About PPate.2

PPate.2 · 2024-06-26

Hello,I have STSPIN32F0 Based Board for PMSM motor Drive. This Motor Works for Water Pump Application. we have Created 5 step in start up sequence using MC workbench. Motor Rotate as per Profile upto start up sequence Complete. But as soon as Motor ...

PPate.2 · 2024-05-30

Hello,we have STSPIN32F0601 based custom designed board for PMSM motor Controller. we have generated FOC code using MC workbench and it works ok.Now we want to use ACIM motor in this Hardware (with Little change or No change in Hardware). we are una...

PPate.2 · 2024-03-29

Hello , I have STSPIN32F0251 Development Board. In that board schematic we have found PA0_B Label that is connected default to Pin No 12 (PA0) of MCU(STSPIN32F251) .we want to know the importance and reason of connecting it. also where in firmware co...

PPate.2 · 2024-03-28

Hello,I have STSPIN32F0 Based Board for PMSM motor Drive. This Motor Works for Water Pump Application. we have Created 5 step in start up sequence using MC workbench. Motor Rotate as per Profile upto start up sequence Complete. But as soon as Motor ...

PPate.2 · 2024-02-18

Hello,I have STSPIN32F0 Based Board for PMSM motor Drive. This Motor Works for Water Pump Application. we have Created 5 step in start up sequence using MC workbench. Motor Rotate as per Profile upto start up sequence Complete. But as soon as Motor ...

PPate.2 · 2024-07-03

Hello sir,I am using motor in Torque Control mode.Can you please guide me that how can I lower torque during open to close loop transition. How can i know that which is Optimal value of Torque that could give a best performance.Here i have attached m...

PPate.2 · 2024-05-30

thanks for your Prompt Reply,we have tried generating code for ACIM using MC workbench and selecting NUCLEO-G431RB board. But we don't have any idea what we have to change in code to make it work with STSPIN32F0601. Can you guide us in detail or shar...

PPate.2 · 2024-03-29

Hello sir,Thanks for your reply,It's Our Bed Luck that all things Works Very Fine in Our Factory Conditions. Problem starts only in Field Condition as i mentioned above some field parameters are not in our Control.So what we have Observed till is whe...

PPate.2 · 2024-03-29

Hello sir"speed feedback error occur as soon as the system try to close the loop " in most of the cases.in some cases(about 1 % cases) motor runs at max speed for some duration like 10 minutes and then Speed Feedback error comes.Thanks

PPate.2 · 2024-03-29

Hello Sir,Thanks for your Reply, Our Application is water Pump. in that case we require maximum Torque to get maximum water flow.Is there any example code that will operate in Open Loop for STSPIN32F0601 MCU ?In Our Current Code we are facing proble...

User statistics

User Activity

STSPIN32F0601 BASED MOTOR CONTROL ACCELERATIONA AND DEACCELERATION CODING

STSPIn32F0601 based ACIM motor Control

EVSPIN32F0251 board PA0 Pin Use

STSPIN based Motor Controller acceleration and deacceleration setting in Torque Control

STSPIN32F0 Series motor Controller Acceleration and Deacceleration settings

Re: STSPIN32F0601 BASED MOTOR CONTROL ACCELERATIONA AND DEACCELERATION CODING

Re: STSPIn32F0601 based ACIM motor Control

Re: STSPIN based Motor Controller acceleration and deacceleration setting in Torque Control

Re: STSPIN based Motor Controller acceleration and deacceleration setting in Torque Control

Re: STSPIN based Motor Controller acceleration and deacceleration setting in Torque Control