Solved

Hey st i am working with the stm32f407g and i am trying to make the LSM303 working on my board. At this moment i am using this lib: https://github.com/STMicroelectronics/STM32CubeL4/blob/master/Drivers/BSP/Components/lsm303dlhc/lsm303dlhc.cThe problem i am having is that it cant find the COMPASSACCELERO_IO_WRITE function and the COMPASSACCELERO_IO_Init function. I think this is because i am missing a .A or .LIB. Could i get help with this?

Because I don't want use HAL , but want use the possibility to configure pins with CubeMX

Where can I find documentation on the BLE attribute handle offsets? I was adapting code from the sensor demo for the BLE NRG 2 and am trying to understand the "aci_gatt_attribute_modified_event" callback. Through observation and experimentation I found that adding 1 to the attribute handle identifies write characteristic events from the BLE client and adding 2 to the handle identifies characteristic notifications being enabled or disabled. I haven't seen any description of this behavior in the BLE programming guide, but I would like to know all the available offsets and what they are for.

hi i have a problem where i want to get the stm to 480Mhz clock but in order to do that i have to set the Power regulator voltage scale to 0 but when i do this the micro controller bugs and i cant connect to it the programmer just say no stm32 found how can i increase the frequency ? i have my custom board i'll share anything if needed

I want to use the EH pin of ST25DV to obtain energy through RF and power supply data transmission for low-power MCU (stm32L4). Can this scheme be realized? What should I do?

HiI'm trying to connect I-NUCLEO-LRWAN1 with Nucleo-L073RZ to gateway bt it's not getting connected.

[VERSION]: 6.2.0[TOOL]: ST Motor Pilot/ MotorControl Workbench 6.2.0[DETAILS]:1.The speed ki ‘s numerical values ​​do not correspond.It is different from 5.Y.4.2. About the Board Maneger. I want to add my own board but no documentation guidance.3. About the Phases Current Sensing. I want to change it to Isolated Current Sensors, but the same reason.I'm expecting a reply. 

Hi,I have STEVAL-MKI109v3 board and steval-mki186v1 sensor. I have connected the sensor to the board and if I connect the board to my laptop, the laptop is not able to detect the COM port of the board which is connected. It is not detecting the board in Unico-GUI also. If I connect the board the power led (D6) is ON and also the D1 LED (green LED) is blinking. But it is not detecting in my laptop. My laptop currently runs on Windows 10. I also tried installing the driver on a windows 7 laptop and tried connecting the board but still the same. Please help !

Hello.I am very new to ST electronics, though I've spent several years working with chips from another popular manufacturer.I would like to develop a board that prioritizes multiple high-speed gpio lines.I do NOT need:-sdcard, usb, external flash, etc.I do need:-maximum number of contiguous gpio lines.-maximum clock speed (550MHz ?)-in-circuit programming/debuggingAm I correct in thinking the STM32H730VBT6 can be run with internal flash and data memory only?To achieve 550Mhz would require external oscillator setup and pll?If so, can anyone point me to the minimum board setup to achieve this?Thank you very much!Rob.

Hi there,I am having issues spinning a BLDC motor using the EVSPIN32F02Q1S1 development kit, and after searching through the data brief and cross referencing the schematics with the values populated in MC Workbench, I found a discrepancy in the current sense gain.In the image taken below of the Current Sensing tab from MC Workbench, the current sense gain is hardcoded to 3.33, and it cannot be changed. I am using MC Workbench version 6.1.2, and have imported the EVSPIN32F02Q1S1 board settings from MC Workbench.In this next image, taken from page 4 of the EVSPIN32F02Q1S1 databrief, if I am understanding correctly, the gain is simply the non-inverting op amp gain of 10k/3k+1 = 4.33, so it seems like MC workbench forgot to account for the +1.I tried manually going into the .ioc file and changing the gain to 4.33 but that didn't solve my issue, so I am still testing out other things to get the motor spinning, which I will likely make a separate post for if I am unsucces

