Solved

The example code for X-NUCLEO-NFC03A1 does not have a few methods mentioned in the headers, including st25r95SetACState(). This makes the 14443A emulation code not useful. Can you please provide the working example? Thank you

 I'm trying to flash my custom STM32L152RET6 board using the command-line version of CubeProgrammer. Initially, everything seemed fine, but I wanted to ensure the firmware couldn't be read out. So, I set the option bytes with -ob RDP=1 to enable read protection. However, after doing this, the flashing process failed, and now my program no longer runs.I was able to flash it again using a Segger debugger, but when I try to run the program, it crashes at startup. The voltages all seem normal, so I don't suspect a hardware issue. Could this be due to some incorrectly set registers or option bytes in the CPU?Here’s the command I used:STM32_Programmer_CLI.exe -c port=usb1 -ob RDP=1 -d firmware.hex -v Any advice would be greatly appreciated!  

Hi all,I was reading through the documentation of the STM32H723 to find out what clock speed I can configure the FMC to run at using an external SDRAM. Looking at older posts and videos there is mentioned 100 MHz, but when I look at the newer/revised (revision 3) the max kernel fmc frequency has increased from 200 to 275 MHz:Does this mean that now an external SDRAM can run at 137.5 MHz (kernel clock / 2) and not 100 MHz?Best regards Links I have compared to:https://community.st.com/t5/stm32-mcus-products/stm32h7-maximum-sdram-frequency/td-p/336641#:~:text=Maximum%20SDRAM%20frequency%20is%20100%20MHz.&text=%2C%20section%208.5.,not%20be%20above%20200%20MHz. https://www.youtube.com/watch?v=h28D4AaPSjg (14:00 min) https://community.st.com/t5/stm32-mcus/how-to-set-up-the-fmc-peripheral-to-interface-with-the-sdram/ta-p/49457 

Regarding the shunt resistors connected to the SENSEA and SENSEB pins, the UM1829 has three 0.1 ohm resistors connected. Why is this? The datasheet says one 0.1 ohm resistor.Do I really need three of them?

Using the latest CubeMX 6.9.0 on Ubuntu  23.04  The following has happened quite a few times in the past years , also on  previous Linux and CubeMX versions. Now would like to raise this  issue as it's becoming very annoying now doing more work in CubeMX. There are now more situations where the keyboard just does not respond anymore. The mouse does.1. When creating a new project and entering an partnumber, the dialog box  sometimes get stuck. Mostly after entering a partnumber that does not exists.  You can continue by  selecting from the drop down list and then creating the project,  but when trying to save you are out of luck, you cannot enter a filename so you have to start all over again. a lot of wasted time.2. When entering a pin number in the dialog box. sometimes this text box get stuck. Luckily you can save the project, but need to close CubeMX and restart it gain. A lot of time wasted. This happens no matter it is an MCU or MPU pro

I am using the STSW-IMG501 software with the STEVAL-EVK-U0I1 evaluation kit and the STEVAL-56G3MAI1 evaluation board for the VD56G3 image sensor.  I am trying to capture videos of my target application at high frame rates to assess the sensor properties, but I am unable to get the STSW-IMG501 to capture at frame rates equivalent to what is programmed in the VD56G3 image sensor.A short description of applicable frame rate parameters:Line Length - 1236 (0x0300, 0xd4, 0x04)Pixel Clock - 160.8 MHzLine Time - 7.69 us (Line Length / Pixel Clock)Subsampling/Binning Factor - 1 (no subsampling or binning)Ystart - 442 (0x045a, 0xba, 0x01)Yend - 921 (0x045c, 0x99, 0x03)Frame Length Offset - 69Minimum Frame Length - 549 ((Yend - Ystart+1)/(subsampling factor) + frame length offset)Target Frame Rate - 200 HzProgrammed Frame Length - 650 (0x0458, 0x8a, 0x02)Target Frame Duration - 5 msTarget Exposure Duration - 3.5 msCoarse Exposure - 455 (0x044e, 0xc7, 0x01)In order to verify my configuration

