Solved

Posted on February 28, 2017 at 15:47Hi, when I create a new project in SPC5 studio, its not showing me with the component initialization options. It does not present me with any options for choosing the microcontroller, configuring the clocks, etc. Please see the attached picture(SPC5)When I select the microcontroller using the pin map wizard, I am able to configure pins, but it does not seem to be generating any application code.  Please see the attached picture( SPC5_pinmap)Also, what is the latest released version of SPC5 studio? I have seen post here mentioning the version 5.2.3 being available. My application is still on version 5.0. Its showing 'no updates found in the available software sites' when checking for updates.#spc5-studio

Posted on February 28, 2017 at 16:56Hi, I'm setting up SPI comms with a slave device. (ADXL350 accelerometer) This is on an STM32F767ZIT6. I should point out I put this on a nucleo -'F746 board but it's all working fine so far at 200MHz with other peripherals presenting no problem.I've selected 8 bit data size, but am seeing 16 clocks on a scope. I use a read function to read address 0x00, the device's ''who_am_I'' register, and get 0xE5 back. In theory this is ok.However, I see the image here:Yellow = MOSICyan = MISORed = CLKGreen = _CSThe accelerometer is replying <0xE5> 3 times (trace 2 in cyan) because of this 16bit data size. If I set it to 4bit data size, I get 8 data clocks. But then I get a nybble in the low byte and a nybble in the high byte.https://community.st.com/0D50X00009XkeupSABhttp://www.st.com/content/ccc/resource/technical/document/technical_note/58/17/ad/50/fa/c9/48/07/DM00054618.pdf/files/DM00054618.pdf/jcr:content/translations/en.DM00054618.pdf. I use m

Posted on March 01, 2017 at 17:07Hi I have a custom bootloader that I flash to the first sector (0x8000000)  and when it receives a new program it loads it to 0x8003000. I can jumps to the user application,however  when It from user application jumps to the bootloader it seems to have problems because i can't display the menu in hyper terminal (send data via USART),but i can blink a led .Do you have any idea ?Thank you in advance !Turvey.Clive.002#custom-bootloader #stm32f1

Posted on March 02, 2017 at 08:49Hello,I am working on STM32F302RC. I want to use the USART1 with parity enabled both odd/even which is configurable through command.I am using USART1 withbaudrate 115200,data length8 bit ,  parity none with this configuration it works fine. stop bit   1,When I change the configuration of USART1 to odd or even parity it doesn't work I get junk character on serial termina  as shown below.sƒß2ØL<DC3> ›'š­ÚšQM¸·»'¹bé·-Hl?S<RS> <DC2> å¹7™JC1<SUB> œî<SO> ƒÃé4 ]\V<SYN> åßóöX-<ETX> ‚, Ø-Hl<HT> <HT> c<STX> �?<CR>Š Rn-EEº�£{Zª^<SYN> kênæzVH<FF>•åÓIâQ7$<DC4> <SI> KUad¨�?ËégC1¨Ên-EEº�£{Zª^<SYN> kênæzVH<FF>•åÓIâQ7$<DC4> <SI> KUad¨�?ËégC1¨Ên-EEº�£{Zª^<SYN> kênæzVH<FF>•åÓIâQ7$<DC4> <SI> KUad¨�?ËégC1¨Ü]N<ETX> š�?éô<-Rë�•m ._<SYN> å ÔLJHüWhat could be the issue? Kindly suggest.Thank you.

Posted on February 28, 2017 at 16:221:I have developed a small program for the STM32L031 Nucleo-32 using the example UART_TwoBoards_ComIT. The program run on the STM32L031 Nucleo-32 develop-board. When I load* the program to our own HW it does not start, I have tried with and without the compiler directive USE_STM32L0XX_NUCLEO_32. I suspect the system clock generation, but can’t find where it is setup.*I load the program using STM flash_loader_demo_v2.8.0.2:I want to use the ST-LINK V2 for debug should the data port be connected to PA13?Do any have a hint or comments that could help me?-Mads