We are communicating with the st25r3916 chip normally.But after about 14 minutes,The value of the IRQ pin is maintained at HIGH.You fall into an infinite loop in the function st25r3916CheckForReceivedInterruptts().What is the problem ?please I'd appreciate it if you let me know.Infinite loop.while( platformGpioIsHigh( ST25R391X_INT_PORT, ST25R391X_INT_PIN ) )  {    st25r3916ReadMultipleRegisters( ST25R3916_REG_IRQ_MAIN, iregs, ST25R3916_INT_REGS_LEN );        irqStatus |= (uint32_t)iregs[0];    irqStatus |= (uint32_t)iregs[1]<<8;    irqStatus |= (uint32_t)iregs[2]<<16;    irqStatus |= (uint32_t)iregs[3]<<24;  }

I saw somewhere in the forum that the TOF sensors see [optical] pings from other sensors as ambient light (meaning they are able to ignore them) but are still able to detect their own bounce. Is that true? If yes, can someone explain how that works?Note, I'm referring to the situation where you have independent devices in an area moving around, each of which have their own TOF sensor(s) for obstacle avoidance. The point here is that there is no synchronization between each device, so there would surely be overlapping [optical] pings.(I accidentally posted this to the wrong forum group, so this is a re-post of the same question) 

Hi,I am working with STM32G491RE.I am giving pulse to GPIO pin from function generator. That pulse will be 2 msec on time and 8msec off time.I need to make flag high if the signal from function generator lost.Can anyone suggest me how to do this?void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin){if(GPIO_Pin==detect_Pin){if(HAL_GPIO_ReadPin(detect_GPIO_Port,detect_Pin)==GPIO_PIN_SET){ HAL_UART_Transmit(&huart2, (uint8_t *)"rising:",7, HAL_MAX_DELAY); }else if(HAL_GPIO_ReadPin(detect_GPIO_Port,detect_Pin)==GPIO_PIN_RESET){ HAL_UART_Transmit(&huart2, (uint8_t *)"falling:",8, HAL_MAX_DELAY); }else{ HAL_GPIO_WritePin(led_GPIO_Port,led_Pin,GPIO_PIN_SET);} I tried with EXTI interrupt but If input is there from generator its detecting both rising and falling edge and if there is no signal from generator I am not getting  in to else condition.img: pulse input from function generator.1.If I want to make flag high for no signal from function generator,above image offtime also it con

Hello!I'm trying to setup up timer6, i need to use it at different frequencies at different times. To test the timer i toggle an output pin in the ISR and measure the frequency with an oscilloscope, but the frequency is consistently off by about 10%.Any suggestions to why this is? My solution would be to multiply the wanted frequency by some calibration factor.I would like a frequency of 2 Hz, so the timer interrupts should be at 4 Hz to toggle on and off.The timer setup is:32 MHz PLLCLKPrescaler = 125Period = 64000

Hello,is it possible to add a command in the startup tab of the debug configuration, to erase a group of selected sectors, before programming?For example I want to erase sectors [16..63], but not sectors [0..15].I have only found the "monitor flash mass_erase" command, but it erase all flash.Thank you,Carlo

Hello,I want to change the MCU STM32F779AIY to STM32F779NIH6I already checked the pinout in CubeMX and i can use the same config for the peripherals at the same naming of pins (PB1, PA4 and so on).Do i need to change anything at the software if i change the MCU?As i can see so far, the software does not detect the type of the MCU, as long as GPIO stuff is the same (which is) it will work. Am i right here? Thank you.

