Solved

I change the HIDdescMap to uint8_t reportDesc[] = {    0x05, 0x01,                 // Usage Page (Generic Desktop)        0x09, 0x06,                 // Usage (Keyboard)        0xA1, 0x01,                 // Collection (Application)        0x05, 0x07,                 //     Usage Page (Key Codes)        0x19, 0xe0,                 //     Usage Minimum (224)        0x29, 0xe7,                 //     Usage Maximum (231)        0x15, 0x00,                 //    &n

STM32H573AII3Q is a 169 pin UFBGA SMPS package. Along with SMPS option, does it also have internal LDO for core supply? Can we use internal LDO to supply core voltage for this package?

Hello,I'm currently working with the STM32h573I-DK Board and I'm interested in installing SFI (Secure Firmware Installation) and learning how to work with it. Could you please provide guidance on how to install SFI and any resources such as tutorial videos that could help me get started?Thank you!

Hi,mcsdk: 6.2.1control board: nucleo-g474reBridge: XNUCLEO-IHM09M2Power Board: STEVAL-CTM009V1Motor: Motenergy ME1304 I prepared motor profile for ME1306 with help of EVSPIN32G4 and used in configuration,described above.But now I get Startup failure on every start. The shaft does not rotate but trembles only.Can I get any advice how to debug the issue?Appreciate in advance.

Hello,When I right click on a pin, in the Pinout view of an IOC file, it shows the following:I understand the ADC1_INP3, since that is the intended setting.  But what would the yellow ADC2_INP3, with a + next to it, signify?  Likewise, what is the reason for the green highlighted GPIO_Analog? Here is another example:What is the purpose of the 4 "+" signs?, some with color shading and some without.  I assume selection of both ADC2_INP19 and DAC1_OUT2, means PA5 is routed to both?Regards,Robert

After about an month, I connected my NUCLEO-L4A6ZG to my PC again. STM32CubeIDE nor the STM32CubeProgrammer can't recognize my board. I already tried different USB ports and different USB cables.When Trying to run a program the Error Message in the IDE is "No ST-Link detected! Please connect ST-Link and restart the debug session." and in the Programmer "Error: No debug probe detected". My board is powered on but seemingly not recognized. The red LED is constantly blinking (red-off-red-off-...). The green LED is constantly green.In case it required, my OS is Linux Mint (switched it from Fedora within the month i haven't used the board).I am an absolute noob, with almost no knowledge when it comes to the topic. I don't know what I can do to fix it and ask for help.

I want to understand the Timeout parameter of the HAL_SPI_Transmit, HAL_SPI_Receive and HAL_SPI_TransmitReceive function.

..

[VERSION]: 6.2.1[TOOL]: MC WB[DETAILS]:We are making a custom PCBA based on a STm32G474METx. Algorithm is FOC.I'm trying to activate Over current protection, but:My hwVariant is (parameters are not tuned/configured yet)"type": "SingleInput_RawCurrents_Protection_IntRef", "help": "Default Configuration", "signals": { "CURRENT_INPUT_P": [ { "name": "PB13", "help": "", "cost": 0 } ] }, "OCNetworkGain": 1, "OCNetworkOffset": 1, "OCComparatorThreshold": 1, "OCSignalPolarity": "Active high"Current sensing is defined as: "type": "TwoICSCurrents", "help": "How to enable this variant", "signals": { "CURRENT_ICS_U": [ { "name": "PA0", "help": "", "cost": 0 } ], "CURRENT_ICS_V": [ { "name": "PA1", "help": "", "cost": 0 } ] }, "icsGain": 0.004All features other than over current protection are shown as expected.For reference; full current sensing tab:How should I configure my .json to be able to activate over current protection?[EXPECTED BEHAVIOR]:Being able to act

Hallo, how to determine the file presents in a folder with filex?What function is available?