Posted on December 05, 2016 at 21:23I use CubeMX on maxOS to generate projects for SW4STM32 then run a https://github.com/baoshi/CubeMX2Makefile to generate a Makefile for the gnu gcc toolchain. This worked fine on MX 4.16 and 4.17 but it broke today when I installed to 4.18. I tracked it down to four missing " entities in .cprofile where it defines the C preprocessor values.The incorrect line generated by MX is:<option id='gnu.c.compiler.option.preprocessor.def.symbols.1056679357' name='Defined symbols (-D)' superClass='gnu.c.compiler.option.preprocessor.def.symbols' useByScannerDiscovery='false' valueType='definedSymbols'><listOptionValue builtIn='false' value='__weak=__attribute__((weak))' /><listOptionValue builtIn='false' value='__packed=__attribute__((__packed__))' /><listOptionValue builtIn='false' value='USE_HAL_DRIVER' /><listOptionValue builtIn='false' value='STM32F446xx' /></option>But it should be:<option

Posted on March 01, 2017 at 16:29I'm working with STM32L475 and I'm using LPTIM to create a PWM signal. LSE clock is used (because I will use Stop mode), and period is set to 31 in ordet to generate 1kHz signal. PWM is working fine and dutycycle is modified according to the pulse value I set to the 'HAL_LPTIM_PWM_Start' function. Nevertheless, when I try to set PWM signal to 100% or 0%, the output signal looks similar to the one I have when dutycycle is set to 99% or 1%. Do you know why I get such behaviour?#lptim #stm32l4 #pwm

Posted on March 01, 2017 at 15:27Hi,Here is my code for configuring two different usart but my USART3 doesn't work properly and USART2 works fine.(I remap both of them). what is my mistake that I didn't pay attention?Problem: I don't have any signal on USART3_TX pin when I send a char. however my USART1 works fine(send and receive)    USART_InitTypeDef USARTConfiguration;    GPIO_InitTypeDef GPIOS;        RCC_APB2PeriphClockCmd(RCC_APB1Periph_USART2|RCC_APB1Periph_USART3|RCC_APB2Periph_GPIOD |RCC_APB2Periph_GPIOC |RCC_APB2Periph_AFIO,ENABLE); GPIO_PinRemapConfig(GPIO_Remap_USART2|GPIO_PartialRemap_USART3,ENABLE);        GPIOS.GPIO_Mode=GPIO_Mode_AF_PP ;    GPIOS.GPIO_Speed=GPIO_Speed_50MHz;    GPIOS.GPIO_Pin=GPIO_Pin_5;    GPIO_Init(GPIOD,&GPIOS);        GPIOS.GPIO_Mode=GPIO_Mode_IN_FLOATING ;    GP

Posted on February 28, 2017 at 01:00HiCubeMX generates in usbd_conf.h:#define USBD_DFU_XFER_SIZE 1024This is the reported transfer size also for tools like dfu-util'Device returned transfer size 1024'But the size of pages of the flash is 2048 bytes for this device.When download firmware.bin by this so configured interface any page gets erased againafter the first 1024 bytes are written. So in the end from any 2k flash page only the upper halfis written, The lower half contains FFFFFF....#define USBD_DFU_XFER_SIZE 2048makes the thing work for me.Dieter

Posted on February 14, 2017 at 21:39I've read through AN4767, AN4808 and several others. I think I understand how nBFB2 can cause BANK 2 to be addressed as 0x0800000 & BANK1 aliases to 0x0804000 (L152 has 512K, so 2x256k banks). First a great shout-out to Turvey.Clive.002 http://userbadge, who makes the forum worth searching & asking at :-]. Hope you get a pay raise this year & every year!My remaining questions:1) Does this swap also affect EEPROM? AN4808 (& others) say code running in BANK1 should use EEPROM BANK2, and vis-vera since the banks share HW controllers & this allows code to run/read while writing EEPROM. So are the EEPROM banks swapped as well, or should the 'aliased' image at 0x08000000 always use EEPROM BANK2 as-if code was BANK1?2) The 'Ping-Pong' effect - someone else asked this, but wasn't directly answered.2a) I understand if I start running my FWv1 in HW-BANK1 & HW-BANK2 empty (BFB2 can be anything). So field upgrade to FWv2 means I copy to

Posted on February 28, 2017 at 10:48hello AllI have question about internal trigger connection.I use stm32f405 and accordingly document RM0090 (reference manual) table 100 page 660 the TIM12 can be slave of the TIM14.But TIM14 does not have TIM_CR2 register which contains MMS(Master Mode Selection) bits to select the the source of synchronization (Update or other).So how to join two timers TIM14 and TIM12 as master slave coupleThanks .