HiI use the HAL library and CMSIS-RTOS2infinite loops should not be used in the thread, but I need to wait, for example, for the packet to be sent via I2C, because I need to write and read right after each other, and if I don't wait for the HAL_I2C_STATE_READY state, only writing is performed, but reading does not take placeis the solution to use osThreadYield() ?static void Task1(void *argument) { while(1) { HAL_I2C_Master_Transmit_IT(&hi2c1, I2C_addr, write_data_array,sizeof(write_data_array)); while(hi2c1.State != HAL_I2C_STATE_READY) { osThreadYield() ; } HAL_I2C_Master_Receive_IT(&hi2c1, I2C_addr, read_data_array,sizeof(read_data_array)); while(hi2c1.State != HAL_I2C_STATE_READY) { osThreadYield() ; } } }or set a semaphore(event) in the I2C interrupt handler and watch it in the thread?osSemaphoreId_t I2C_semaphore; void I2C1_EV_IRQHandler(void) { HAL_I2C_EV_IRQHandler(&hi2c1); if(hi2c1.State == HAL_I2C_STATE_READY) osSemaphoreRelease(I2C

Hi, Can PD Controller (STUSB4710) act as a DRD?STUSB4710 - Stand-alone USB PD controller (with short-to-VBUS protection) - STMicroelectronicsI believe that STUSB4710 cannnot operate as DRD (Dual Role Data), and can only function as UFP.If there is a way to operate it as DRD, please let me know how to configure it. 

The STM32WB1MMCH6TR module has a BOOT0 pin that is pulled high on the MB1868 "B-WB1M-WPAN1" board through (what appears to be) a non-populated resistor. Without this resistor the BOOT0 input to the module is floating.  Does the module pull the signal down internally or is the BOOT0 input to the STM32WB15CC on the module left floating? Is there a design guide document for using the STM32WB1MM?  So far I've been using the bare chip documentation and the B-WB1M-WPAN1 board as a guide.  I do have the STM32WB1MMC datasheet (DS14096 - Rev 7 - August 2024) but there aren't a lot of details.

I have a small micro that needs to run before the MP157 is active. The voltage coming gin is 5V, but I need 3.3V. Is there an always-on LDO in the STPMIC1 for such purpose? I assume the internal LDO is not te be used?Do I need to program the voltage of the LDO or is it set by default to 3.3VRegards

Hey Guys,I have problems about configure my STM32H743VIT SysClock.On my own PCB, i have a Crystal with 8 MHZ, and a LSE of 32.768 khz.Settings are in my Screenshots, now if i debug my application, it ends in a Error Handler.. but why?BTW: UART4,5,7 and USART1,2 enabled, and USB_DEVICE + USB_HOST is enabled.   if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { Error_Handler(); /** JUMPS TO ERROR_HANDLER **/ }  my complete SystemClockConfig:  void SystemClock_Config(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; /** Supply configuration update enable */ HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY); /** Configure the main internal regulator output voltage */ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2); while(!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) {} /** Initializes the RCC Oscillators according to the specified parameters * in the RCC_OscInitTypeDef structure. */ RCC_OscIn

I'm trying out the board designer feature and ran into an issue where after succesfully making a board in Board Designer based on a custom STM32G431 motor controller board, MCWB gives this error about the current sensing not being found:The Board Designer doesn't show any errors: I have a current sensing feature added with 3 shunt resistor readings from a DRV8323 chip: Can anyone give me some advice on what to try next to get this to work?  This is such a cool tool I'd love to get working. 

HelloWe are working on a product using the STM32WLE5JC MCU. The features a magnetic switch that generates interrupts (specifically a low to high transition) which is meant to wake up the MCU from STOP2 mode. What is the ideal way to do this? We have few free GPIO pins. Could we use any GPIO with an external interrupt or does the switch need to be connected to dedicated wakeup pin? 

Hi,I am currently playing with the NUCLEO-WBA55 board with the BLE_p2pServer_ota example.During the advertising process, I got this raw data with the BLE scanner on my phone. I mean that the 0x30 is the ID for STMicroelectronics, but what is behind it? Can someone explain to me what 000010080E12AAB is?

 Hello, I was hoping for some help on which way to use a keyboard on TouchGFX. It will be the same keyboard from the example provided by TouchGFX. My application has multiple screens (10-12) where it uses a keyboard. Would it be more efficient memory/gpu wise tooverlay a keyboard on every screen and use setVisible true/false for when user wants keyboard openedcreate one screen for the keyboard and whenever the user wants to use the keyboard it goes to that screenI was a bit confused because I know it takes resources for the screen to draw the keyboard images and the mappings, so I thought using one screen would be more efficient. But, TouchGFX loses the state and destroys the screen that it leaves, meaning using one screen would be constant redraws, not to mention carrying over state and managing buffers so the keyboard can send data back to the screen where user came fromIs there a "norm" when it comes to using keyboard on TouchGFX?