I cant make work the HRTIM. I am using the weact board.I tried HRTIM-A and TRTIM-D using the cubeide (latest updated). the first one using "basic HAL" and the second using "Advanced Hal" instructionsTIM5 works so it seems that clock is working.I added following code to make run the timers and the debugger passed them without trouble: MX_HRTIM_Init(); if( HAL_HRTIM_WaveformOutputStart(&hhrtim, HRTIM_OUTPUT_TD1)!= HAL_OK) { Error_Handler(); } if (HAL_HRTIM_WaveformOutputStart(&hhrtim, HRTIM_OUTPUT_TD2)!= HAL_OK) { Error_Handler(); } if (HAL_HRTIM_WaveformCountStart_IT(&hhrtim, HRTIM_TIMERID_TIMER_D)!= HAL_OK) { Error_Handler(); } if (HAL_HRTIM_WaveformCounterStart(&hhrtim, HRTIM_TIMERID_TIMER_D)!= HAL_OK) { Error_Handler(); } if ( HAL_HRTIM_WaveformSetOutputLevel(&hhrtim, HRTIM_TIMERINDEX_TIMER_D, HRTIM_OUTPUT_TD1, HRTIM_OUTPUTLEVEL_ACTIVE)!=HAL_OK) { Error_Handler(); } if ( HAL_HRTIM_WaveformSetOutputLevel(&hhrtim, HRTIM_TIMERINDEX_T

Hi everyone!I use RTC with STM32CubeIDE for my STM32. Just a question: is it possible to set the alarm day over several days so that the alarm wakes up every Monday AND Friday?Thank you !  

I have an STM32G071CBTx with a rotary encoder wired to GPIO pins PB5 + PB7 (LPTIM1_IN1 and LPTIM1_IN2), but for some reason it will never count down no matter which way the encoder is turned.I have checked the encoder waveforms and they are as expected, and it's not just "rattling" with one input stuck low or high as I can make the counter run through the full count range by turning the encoder.Initialisation code (LL) looks like this:void MX_LPTIM1_Init(void) { /* USER CODE BEGIN LPTIM1_Init 0 */ /* USER CODE END LPTIM1_Init 0 */ LL_GPIO_InitTypeDef GPIO_InitStruct = {0}; LL_RCC_SetLPTIMClockSource(LL_RCC_LPTIM1_CLKSOURCE_PCLK1); /* Peripheral clock enable */ LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_LPTIM1); LL_IOP_GRP1_EnableClock(LL_IOP_GRP1_PERIPH_GPIOB); /**LPTIM1 GPIO Configuration PB5 ------> LPTIM1_IN1 PB7 ------> LPTIM1_IN2 */ GPIO_InitStruct.Pin = ENC1_As_Pin; GPIO_InitStruct.Mode = LL_GPIO_MODE_ALTERNATE; GPIO_InitStruct.Speed = LL_GPIO_SPEED_F

Hello, i installed STM32 CubeMX 6.2.9 today. I tried to add software packages by clicking "help" -> "Manage embedded software packages", but nothing happens. Then i tried to log in using "myST" -> "Login", but again nothing happens and i can not log in. I tried using ALT U and ALT L but it did not work.I attached the log file of STM32CubeMXThanks,Marisa

Hello to all, Our design is using STM32F042G6 MCU to implement STSW-STM32011 firmware interface based on STM32Cube which implements ISO7816 protocol for us to talk to smart card. Unfortunately it does not seem to move beyond ATR.Is our MCU we use not good enough to support this FW, can it support only T=0 without T=1? If not good enough, what is the minimal MCU that would support the above FW or similar for ISO7816 over USART?Thanks for your help, Peter

0Hi I am trying to write a c/c++ application which will excercise the Tx and Rx pins of the can interfaces (can0 and can1) available in the STM32MP157CAA.Approach One I wrote an application which opens a socket on can0 and then writes into the Tx of can0 receive the same bytes on the Rx of can0. And same for the can1. I followed the loopback mechanism described in the below ST wiki: https://wiki.st.com/stm32mpu/wiki/How_to_send_or_receive_CAN_data#Hardware_self-testThis works. But it turns out that the above loopback happens internally and doesn't actually send the packet through the Tx pin.Approach Two Now, I am thinking if I can physically connect the Tx of can0 with the Rx of can1 using a female to female connector, and then open two separate sockets for can0 and can1, write on the Tx of can0 and then try receiving on the Rx of can1 - should that work? I have given it a quick try but doesn't seem to be working.I am not sure technically if this approach is even valid.

