Timer as Counter

[muralij21]

Posted on December 03, 2010 at 11:49

Timer as Counter

[Andrew Neil]

Posted on May 17, 2011 at 14:17

''finding difficult and unable to get the output.''

Which part(s) are you finding difficult - doing the counting, or transmitting the count through the UART? Or both?

[lowpowermcu]

Posted on May 17, 2011 at 14:17 Hi David, Try to configure PA15 in input floating:   /* GPIOA clock enable */   RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);   GPIO_InitStructure.GPIO_Pin = GPIO_Pin_15;   GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;   GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;   GPIO_Init(GPIOA, &GPIO_InitStructure); Before that check that PA15 is shared with JTAG so you will lose connection with your debugger (Check it because I am not sure). MCU Lüfter

[Tesla DeLorean]

Posted on May 17, 2011 at 14:17

Might help if you provide a more complete example. Or use the library code, if you are programming the device at the register level, you should be prepared to debug it at that level.

[picguy2]

Posted on May 17, 2011 at 14:17

Recommendations from a software POV:

Allow the counter to run 0000-FFFF and back.  Don’t read out and reload as you may miss a pulse.  When it’s time to report:   temp = TMR2_CNT   saveForSerialPort = (temp-savedT2) & 0xFFFF //mask or save as half word   savedT2 = temp Time to report could be a timer ISR, a push button or a code event.  If its either of the first two it’s best to do the above in an ISR.  But don’t hang in that ISR until all your serial data is transmitted.  Instead, save the count (in a FIFO if necessary) for your non-ISR code to convert into characters for RS-232. Verify the above by running T2 as a timer with an appropriate prescaler.  This will divorce you from external events allowing for easier debug.

[muralij21]

Posted on May 17, 2011 at 14:17

I am having problem with the Counting part... USART part works fine..

Here is the code which i wrote.. TIM2->PSC=0x0000;     TIM2->ARR=0xffff;             //Autoreload value     TIM2->CNT=0x0000;     TIM2->EGR=0x0000; //0x0001;     TIM2->CR1=0X0280;             //0x0281;//Prescalar is 10 ie. tDTS=4*tCK_INT, autoreload enabled     TIM2->DIER = 0x0001;;                             // enable interrupt     NVIC->ISER[0]=0x4000000;     TIM2->SMCR=0x57;      //SMS=111 and TS=101 for TI1(PA15)     TIM2->CCMR1=0x100;  //CC2S=01     TIM2->CCER=0x00;     //CC2P=0     TIM2->CR1|=0x0001;        RCC->APB2ENR=0x00004004;     AFIO->MAPR=0x00000000;     GPIOA->CRH=(GPIOA->CRH & 0xFFFFF00F)|0x4B0;     USART1->BRR=0x341;     USART1->CR1=0x0000000C;     USART1->CR2=0x800;     USART1->CR1|=0x2000;     ch=0;     while(1)     {         if (TIM2->SR&0x40)         {             TIM2->SR&=0xffbf;             ch|=TIM2->CNT;             x=ch+0x30;             USART1->DR=x;                while (USART_IT_TXE==0);             a=USART1->SR;         }            }  } 

[muralij21]

Posted on May 17, 2011 at 14:17Hey i sort it out.. I hadn enable the clk.. Now its working fine

Thanks for help guys

[dsystem]

Posted on May 17, 2011 at 14:17

Hi Devid

I am trying to do the same, use Tim2 as Counter (ETR pin as Pulse input).

I failed.

Can you past your full code to help me?

Regards

Vimal

[mehmet.karakaya]

Posted on May 17, 2011 at 14:17

dont waste your time counting pulses at ETR pin

no matter what I tried I couldnot count ETR pulses - ( there is probably a bug in hardware ) try to count pulses at CH1 of the timer - it works in addition encoder mode 1 & 2 works like mode 3 ( another bug )

[dsystem]

Posted on May 17, 2011 at 14:17

Thanks Karakaya

You saved my days!!