I like to configure IWDG (with early interrupt), but the UI in STM32CubeMX for IWDG lacks the NVIC settings tab compared to WWDG. I know that both units share the same ISR "WWDG_IWDG_IRQHandler", but why do I need to activate WWDG to get the Interrupt code generated? I really just like to use the IWDG due to its low power (stop 2) capabilities, I don't want the WWDG at all. How can I activate the interrupt code generation for IWDG without activating WWDG? Is this intentionally or is this a bug in STM32CubeU0 MCU package in STM32CubeMx?ps. latest available versions installed (6.12.1 + STM32CubeU0 Firmware Package V1.1.0 / 05-June-2024) 

Updating the cubeide generates this error:An error occurred while collecting items to be installedsession context was:(profile=STM32CubeIDE, phase=org.eclipse.equinox.internal.p2.engine.phases.Collect, operand=, action=).Result of processing steps.OKOKOKPublic key not found for 70b824d9a6b4ae29.OKI could just intall the latest version, but I assume there is a way to fix this.  Thanks,Jamie

Hey, probably a dumb question, but I couldn’t find it in the datasheet. Can each pin of the VNQ9025AJ handle 30A, or is that the rating for the smart switch as a whole with a limit on each pin? Honestly, I’m hesitant to believe a single pin can handle 30A.

Hello,I want to activate UART1 interrupt directly through code in STM32CubeIDE, without using the .ioc file. UART1 is already active, so I just need to add the necessary lines to enable the interrupt.In the stm32wbxx_it.c file, I defined the interrupt handler as follows:void USART1_IRQHandler(void){/* USER CODE BEGIN USART1_IRQn 0 *//* USER CODE END USART1_IRQn 0 */HAL_UART_IRQHandler(&huart1);/* USER CODE BEGIN USART1_IRQn 1 *//* USER CODE END USART1_IRQn 1 */}In the stm32wbxx_it.h library, I declared the prototype as void USART1_IRQHandler(void);. However, I am still not able to receive data using the HAL_UART_Receive_IT function.

Hello STM community,I have a problem with my Nucleo-G431KB. I am trying to communicate to a sensor device over SPI. The problem I have is that when I use PA5 as SPI1_SCK, the logic high is only 1.4 V instead of the 3.3 V on other pins. When I configure PA5 as normal GPIO output I also get a 1.4 V output. When I use another pin as SPI1_SCK it works as expected. I have this problem when the Nucleo is connected to the sensor, but also when there is no load except for the oscilloscope.At first I thought that it might be a production error, but I have the problem on both of my boards.Is it normal that this pin has a lower voltage? If so, can I change it somehow? 

Hi,We're developing a PCB that can have multiple different I2C ICs assembled and have chosen the M24C02-RMC6TG EEPROM for board identification.In the datasheet, section 4.5, a note states no other device using the 1010 xxxx address can be connected to the same bus. The note also begins with "When using the DFN5 package:".I'm unsure whether this statement applies only for the DFN5 package or in general? (Datasheet snippet below)          One of the intended ICs that we plan to implement can be configured to have either 1010 011 or 1010 010 I2C address. Can this IC be on the same bus with this EEPROM? (With the address configured to not overlap with the other IC) Thanks in advance,Lazar

Question about HAL_SPI_TransmitReceive timeout.Currently, a timeout occurs when calling HAL_SPI_TransmitReceive in our program. (We are the master)What are some of the factors that cause a timeout in HAL_SPI_TransmitReceive?

Good morning,I'm using the STEVAL-MKI109V3 board associated with the STEVAL-MKI201V2.Is there a source code for using the STEVAL-MKI201V2 accelerometer with the STEVAL-MKI109V3 board?Otherwise there are examples of using the STEVAL-MKI201V2 with other microsprocessors? Thank you.Best regards.Gb2. 

Hi STM Expert, We are currently working on STM32G491KCU6 MCU FDCAN side. Our requirement is to validate the activity on Tx and Rx pins. We started off the testing with the LoopBack mechanism but unfortunately we were not able to see any data received in the Rx buffer. We referred sample FDCAN programs for this and tested the same in STM IDE Debugger mode. We then moved to test the normal mode as well. For this we used a sample code and probed the Tx pin of FDCAN using an oscilloscope. During the transmission, no activity is seen on the oscilloscope. We confirmed the pins are not damaged by setting FDCAN_Tx and FDCAN_Rx pins to GPIO and toggled it.   Please let us know what we have missed and guide us.