We start developing our project using NUCLEO-L476RG with NUCLEO-NFC08A1 using NFC08A1_PollingTagDetectNDEF application.We develop a board with ST25R3916B and a microcontroller with FreeRTOS.We import the RFAL library and BSP component st25r3916_xxx.c, we don't import NDEF layer. We make on our board a task with void demoCycle( void ) cloned from demo_polling.c,plus all the function take from the example application.We made all the rfal_platform MACRO conversion.The board work well with different card and TAG and also in P2P connection with NUCLEO-L476RG with NUCLEO-NFC08A1.If we try to connect in P2P mode 2 of our board the connection doesn't start.With NUCLEO-L476RG either the board entered in demoCycle case switch:case RFAL_NFC_LISTEN_TYPE_AP2P:case RFAL_NFC_POLL_TYPE_AP2P:platformLog("NFC Active P2P device found. NFCID3: %s\r\n", hex2Str(nfcDevice->nfcid, nfcDevice->nfcidLen));platformLedOn(PLATFORM_LED_AP2P_PORT, PLATFORM_LED_AP2P_PIN);demoP2P( nfcDev

Is there a possibility to use protobuf format. If possible can you please explain the process how to pack the protobuf format in the board.Iam using STM32H573I-DK Board

Hello Community, I am using the STM32U585 in a design, and I have VDD at 3.3V and VDDIO2 at 1.8V.  The 1.8V rail is supplied by a 3.3V to 1.8V voltage regulator. I connected the Enable of this voltage regulator to one of the STM32U585 I/O (this I/O isn't on the PG port, because PG port is supplied by VDDIO2). Do you foresee any problem with this setup? I mean the 3.3V will turn on at first, and then the STM32 will turn on the 1.8V regulator, which supply VDDIO2 rail.  In the datasheet it is clear that, VDDIO2 and VDD are two independent supplies. I just want a confirmation, and if someone here has a similar implementation in a working design. Thank you, Lamia

Hello,will you build a keyboard without Pngs to save space , in the future?

Hi there, During OP-TEE integration of our custom platform based on STM32MP151C MPU I'm facing an issue with DFU. It looks like the dfu command stucks in `run_usb_dnl_gadget` inside the loop and waits forever for the flush flag: NOTICE: CPU: STM32MP151CAC Rev.ZNOTICE: Model: STMicroelectronics custom STM32CubeMX board (TF-A)INFO: Reset reason (0x15):INFO: Power-on Reset (rst_por)INFO: FCONF: Reading TB_FW firmware configuration file from: 0x2ffe2000INFO: FCONF: Reading firmware configuration information for: stm32mp_ioINFO: Using USBINFO: Instance 2INFO: Boot used partition fsbl1NOTICE: BL2: v2.6-stm32mp1-r1.0(debug):v2.6-dirtyNOTICE: BL2: Built : 13:14:26, Nov 23 2021INFO: BL2: Doing platform setupINFO: RAM: DDR3-DDR3L 16bits 533000KhzINFO: Memory size = 0x8000000 (128 MB)INFO: DFU USB START...INFO: phase ID :3, Manifestation 3 at c7159862INFO: Send detach requestINFO: Receive DFU DetachINFO: DFU USB STOP...INFO: BL2: Loading image id 31INFO: Loading image id=31 at address 0

Hello, I am on the RX FOD Tunning (BPP) phase, and I have a question.   In the document, it is written - Reading Ptx and Prx is done automatically when using STEVAL- WBC86TX . But I am using just custom board, so I recorded the power from the  "Charts" Tab and save it to .csv file. While looking .csv file, there's TX TX PWR(mW), TX RX PWR(mW)  at the very right side. Do they mean TX or RX power seen from TX's side? And sometimes the RX power is slightly bigger than TX power. Could you tell me why is that ? And can I replace it with the .csv file data instead of automatically recorded value? Thank You. -Jake-

Hi,i have modified 2 eval NFC08A1 and now i'm using ST25R3916B not in balance mode but with 2 single ended RF circuitry.If i use the  RFIO1 i can establish a P2P connection between the 2 evals, insted if i change and use the RFOI2, the P2P connection doesn't work, i can only read passive tags.The register 00h permits to choose balance or differential output and which output use, but all the other registers refer to RFOI1, or RFOI2?where is written what can i can do or don't with the periferal RFIO1 or RFIO2? Are they different???

 Hi, I learned how to make the clock by following the 3 tutorials ( https://support.touchgfx.com/docs/tutorials/tutorial-03 ). I changed a data in the program because it counted minutes and seconds. Now I noticed that after 18 minutes the circle freezes and no longer runs, if you intervene manually by switching from one screen to another it clearly updates and starts again for another 18 minutes. can someone help me? Thank you 

Posted on June 06, 2018 at 16:57I'm doing a pcb design using the STBC03 for managing the battery (power path and battery charger). It has a 0.4mm pitch BGA30 footprint. Has anybody done a design like this? Is there any guideline for it? Thanks.#bga-routing #pcb-design #stbc03