Solved

Hi everyone,been trying to nail the issue down for a while and I hope someone can helpI've got an LIS2DW12 connected using I2C to an STM32L476VGT6, and I'm trying to set it up to detect WAKEUPevents. I've been following ST's official AN5038 to get it in the right mode of operation.My steps are as follows, in pseudocode:On boot:on CTRL2 set .SOFT_RESET and write (0x40)wait 1 mson CTRL2 set .BOOT and write (0x80)wait 25 msread ALL_INT_SRC to clear any hanging interruptsTo set up:on CTRL2 set .BDU and .IF_ADD_INC and write (0x0C)on CTRL1 set .ODR to 25 Hz, .MODE to LOW_POWER, .LP_MODE to LP1 and write (0x30)on CTRL3 set .PP_OD to OPEN_DRAIND, .LIR to UNLATCHED, .H_ACTIVE to ACTIVE_LOW and write (0x38)on CTRL6 set .BW_FILT to ODR/2, .FS to 2g, .FDS to HIGH_PASS_PATH and .LOW_NOISE to TRUE and write (0x0C)on CTRL4 set .INT1_WU and write (0x20)on WAKE_UP_DUR set .WAKE_DUR to 2 and .SLEEP_DUR to 2 and write (0x42)on WAKE_UP_THS set .WK_THSx to 3 (90 mg @ 2 g range) and write (0x03)on CTRL7 se

HI,I'm a beginner. I should set up some STEVAL-MIC007V1 MEMS microphones. I have Nucleo-F401RE and X-Nucleo-AMICAM1. I have already downloaded the X-CUBE-MEMSMIC1 software package.Is it sufficient to install the UltrasoundFFT.exe executable or is it necessary to download additional software to use MEMS microphones?Thank you

Hi guys,I'm executing the "printf" in CubeIDE to output uint64_t with "%llu", but the printout is wrong.Why does it not support "%llu"?However it can work well in Keil. //debug.c int __io_putchar(int ch) //Redirect printf to uart { HAL_UART_Transmit(&huart1, (uint8_t *)&ch, 1, 0xFFFF); return (ch); } //main.c int main() { //*** printf("%llu\r\n", (uint64_t)1 ); //Hope to output "1", but output "lu" }    

Appreciate pointer to information.  New to these.  To power the STM32WL5EJC, we need to make a custom board incorporating the charging and protection circuit since 30mAh Li ion cell does not have build-in protection board.Appreciate circuit diagram, for or similar to, the popular Li ion cell charging board using TP4056 and protection chip DW01A.  Presumably, circuit need to auto switch cell in and out of circuit so the charger chip will end charging at 10% of current (3mA for 30mAh cell) going into the cell and not counting current feeding the STM32WLE5JC (6mA radio receive, 30mA radio transmit).We plan to use MCP1700, Linear LDO, to take Li ion cell 4.2V to 3.0V for STM32WLE5JC.   Many thanks  

Hi,I'd like to have a 2kHz clock source on PC9, I was wondering if I can use TIM3_CH4 or TIM8_CH4 to do it. May you please help me to figure out it? My question is how to generate a 2 kHz clock on PC9 if I would like to use TIM3_CH4 or TIM8_CH4? However, I can generate a clock with MCO2 function on PC9. I use the commend below, and I can get 5MHz clock if I used MCO2 on PC9.   RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;  RCC_OscInitStruct.HSEState = RCC_HSE_ON;  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;  RCC_OscInitStruct.PLL.PLLM = 25;  RCC_OscInitStruct.PLL.PLLN = 432;    RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;  RCC_OscInitStruct.PLL.PLLQ = 9;  RCC_OscInitStruct.PLL.PLLR = 7;HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_HSE, RCC_MCODIV_5);  Hope I can get the answer here, thank you.

I would like to know where the configuration set in STVP is stored.I'd like to set the configuration automatically, but I don't know where the default storage address is.  

