Solved

Hi I am currently using STM32H723ZGT6 in my design. But because of the memory constraints for my application, I am planning to use STM32H743ZIT6 or STM32H753ZIT6 in my design. Please do let me know that these 3 MCUs are pin to pin compatible or a drop in replacement for each other or not? Regards,Sandeep

we have a ather  electrinc schooter ,they have used the 48 volt motor .motor image is attached .i am confusing that for this motor which board we can use for no load run ?

Where can I buy additional 34-pin STMod+ cables and DIL socket boards as the ones for STEVAL-STWINBX1 ?See attached picture for the additional parts I'm looking for - can also be used with the PROTEUS1 board but not supplied by default :frowning_face:Thanks, J.

I am using below codes. But this define not supportted #define KeepInCompilation __root #define KeepInCompilation __root   /* Private function prototypes -----------------------------------------------*/ int Init (); KeepInCompilation int Write (uint32_t Address, uint32_t Size, uint8_t* buffer); KeepInCompilation int SectorErase (uint32_t EraseStartAddress ,uint32_t EraseEndAddress); KeepInCompilation uint64_t Verify (uint32_t MemoryAddr, uint32_t RAMBufferAddr, uint32_t Size, uint32_t missalignement); KeepInCompilation HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority); KeepInCompilation int MassErase (uint32_t Parallelism );

Hi, Thank you for reading it.I made project using TouchGFX.I want to use a EXTI Falling Edge. (it will be use IRQ)I add the weak function. please see my codeapp_freertos.cvoid HAL_GPIO_EXTI_Falling_Callback(uint16_t GPIO_Pin) {UNUSED(GPIO_Pin);}when compile, I have following error.TouchGFX/Target/STM32TouchController.cpp:53: multiple definition of `HAL_GPIO_EXTI_Falling_Callback'  So, I open the target source file.STM32TouchController.cppextern "C" void HAL_GPIO_EXTI_Falling_Callback(uint16_t GPIO_Pin){if (GPIO_Pin == TS_INT_PIN){if (_initialized){if (BSP_TS_GetState(0, &state) != BSP_ERROR_NONE){assert(0 && "Failed to read TS state");}}}}  same name functions are in a one project.So I disabled the funtion in STM32TouchController.cpp.Then I can not touch anything in display. please let me know how to avoid the error and to work two function (touch and irq falling edge exti). thanks 

I am testing with a STM32MP157D-DK1 board with the goal of developing a custom board later. The board is useful to test everything I need except for the WIFI module. I have seen that in the page it seems that before a WLAN and bluethoot module was installed, but in the test board that I have it is not installed, and in the schematics of the board this module seems to have been removed, and the only thing that is seen is that it says DNF. What was the reason for removing the WIFI module? It did not get to work properly? On the other hand, if I replicate the circuit on a custom board can I make it work or would I have to integrate another module. In fact, is it in itself possible to incorporate the WIFI in the first place?I would appreciate to know the answers and decisions that were taken when removing the module.

Hello,currently I am using the NUCLEO-G474RE and the goal is to output a PWM signal simulating a sinewave. Therefore the duty cycle must continuously be adjusted.My issue is that I seemingly cannot do so.The Timer is configured as Timer D, TD1 output activeI selected the Basic configuration (though I also tried out the Advanced Configuration) and set the Period to 54400.The PWM on TD1 was used and the Compare value was set to 27000. All of that works fine and I get my PWM.However, when trying to change the Compare value using the HAL method or even by writing directly to the register, I don't see a change in my PWM signal.With the normal timers I just used:__HAL_TIM_SET_COMPARENow for the HRTIM I thought I'd use the equivalent:__HAL_HRTIM_SETCOMPAREBut the latter does not work for me. It does set the correct register and if I use the __HAL_HRTIM_GETCOMPARE, it correctly reads the new value. But that does not influence the duty cycle of my PWM.Am I missing something? Do I have to transf