Posted on February 24, 2017 at 14:10We need layout files of X-NUCLEO-IDW01M1

Posted on February 27, 2017 at 23:45I want to flash a load on the STM32F0CB using the STM Flash Loader demo. My configuration is: 57600, Data Bits:8, Parity: Even, Echo: Disabled, Timeout: 10.I also tried with parities Odd and None.After resetting the MCU, I get the error: 'Cannot get available commands, Please, Try to change Echo selection, Reset your device then try again...'. I changed the Echo selection mode with the same bad result.So I tested with serial tool. First of all, the only baud rates which gave a valid reply (ACK: 0x79, NACK: 0x1F)  were 56000 and 57600. So I sent the 'login' command 0x7F and got the expected 0x79 reply (ACK). Good! The MCU is in the booloader! Then I sent a Get command (0x00 0xFF) and didn't get any reply. I sent the same command again and I got a NACK (0x1F) reply. These are the two only cases I can get alternatively. If a enter 0x7F, I get the same behaviour, the same two cases so it means the MCU di

Posted on February 27, 2017 at 10:31I'm using SPC5Studio 5.2.2 and got a notification about available updates. I tried to update, but got this problem:An error occurred while collecting items to be installedsession context was:(profile=profile, phase=org.eclipse.equinox.internal.p2.engine.phases.Collect, operand=, action=).Artifact not found: http://spc5.drive.cloudforge.com/projects/spc5releases/SPC5Studio/updates5/plugins/com.st.tools.spc5.components.platform.spc570sxx_1.0.0.201702151735.jar.http://spc5.drive.cloudforge.com/projects/spc5releases/SPC5Studio/updates5/plugins/com.st.tools.spc5.components.platform.spc570sxx_1.0.0.201702151735.jar#spc5studio #updates #spc5-studio #update

Posted on February 24, 2017 at 17:51hey,I tried to run usb hs + vcp with code created by CubeMX.In generated code i have changed:#define APP_RX_DATA_SIZE 64#define APP_TX_DATA_SIZE 64and included in main.c:#include 'usbd_cdc_if.h'also changed:Stack_Size EQU     0x00004000Heap_Size      EQU     0x00002000and no luck at all. When pluging in usb cable i got message in linux:usb 1-1: new full-speed USB device number 80 using xhci_hcdusb 1-1: device descriptor read/64, error -71usb 1-1: device descriptor read/64, error -71usb 1-1: new full-speed USB device number 81 using xhci_hcdusb 1-1: device descriptor read/64, error -71usb 1-1: device descriptor read/64, error -71usb 1-1: new full-speed USB device number 82 using xhci_hcdusb 1-1: Device not responding to setup address.usb 1-1: Device not responding to setup address.usb 1-1: device not accepting address 82, error -71usb 1-1: new full-speed USB device number 83 using xhci_hcdusb 1-1: Device not re

Posted on February 27, 2017 at 06:38I have a problem.the problem is please install truestudio toolchain to open the project or associate the file type of the project with your toolchain in system default program settings.i don't know how can i solve it.so i want solve it.

Posted on February 18, 2017 at 00:48Hi,My BlueNRG-MS, running 7.2c, acts both as a central and a peripheral (mode 4). How should I select the advertizing min and max intervals for the peripheral as well as the connection min and max intervals for the central? There seem to be a relationship between them, but I'm not sure I understand it.I'm trying to get the minimal connection interval for the central role, while ensuring proper connectivity for the peripheral.LE_Scan_Interval and LE_Scan_Window seems also to come into play...Right now, I'm testing different values through trial and error, but if there is a mathematical relationship between those, I'd like to know it.Thanks!#bluenrg-ms

Posted on January 21, 2017 at 13:33Hey guys,I created 2 sets of projects with CubeMX for my STM32F429I-Disc 1 board.I project is a Device HID project, the other one is a Device Custom HID project.The Device HID projects works fine, the Custom HID project compiles correctly but will not flash onto my MCU.I'm aware that for the custom HID USB routine to actually work, i'll have to adjust the USB descriptors. I have not done this yet!However this problem looks like more severe problem to me. Is there something wrong with the cube MX code generation?The log of the failed Custom HID looks like thisOpen On-Chip Debugger 0.10.0-dev-00267-g884c33c (2016-03-16-12:22)Licensed under GNU GPL v2For bug reports, read    https://community.st.com/external-link.jspa?url=http%3A%2F%2Fopenocd.org%2Fdoc%2Fdoxygen%2Fbugs.htmlInfo : auto-selecting first available session transport 'hla_swd'. To override use 'transport select <transport>'.Info : The selected transport took over low-leve