Hey Everyone,  I am having an issue with the stm32h755 dual debugging. Im trying to run cm4 by itself without cm7. But the issue im having is, whenever I reset the MCU and check the SPI lines, I see a clock running. When I debug just cm4, I do not see the SPI clock at all. As if my Cm4 is not running on its own properly.  Is there a way I can debug just the cm4 inside the stm32h755? I did follow guides online, I have halt all cores unchecked, I setup the flashing correctly as well.  

Good morningI am a newbie about MCUs.I would like to begin with a STM32F446xC/E MCU and a led blinking small project.So, I need some help with basic topics.-Can I put the STM32F446xC/E on a breadboard?-Can I program the STM32F446xC/E with a Nucleo development board?Thanks to anyone willing to help.

I installed STM32CubeIDE 1.13.2 in the hope that the problem of the 1.13.1 release has been solved (see My old topic ) . Nothing the problem continues to exist. To make the integrated CubeMX work I have to open and close the IDE 3 or 4 times, also if it doesn't start I have to delete the home/user/workspace_1.13.2/.metadata directory. (for my system config see My old topic )Thanks for your help.Ferdinando

Hello,   I bought two EVLSPIN32G4-ACT motor control evaluation boards and tried to setup CAN-FD communication between them.   Then I came to know it doesn't have a CAN transceiver IC(U3) populated on board. Image attached for your reference.   Can anyone tell if someone faced the issue similar regarding this. ST Team please provide help and support through the hardware and CAN-FD functionality with this evaluation board.   Regards Yash B

Cant program STM32G031J4 with stm32CubeProgrammer 2.16.0 (bootloader 3.1). It display default flash size of 63Kb and all command have errors ( erase/read/write.....). 

Good day I am sending a CAN message from a STM32F042. The first two bytes are the value read from an ADC split into 2 bytes. Then just for testing I set 4 bytes to "F042" which is then a fixed value that i know its sending what I ask. The problem I have is no matter how i format the ADC value its never correct on the CAN BUS even though my RxData that i pass to can shows it is correct. Any value that I put into RxData that is fixed such as the F042 is always correct. I believe based on on the fact that I can fill all 8 bytes with fixed data like F042 and it always transmits as recieves correctly that my harware is good (My harness, a twisted pair cable with 120ohm termination, and both boards), for me that means it must be something in code of the F042 is going wrong. This is the section of code described above ADC_Select_CH4(); HAL_ADC_Start(&hadc); HAL_ADC_PollForConversion(&hadc, HAL_MAX_DELAY); HAL_ADC_Stop(&hadc); temp = HAL_ADC_GetValue(&hadc); remainder100

While "ST-LINK_gdbserver -d -v --frequency 1000 -cp ..." connects fine to STM32U083C-DK, NUCLEO-H7SL8 does not work.STMicroelectronics ST-LINK GDB server. Version 7.7.0Copyright (c) 2024, STMicroelectronics. All rights reserved.Starting server with the following options:Persistent Mode : DisabledLogging Level : 31Listen Port Number : 61234Status Refresh Delay : 15sVerbose Mode : EnabledSWD Debug : EnabledCOM frequency = 1000 kHzTarget connection mode: DefaultTarget connection failed. Try connecting under resetTarget connection failedTarget unknown error 32Error in initializing ST-LINK device.Reason: Unknown. Please check power and cabling to target. I lowered the frequency even much lower so frequency  should be no problem. StCubeProgrammer connects fine. Stlink firmware is from stsw-link007-v3-15-6.zipHas anybody success with this combination? Any hints?

- STM32G071R8T6, DMA chan 1 ADC's, DMA chan 2 SPI TX, DMA chan 3 SPI RX and DMA chan 4 DAC- Tested the SPI configuration without the DMA to a SPI EEPROM and it works.    Once the DMA configuration was used, we do not see any data being transmitted.     The initial DMA based communication to the EEPROM is a read command, address and then 0x55 data so that we clock the EEPROMs response back. The Chip Select to the EEPROM is done manually. Because the initial testing done wrote directly to the SPI registers, it seems like something in the configuration of DMA to SPI is not correct. We have used the STM32Cube Repository version STM32Cube_FW_G0_V1.6.1 for Low Level examples but the DMA and SPI are not tired together for the G071(they have HAL based.)- If we remove the call to LL_DMAMUX_SetRequestID(), which is needed because the G071 has a DMA mux, we will receive a DMA1_Channel2_3_IRQHandler interrupt after the TX DMA is triggered. There is still no data