When debugging custom hardware with the STM32L431KC, the debugger gets stuck in the reset handler:Reset_Handler: ldr sp, =_estack /* Set stack pointer */And in the console it says:Open On-Chip Debugger 0.12.0-rc1+dev-00061-g5e9b46d77 (2022-10-20-14:50) [https://github.com/STMicroelectronics/OpenOCD] Licensed under GNU GPL v2 For bug reports, read http://openocd.org/doc/doxygen/bugs.html Info : Listening on port 6666 for tcl connections Info : Listening on port 4444 for telnet connections Info : STLINK V3J10M3 (API v3) VID:PID 0483:374E Info : Target voltage: 3.274617 Info : clock speed 8000 kHz Info : stlink_dap_op_connect(connect) Info : SWD DPIDR 0x2ba01477 Info : [STM32L431KCUx.cpu] Cortex-M4 r0p1 processor detected Info : [STM32L431KCUx.cpu] target has 6 breakpoints, 4 watchpoints Info : starting gdb server for STM32L431KCUx.cpu on 3333 Info : Listening on port 3333 for gdb connections Info : [STM32L431KCUx.cpu] external reset detected Info : accepting 'gdb' connection on tcp/333

Hi,I'm working with a STM32G491KEU (512KB Flash).I use a custom bootloader so the startup in the printsreen is from the application. The MCU will first start in the custom bootloader and then it should change to the application.It reaches the startup_stm32g491keux.s and should branch to the mainApp with Address 0x800fcdc. The program counter is at 0x80131e2. And then it happens and it jumps wrong.Is that jump too long for "bl"? My answer: branch can work with MB ranges should not be an issue for the 512KB.Todays UpdateThere is something strange happening. If I have only an empty main (the same project) I get a very different disassembly. For me it looks like one is in thumb mode and the other one is ARM assembler.Any ideas?   

I am unable to configure TCPP03-M20 USB power controller chip available on B-U585I-IOT02A board.Supposedly, unlike most other boards, this board should be able to provide power to a device over USB-C connector.However, I found no examples of how to properly configure TCPP03-M20 chip. I am able to communicate with it over I2C, but when I try to activate "Gate Driver Provider" (power source) and "Normal" power mode according to DS13618 section "6.3.1 I2C registers" (p.11) by setting config register to 0x14, it just does not happen and "Gate Driver Consumer" (power sink) gets activated instead.Could anybody help? I am clueless. HAL_GPIO_WritePin(UCPD_PWR_GPIO_Port, UCPD_PWR_Pin, GPIO_PIN_SET); // enable TCPP03-M20 chip (U8) uint8_t data[2] = {0}; data[0] = 0x10; // Mode: normal power, Gate Driver: off, VCONN: both off status = HAL_I2C_Mem_Write(&hi2c2, 0x34 << 1, (uint16_t)0, I2C_MEMADD_SIZE_8BIT, data, 1, 100); status = HAL_I2C_Mem_Read(&hi2c2,

Hello,I have found informations about Unicleo-GUI, and I would like to test it. There are many informations on ST page, but I could not find any link to download it.So where can I download it?Thank you

I am working on register level programming, and I have gone thoroughly the reference manual it just contains about the features of the peripherals and registers and something about its working so how can I program if it does not contain the procedure for initializing and setting up the peripherals for usage if it is present tell me which document contains it so it will be very helpful. 

How a read memory command over RF works? I use the NFC Tap App and use the Read Memory command, where i can select Start Block ande Number of itmes. On the otherside i have a ST25DV64KC Tag.The question is, do the read use the mailbox or it is possible to read directly the memory? If the mailbox is used, how the transfer from the memory works. 

Hello, I cannot make the LIS2DU12 working in the Sensor.Tile module. I followed the instruction in the AN5648 but I get random values for X, Y, Z. At first, I'm trying to get the readings in normal continuous mode without FIFO. I can connect the device, WHO_AM_I returns the correct 69 value, I read X, y, & Z registers when the DRDY bit is set but these values are not correct.... In attach my configureLIS2DU12 and getLIS2DU12 functions and the X, Y, & Z values I get via serial Thanks, J.

