About TFlac

TFlac · 2019-10-11

I have a fundamental situation I think we all in the ST Community should be concerned about and want to make better as we go forward. I have been working with the STM32 solution for about 4 months now, and making it my mission to learn and stay with ...

TFlac · 2019-09-24

I am using STM32CubeMX, STM32CubeIDE and val board STM32F303RE. All I wish to do is recreate the project/examples with the firmware package using CUBEMX and CUBE_IDE combo.I have been able to get the Examples to work but not as the documents explain....

TFlac · 2019-09-13

I have a design where I am trying to calculate the frequency of an incoming signal. I am using STM32CubeMX and STM32CubeIDE combo. My process is to use "Live Expressions' within DEBUG to see the results. My platform is STM32F303RE. The code clip bel...

TFlac · 2019-09-09

Hello ST Commun,I have completed a design using STM32CubeF3 and SW4STM32 with Eval board STM32F303RE. The design is done, I was able to build now I'm in DEBUG. To value my variables I am using STM Studio. I load my elf file and proceed to select the ...

TFlac · 2019-09-05

I have completed a design using STM32F303RE Nucleo-64 board. Using STM32CubeMX and SW4STM32 (IDE). My design is done, I have build the design and there are no errors. Now I'm ready to physically download and test the design. I realize one of the PINS...

TFlac · 2019-10-16

Hi Amel,This is good news. I do have an Eval board for STM32G files and I will surely look at the .ioc file you have suggested. Thanks you so much for your feedback, this is a good response and I'm sure ST is working hard to bring updated material to...

TFlac · 2019-10-14

Thanks for this update. Since my last request I have been trying to fool the tools again. I went into edit a couple of H-files and noted, there is no sacred USER space within the H-files. No matter what you do the H-Files get edited via CubeMX.I wond...

TFlac · 2019-10-14

Thanks for this update. Since my last request I have been trying to fool the tools again. I went into edit a couple of H-files and noted, there is no sacred USER space within the H-files. No matter what you do the H-Files get edited via CubeMX.I wond...

TFlac · 2019-10-11

Well, can't be 10% sure what is wrong, I will say that Windows 7 functions fine. One thing to note, your system has to be 64bit machine - I'm sure it is to run Windows 10. I loaded the Nucleo drivers on my computer with no problem. The next question ...

TFlac · 2019-09-25

Hi Member,You would use the NUCLEO-F103RB board. This assumes you will use the CubeMX and CubeIDE flow. Here you will be able to complete your design and transfer to you final board. The good news is all of the schematics are provided and from here i...

User statistics

User Activity

I have a fundamental situation I think we all in the ST Community should be concerned

Has anyone open a Project/Example under STM32_FW_F3 yet.

Cannot get "Live Expression" to show results in CubeIDE, there are no compile errors.

I am using STM Studio and my variables don't have addresses.

I have a completed design in software via STM32Cube and SW4STM32. I need to change a PIN in CubeMX. What will happen with my finished code when I GENERATE CODE within MX with the new single PIN change?

Re: I have a fundamental situation I think we all in the ST Community should be concerned

Re: I have a fundamental situation I think we all in the ST Community should be concerned

Re: I have a fundamental situation I think we all in the ST Community should be concerned

Re: Unable to install driver for STM32 nucleo board in windows 10

Re: Which Nucleo board to be used for STM32F103RE & STM32F103VE microcontrollers?