube-mcsdk.How should I connect for 1:n communication?

Is the STM32CubeIDE defaults 64 bits in unix time?  if not, how/where to put gcc command line option in STM32CubeIDE "gcc -D_TIME_BITS=64".  Supposedly, this will redirect unix time to be 64 bit instead of traditional 32 bit that will overflow in year 2038.  TIA

Would appreciate pointer and insignt on learning how to do battery minimum energy LoRa on (a) half a dozen of sleep modes (b) example sequencer C coding with power saving  (c) reading list on application/tech notes, etc.  TIA

Hey, my question is how to add additional c source files to TouchGFX project so I can build project in TouchGFX Designer?I know I have to edit Makefile . I already tried it but with no success. Here is the code of my makefile:# Helper macros to convert spaces into question marks and back again e := sp := $(e) $(e) qs = $(subst ?,$(sp),$1) sq = $(subst $(sp),?,$1)   # Get name of this Makefile (avoid getting word 0 and a starting space) makefile_name := $(wordlist 1,1000,$(MAKEFILE_LIST))   # Get path of this Makefile makefile_path := $(call qs,$(dir $(call sq,$(abspath $(call sq,$(makefile_name))))))   # Get path where the Application is application_path := $(call qs,$(abspath $(call sq,$(makefile_path)../..)))   .PHONY: clean assets all   ifneq ($(words $(makefile_path))$(words $(MAKEFILE_LIST)),11) all clean assets: $(error Spaces not allowed in path) else   project_path := $(call qs,$(abspath $(call sq,$(makefile_path)../../..))) core_path := $(project

Hello,We are using ST25R3920B as NFC reader for our project. In order to implement the functionality we integrated the nfc RFAL driver provided from ST. We need to develop the software with respect to ASPICE guidelines. I would like to ask whether the RFAL lib of NFC Reader has been certified for ASPICE guidelines? https://www.st.com/en/embedded-software/stsw-st25rfal002.html

I bought a NUCLEO H755ZI board, but I can't make the LED connected to GPIOB pin 14 blink, neither with CMSIS nor with HAL, I saw some tutorials and questions here, but nothing solved it, thank you in advance for your help.