I'm trying to setup a project with STM32CubeIDE 1.8 (includes CubeMX 6.4) that uses LPUART1 on a STM32L031K6. I want to lower the CPU frequency to 4MHz, and, to reduce power, I'm using HSI/4 as clock input.LPUART baudrate is set wrong (4 times higher than expected according to logic analyzer), it's generated out of PCLK1 frequency that is assigned as HSI_VALUE >> 2. While HSI_VALUE is defined in stm32l0xx_ll_rcc.h:#define HSI_VALUE (16000000U)But, during debug I realize that HSI_VALUE value is 4000000, it is redefined as a compiler directive:-mcpu=cortex-m0plus -std=gnu11 -g3 -DDEBUG -DSTM32L031xx -DUSE_FULL_LL_DRIVER -DHSE_VALUE=8000000 -DHSE_STARTUP_TIMEOUT=100 -DLSE_STARTUP_TIMEOUT=5000 -DLSE_VALUE=32768 -DMSI_VALUE=2097000 -DLSI_VALUE=37000 -DVDD_VALUE=3300 -DPREFETCH_ENABLE=0 -DINSTRUCTION_CACHE_ENABLE=1 -DDATA_CACHE_ENABLE=1 -DHSI_VALUE=4000000 -c -I../Core/Inc -I../Drivers/STM32L0xx_HAL_Driver/Inc -I../Drivers/CMSIS/Device/ST/STM32L0xx/Include -I../Drivers/CMSIS/Include -O

STM should really post their code to handle FPU context saving and restoring BECAUSE their clients have been asking for over a decade!!!One user stated "the time for a full FPU state save/restore is quite long. A pair of vpush {s0-31}/vpop {s0-s31} takes around 400ns on my STM32F407 @ 168MHz."Without this our code suffers floats sticking at nan0x400 status after IRQs.So, STM staff, come on, show us the best routine you have to save and restore the FPU status, because the Lazy FPU feature is useless!!

Hello everyoneCan I also add an svg image to a button? I can embed images in svg format (almost) without any problems. However, if I want to assign an image to a flex button, only png works. Is there a workaround for this or does it just not work?Regards, Roger

Hello,I have a project where I use both HAL and LL functions, on different files, for different funcitions.As described in UM2319, I defined both USE_HAL_DRIVER and USE_FULL_LL_DRIVER as compiler preprocessor symbols.In this case I have an error indicating that the stm32_assert.c file is absent.UM2319 says the stm32_assert.c file must be added only if I use LL drivers in stand-alone mode, but in my case I use both HAL and LL functions.I see that stm32_assert.c defines the assert_param() function, that is also defined in the stm32g0xx_hal_conf.h.In my case, can it create a redefinition conflict, when building?Moreover, if I try to omit USE_FULL_LL_DRIVER preprocessor symbol, the build is successful.My be this depend on the fact that, at the moment, I am using only few LL functions (the CRC ones)?Thank you,Carlo

Among STM32 boards, I would like to recommend a board that includes an interrupt 2 or more pins, I/O (Analog) 20 or more pins, MCLR (reset), PWM signal (more than 2 pins), AVdd, AVss, Vss, RX, TX, ICDCLK, and ICDDATA pins. This is the first board I'm entering, so I'm asking you a question while studying.

I have the problem on my STM32H753, that the IDLE-bit is set when transmitting. On the manual it says: The IDLE bit is not set again until the RXFNE bit has been set (i.e. a new idle line occurs).The RXFNE is never set (actually on CubeIDE this is shown as RXNE), because I do not receive anything. Also the RDR stays empty. And with logic analyzer I see that the RX-pin stays high the whole time. I also did not find anything on errata which could explain this. Any suggestions what it could be?