I'm trying to testing secure boot on a STM32MP157F-EV1. To do so, I planned to use the fuse override command to test secure boot without having to actually burn the OTP 24-31 with the public key hash.But it appears that fuse override command is not working properly: after overriding cache to store publicKeyhash.bin, the read is exempt of the key. (note: the publicKeyHash_values is a placeholder)STM32MP> fuse override 0 0x00000018 publicKeyhash_values Overriding bank 0 word 0x00000018 with publicKeyhash_values[0] Overriding bank 0 word 0x00000019 with publicKeyhash_values[1] Overriding bank 0 word 0x0000001a with publicKeyhash_values[2] Overriding bank 0 word 0x0000001b with publicKeyhash_values[3] Overriding bank 0 word 0x0000001c with publicKeyhash_values[4] Overriding bank 0 word 0x0000001d with publicKeyhash_values[5] Overriding bank 0 word 0x0000001e with publicKeyhash_values[6] Overriding bank 0 word 0x0000001f with publicKeyhash_values[7] STM32MP> fuse read 0 0x00000018 8

What is the minimum and maximum voltage the internal ADC of stm32f429 can measure ?

Custom board. Boot log as belowextlinux.conf:MENU BACKGROUND /splash_landscape.bmpTIMEOUT 20LABEL OpenSTLinuxKERNEL /uImageFDTDIR /INITRD /st-image-resize-initrdAPPEND root=PARTUUID=e91c4e10-16e6-4c0e-bd0e-77becf4a3582 rootwait rw console=${console},${baudrate} dyndbg="file drivers/usb/core/hub.c +p"adding the dyndbg following: https://wiki.st.com/stm32mpu/wiki/How_to_use_the_kernel_dynamic_debug#Debug_messages_during_boot_processums 0 mmc 0Did not show /media/$USER/bootfs.Any hints/ideas/suggestion to (enable) debug the root cause?the dt of u-boot is the same as for the kernel.The kernel uImage and DT blob were copied to bootfs.The rootfs /lib/modules was also updated, probably not needed as the  SD card was created with the files and tools of the starter package in ECO 5.0.0. and modules were not changed.U-Boot 2022.10-stm32mp-r1 (Oct 06 2023 - 20:22:10 +0800)CPU: STM32MP157AAA Rev.BModel: STMicroelectronics custom STM32CubeMX board - openstlinux-6.1-yocto-mickledore-mp1-v23.06.

Run bitbake rep and sync and DISTRO, then bitbake , it shows the EULA and the build start, interrupt the build by press CTRL-C, closing the console window and re-entering it. then start bitbake, below errors occur.Even creating a new folder running the repo and sync command and then DISTRO shows:HOST DISTRIB check]Linux Distrib: UbuntuLinux Release: 23.04[source layers/openembedded-core/oe-init-build-env][from nothing][EULA configuration][WARNING] No eula file found : not able to configure EULA agreement or not.[Configure *.conf files][INFO] No 'site.conf.sample' file available at /home/user/distro/layers/meta-st/scripts. Create default one...[WARNING] Not able to find STM32MP1.conf file in layers/meta-st : bblayer.conf not updated...===========================================================================Configuration files have been created for the following configuration:DISTRO : openstlinux-westonDISTRO_CODENAME : mickledoreMACHINE : STM32MP1BB_NUMBER_THREADS : <no-custom-conf

Hello.I am testing using MCSDK 6.2.0 on EVSPIN32G4 board.I've checked the operation of the motor using the start/stop button.The problem takes approximately 3 seconds or more to stop during operation at a maximum speed of 16000 rpm.I want to stop urgently, what are the ways?Regards

I have generated the code with workbench 6.1.2 planning to migrate to 6.2.0 but meanwhile i am finding one issue consistently. I am using digital hall sensors and i am constantly getting a gap as below in the rotor angle after every some duration. Is it normal this is the cube monitor logging?I have captured the phase current and i find a small glitch which happens consistently.If it is related to the rotor position. Please help to solve this issue.  

Hi,I'm to SPI in stm32,I want to interface LCD with SPI RGB i need your support to provide SPI intialzaton code for LCD WF40ESWAA6DNN0 480*480 resolution.Thanks

JW 

..