About NEdom.1

NEdom.1 · 2024-11-18

I am trying to use STM32L431RCT6 with STM32CubeIDE and STM32Cube_FW_L4_V1.18.1 for a low power mode application. I tried Sleep mode, Stop mode and they both work OK. But the standby mode does not working. The MCU wakes up instantly after entering sta...

NEdom.1 · 2024-11-01

I started to use this stlink v3set since year 2023. All works well until recently it get offline and reconnected immediately sometimes. The red light flashes several times then stays on after connect to USB. The STLINK_V3S disk is opened in an explor...

NEdom.1 · 2023-10-29

I am using STM32F103RCTx and STM32CubeIDE for developing a small application.I am tuning a vacuum pump DC motor using PWM signal with TIM1 CHANNEL_1. But I hit a small problem when I start debug the board. The motor is running from the time the IDE s...

NEdom.1 · 2021-11-16

With STM32CubeIDE and freeRTOS for STM32F429 chips, the IDE generate code using freeRTOS V10.3.1. I could setup heap5 with SDRAM enabled and won't be affected by later regenerating code when changing .ioc file. The cmsis_os2.c file works fine. Both t...

NEdom.1 · 2021-04-27

I have been using STM32CubeIDE for quite some time. It's a great tool. How ever, I have been experiencing a bug in project settings since I updated to 1.6.1.Usually, I put my code in a separate folder, thus I could build up a project using existing c...

NEdom.1 · 2024-11-18

I reconfig the clock, the HSE and LSE. After generating the code and flashing, the standby mode is activated.Try to change HSE and LSE back, or several compositions. Things goes normal.Try to add back FreeRTOS. All is good.Very strange STM32CubeIDE b...

NEdom.1 · 2024-11-18

Thanks Andrew.The HAL_SuspendTick() and HAL_ResumeTick() are used with SLEEP Mode and STOP Mode functions and work well. In STANDBY Mode, it is like the MCU being Reset then start on with only RTC information and some backup registers preserved.The s...

NEdom.1 · 2024-11-18

Thank you, Andrew.Finally, I got the problems fixed by re-plug the USB connectors.The target is on low power mode and I press and hold down the reset button while starting flashing. But due to the reliability USB connections, just got some luck on su...

NEdom.1 · 2023-10-31

Thanks for reply. I do use the HAL functions to control PWM signal. The board runs normally by itself. What bothers me is that when I am debugging the board.

NEdom.1 · 2023-10-31

Thanks for sharing the info of MCU's reset states.The motor runs when I am holding reset button. The PWM pin output 2.33V when RESET pin is low. Maybe I need to add some extra circuit to make it work.

User statistics

User Activity

STM32L431RCT6 wakes up immediately after standby

ST link v3set unable to recognize anything after connected to USB

STM32 series PWM out logic level at reset and pause state

Request update of freeRTOS version for STM32F103ZE with STM32CubeIDE

Bug on STM32CubeIDE at Project->Properties->C/C++ General->Paths and Symbols

Re: STM32L431RCT6 wakes up immediately after standby

Re: STM32L431RCT6 wakes up immediately after standby

Re: ST link v3set unable to recognize anything after connected to USB

Re: STM32 series PWM out logic level at reset and pause state

Re: STM32 series PWM out logic level at reset and pause state