About JMene.1

JMene.1 · 2024-02-09

Hello,In the past 2 days, I have an errorwhen I launch the debugger and it looks the issue comes from eclipse. When I launched the debuger, I have this error window.I uninstalled CubeIDE, and installed it again (tried 3 different versions).I can dow...

JMene.1 · 2023-05-16

JMene.1 · 2022-04-28

JMene.1 · 2022-02-01

JMene.1 · 2021-10-01

JMene.1 · 2022-03-15

Thanks. But there is a way to do it easely with the cubeIDE or I need to change the makefile?

JMene.1 · 2021-09-15

Thanks Houda. The answer is yes to both questions.

JMene.1 · 2021-03-17

I tried with cubeIDE and Keil.If I write the code below, bit 16 is set and not bit 17. *((uint32_t *) 0x40007C08) = 1<<16 | 1<<17; value = *((uint32_t *) 0x40007C08);I tried to set ICx bits and ICOS bits first too, but nothing changed. bit17 is the o...

JMene.1 · 2021-03-16

Imen, the input capture works correctly. My problem is the ICR register of the RI peripheral. When, with the debug, I try to set bit 17 and 16 to 1 in order to Timer4, I get an error: value out of range. Can I route PC13 to the Timer 4 IC2?Thanks

JMene.1 · 2020-10-21

Thanks for the tip. Yes I checked and the AFR was not configured correctly. I use the STM32CubeIDE to initialize the ports. When I use PD2 to connect to TIM3_ETR, everything is configured correctly. When I use PA0 to connect to TIM2_ETR, the AFR regi...

User statistics

User Activity

Error when debugging with assembly window offset -> length

I use the Nucleo-L152 and if I remove the jumper 6 and jumper 5, I get a voltage between +3V3 and VDD of 2.5V and a current of 750uA. Can you explain where this voltage and current are coming from?

In the cubeIDE, I use the Data Trace Timeline Graph (that works perfectly) but I would like to change the colors of the curves. I don't find any configuration to change these colors. is it possible? if yes how?

If I programmed a region of Flash protected by PCROP., how I can I modify the rest of the code, download and debug it with the STM32CubeIDE? In other words, is it possible to download code only in Bank1 and nothing in Bank2, hence keeping the PCROP region

I use NucleoL152RE with interrupt on PC13. Checking the ISER in the SFR, I have the address 0xE000E004 but the base address is 0xE000E100. When I check in the memory browser at 0xE000E104, I get the right ISER value. Thanks to confirm the bug of cubeIDE

Re: If I programmed a region of Flash protected by PCROP., how I can I modify the rest of the code, download and debug it with the STM32CubeIDE? In other words, is it possible to download code only in Bank1 and nothing in Bank2, hence keeping the PCROP region

Re: I'm using the NUCELO-L152 and I want to sept the WRP bits with the cube programmer. When I set a bit and click on apply, I get the error message: "option Byte WRP does not exist". What is the process to set the WRP bits with the cube programmer?

Re: I'm using theNucleo STM32L152 and I want to remap PC13 on timer 4 IC2. But on the ICR register, I can set all the bits except bit 17 to select timer 4 (I can set it 16). I configued PC13 as Alternate function AF14. Do you have an example working correctly

Re: I'm using theNucleo STM32L152 and I want to remap PC13 on timer 4 IC2. But on the ICR register, I can set all the bits except bit 17 to select timer 4 (I can set it 16). I configued PC13 as Alternate function AF14. Do you have an example working correctly

Re: I'm using the Nucleo-L152. I want to use the External clock on timer 2 and the counter does not increment. I use the same configuration on timer 3 and the counter increments as expected. Is there any issue with Timer2_ETR?