Posted on February 24, 2017 at 06:55 Hi, I recently brought up the I2C using the STM32CubeMx(4.0) and STM32CUBE_FW_L4_v1.6.0 and I was attempting to write to a slave device with an address of 0x2A. I noticed that my slave device was NACK-ing back. Upon further inspection, it looks as if the address is shifted to the right by 1-bit, resulting in an address of 0x15 when transmitted on the line. To test this theory out, I purposefully used an address that is shifted 1-bit to the left: 0x Doing so registered an address of 0x2A on the physical bus which then I was able to hit the register with some data. I couldn't find any literature that required me to shift my I2C address left by 1-bit to have it address correctly. Has anyone else run into this issue? My solution is a work around but I would like to understand the root cause of this issue; whether I introduced it or possibly an inherent issue with the HAL drivers? Thanks!! Slave Address: //#define I2C_ADDRESS0x2A #defi

Posted on February 25, 2017 at 04:22Hi,I'm using a STM32F303 (landing page: http://www.st.com/en/microcontrollers/stm32f303k8.html) for one of my project. I have PA0 configured as a GPIO output with push pull used to turn ON/OFF a BJT. I also have PA3 configured to use the ADC1 channel 4 module.When I set PA0 high, the ADC readings increase by about 1.8V. When it is low, the readings are correct. Why does this happen? Externally, these two pins aren't connected directly to each other.

Posted on February 23, 2017 at 16:21I try to write to a characteristic on a remote device, BlueNRG-MS works as peripheral client. I call aci_gatt_write_charac_value() and it returns SUCCESS. But then EVT_BLUE_GATT_PROCEDURE_COMPLETE comes and it is sometimes 0x00 (BLE_STATUS_SUCCESS) and sometimes it's 0x41 (BLE_STATUS_FAILED). What could be the reason and how to solve this? Stack is 7.2.c.#ancs #iphone #ble #bluenrg-ms #client

Posted on February 23, 2017 at 00:41i cant download STM32CubeL4 Some time it starts and the download chokes in the middle otherwise it dosen't start

Posted on January 04, 2017 at 00:01 Hi,I am working  on an application on an STM32F303RET6 on a nucleo board. I am struggling to get DMA working on USART1 Rx.  I can successfully enable the USART port and it works correctly with the receive interrupt but once I enable the DMA it no longer works. I did have this code working on a STM32F103 nucleo board before but can't for the life of me get it to wrk on the F3 board. I don't have access t my code currently so will edit and add the it later.Is there anything different about the F3 chip compared to then F1 that might catch me out?Thanks in advance.Edit: code below. Hopefully its sufficiently readable.#define USART_SBUS USART1#define USART_SBUS_GPIO GPIOC#define USART_SBUS_CLK RCC_APB2Periph_USART1#define USART_SBUS_GPIO_CLK RCC_AHBPeriph_GPIOC#define USART_SBUS_RX_PIN GPIO_Pin_5#define USART_SBUS_RX_PIN_SOURCE GPIO_PinSource5#define USART_SBUS_RX_DMA_CHANNEL DMA1_Channel5#define DMA_SBUS_IRQN DMA1_Channel5_

Posted on February 24, 2017 at 13:40For a new IoT proof-of-concept (PoC) I shortly start I need to measure some parameters like e.g. temperature in a building environment (building can be broad interpreted: an office building, a hospital, etc.). After some investigation I think an option would be using Sub 1GHz for connectivity. My questions:- Would indeed Sub 1GHz be a viable option for these kinds of use cases?- Or, are there better alternatives? - For our PoC what devkits/components (a few edge device kits + a gateway device to connect the edge devices to the Internet/CLoud), as a result of my 2 previous questions, can we best use?Thanks.#sub-1ghz-nucleo #stm32 #nucleo #wireless

Posted on February 23, 2017 at 04:59I have X-NUCLEO-IHM02A1 expansion board.And downloaded the its firmware file of X-CUBE-SPN2.The file can not be unzipped.Please check the zip file and upload latest one as soon as possible.thanks