I'm using the UART (USART5) with RS485 and I have enabled the read to be on also when sending. I need to read back the data that was sent to see if it is correct. The problem is, that I do not receive what was sent. But if I send the same data from other device (without changing any code), I will receive the data. So the receive works, but not the same time with sending.Initialization - FIFO is also enabled. BaudRate = PARALLEL_BAUD_RATE; DataWidth = LL_USART_DATAWIDTH_8B; Parity = LL_USART_PARITY_NONE; StopBits = LL_USART_STOPBITS_1; HardwareFlowControl = LL_USART_HWCONTROL_NONE; OverSampling = LL_USART_OVERSAMPLING_16; PrescalerValue = LL_USART_PRESCALER_DIV1; TransferDirection = LL_USART_DIRECTION_TX_RX; And data sending is done with LL_USART_TransmitData8. The half-duplex is not enabled.What could block the receive when sending?

Hi everyone, I have a problem with placing data in RAM from DMA with H7. I have a custom bootloader that then jumps to the application that uses ADC, + DMA, TIM + DMA etc.. I ran the classic __attribute__((section(".D1buffer"),used)) and modified it on the .ld by adding its section, although with the latest ld files it is not needed.This happens: When I compile the project without including the bootloader everything works perfectly, but when I include the bootloader, after the jump the DMA stops working.Do I need to do any realignment or setup before jumping?On the bootloader side I run this before jumping and clear every interrupt and blank everything:voidapplicationJump(void){ typedef void(*pFunction)(void); volatile uint32_t BootAddr=BOOT_APP_ADDR; uint32_t JumpAddress=*(__IO uint32_t*)(BootAddr+4); pFunction JumpToApplication=(pFunction)JumpAddress; HAL_MPU_Disable(); HAL_SuspendTick(); __HAL_RCC_AHB1_FORCE_RESET(); __HAL_RCC_AHB1_RELEASE_RESET(); __HAL_RCC_AHB2_FORCE_RESET(); __HA

Hi Community,I'm porting STM32G071 SBSFU to STM32G0B1RE and Customizing UART to USB CDC.I'm using Nucleo-G0B1RE dev kit and STMCubeIde for development.1. I'm able to build, load, run both STM32G071 SBSFU and UserApp without any changes. but when I change project global symbol STM32G071xx to STM32B1xx in properties->Settings->Preprocessor->Define Symbols. The have made appropriate changes after loading USERApp causes hard fault and resetting device.2. Also tried changing sbsfu and fwimg .ld files for rom and ram address with/without changing define symbols above mentioned also had similar issue.Now I am stuck without knowing what needs to change and how to port the code to STM32G0B1 ?Can you please help with require changes to port from STM32G071 to STM32G0B1 ? TIA,Tarun 

Hello,I have a problem with a clock configuration on my STM32F072C8T6. I need the 48MHz clock (HSI48) for the onboard USB communication. I have enabled this via ioc in the clock configuration. Everything looks fine there and no conflict is reported.Now as soon as I load my program on the STM32, the debug connection breaks as soon as the following line is executed (in the automatically generated SystemClock_Config function --> see attachment) :__HAL_RCC_HSI48_ENABLE(); (in the stm32f0xx_hal_rcc.c file)I see that this line only writes the CR2 register with the following command:RCC->CR2 |= RCC_CR2_HSI48ON;Unfortunately I can't see which error handler the STM32 goes into, because the debug connection breaks. I have also tried to increase the FLASH latency with the following line, unfortunately without success:FLASH->ACR |= 0x1;If I run the program with the 8MHz everything works without problems.Am I missing something? Can someone help me? Thanks a lot!

Is there a way to read an environment variable from the PC (I'm running on a Windows box) and pass that value somehow (maybe via a temporarily created define for the command line) such that a file being compiled can use the value of that environment variable? For example, can the name of the person who's doing the build be used to initialize a string value that can then be embedded into the app?Thanks!