ACI_L2CAP_CONNECTION_UPDATE_RESP_EVENTWhat is the Result field?  Need to know if change accepted

About the board NUCLEO F446REIs it possie, with that board, and for learning purpose, to drive external devices such servomotors?If so, how are they connected to the board?Thanks

I'm planning a new device and wish to use an STM32U5 series processor.We would like to reuse an existing display.  However, this has a QSPI interface (at 50MHz).Is it possible to use one of the Octal-SPI interfaces on the STM32U5 series for driving a display?  I could not find any documentation explicitly discussing this.Specifically I was looking at the STM32U585Thanks!

After updating to STM32CubeIDE 1.13.2, and updating my workspace, I'm suddenly getting warnings when compiling the STM32_WPAN SHCI library, followed by a handful of linker errors. The warnings are all in `shci.c` and look like this: Project/Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/shci/shci.c: In function 'SHCI_C2_FUS_GetState': Project/Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/shci/shci.c:57:98: warning: array subscript 'TL_CcEvt_t[0]' is partly outside array bounds of 'uint8_t[16]' {aka 'unsigned char[16]'} [-Warray-bounds] 57 | *p_error_code = (SHCI_FUS_GetState_ErrorCode_t)(((TL_CcEvt_t*)(p_rsp->evtserial.evt.payload))->payload[1]); | ^~ Project/Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/shci/shci.c:45:11: note: while referencing 'local_buffer' 45 | uint8_t local_buffer[TL_BLEEVT_CS_BUFFER_SIZE + 1]; | ^~~~~~~~~~~~  The linker errors look like this: C:/ST/STM32CubeIDE_1.6.1/STM32CubeIDE/plugins/com.st.stm3

HiI got this problem where I got an MCP2515 that wants an ISP type signal, and then converts it to CAN. I am only familier with the CAN protocol and the HAL library, so is there an easy way to make the STM32 convert the code from CAN to ISP?

Hello!   I am working on a project where I would like to be able to detect which type of sensor I have connected (via I2C). For example, I am currentky planning on using a VL53L0x, but would like to be able to detect on boot if I am still using the VL53L0x or have switched to a VL53L1Cx, etc. I recognize that the initialization and read processes are a bit different, and would simply set a flag so I know which to call. Basically, I would like to be able to swap sensors in the field and be able to detect those changes. Is there any sort of ID Register? Is there a different way? I looked through the VL53L0x data sheet but did not find any mention of anything like this. Thanks!

The STM32 families typically use Quad-SPI for executable external flash, from my research (ref)But the only H-Series options with Quad-SPI are expensive! Are there any alternative methods to executable external program space?   

I have a problem in my project involving the STM32L010RB MCU and the HC05 Bluetooth module.Currently, the system operates smoothly when connected to the USB port. The HC05 Bluetooth module successfully performs its data transmission and reception tasks without any hitches. However, upon introducing an external battery and jumpering pins 2 and 3 on JP5 to provide the Bluetooth module with a 5-volt supply, the module appears to power up correctly, as indicated by the LED, but fails to transmit or receive any data.I have thoroughly reviewed the connections and power supply, but I have been unable to identify the root cause of this issue.

I am trying to enable all 3 UARTS (LPUART, USART1 and USART2) within the STM IDE. However, on choosing LPUART, USARTS2 become unavailable (and vice versa) . Is this a device limitation?   We really would like to be able to use all 3 uarts (no flow control necessary)

hear i used the two wave files. but hear the logic is 2 wav files at continues memory location but I want  different location wave files to play using the  code logic.

Hi All.​​Does anyone know about a simple sample code to drive bldc motor with sinusoidal control? ​I only want to know the way how to setting PWM and update the PWM output.​MCSDK’s output sample code is hard to use and understand, it take time. ​Something like the device peripheral sample code will suffice.