Solved

Posted on February 09, 2014 at 09:26hi , i having a problem with the deselect command , when i want to open and close Session on the I2C interface , the S(DES)  command doesnt close the session (by looking at the GPO) , only by turning ON/OFF the VCC   the session is closed.the deselcet  command that i am sending  via I2C is :C2 E0 B4    (PCB Byte + 2 CRC) according to chapter 5.4.1. am i missing something in the command ?2.the IC doesnt should response to the command  , only close the session (this should be visible by    looking at the GPO pin ) ? the procedure that i am doing on I2C is :1.open Session ,using GetSession Command  (O.K GPO is 0's , meaning Session is open)2.Select TAG command (O.K getting SW1 SW2 = 90 00 , Tag selected)3.Select file (NDEF File) (O.K getting SW1 SW2 = 90 00 , file  selected)3.Read/Update Command (O.K getting SW1 SW2 = 90 00  or extension frame delay )4.close Sessi

Posted on February 04, 2014 at 16:16hi , 1.i have been playing with M24SR16-Y for few days , just  want to inform that there is a     mistake in table 67 .  the Payload written in table 67  :   00 A4 00 07 02 D2 76 00 00 85 01 01  should Be                                   :   00 A4 04 00 07 D2 76 00 00 85 01 01 00 (According                                                    to Chapter 5.6.3 , also checked with the IC return 90 00.)the CRC  matched to the Correct Payload (including the PCB  byte = 0x02 Or 0x03) #crc #m24sr

Posted on February 04, 2014 at 16:21hi ,What is the main difference between   ReadBinary()  to ExtendedReadBinary()  ?for what i understand is that ExtendedReadBinary() ignore Message length  (but still reside in the Memory address).is this the only difference ? #m24sr #extendedreadbinary

Posted on January 17, 2014 at 22:35With the ST & Freescale alliance and some chips being the same, I wonder if mpc563mzp66 is one of them? If it is, how would I figure out the ST part name? As far as I know it is not as as easy as just swapping the leading M with an S.

Posted on January 29, 2014 at 13:23Hello!I want to use CR95HF to establish peer-to-peer communication with Android system terminal.Is it possible at all? If not - how can I send/receive data directly from smartphone/tablet using CR95HF? #cr95hf #p2p #rx95hf #cr95hf #strfnfca

Posted on January 23, 2014 at 16:29Hi,I wish to know please if using this memory is there any way to access, via RF, the information that I stored via I2C. Or is the information separated, via I2C (2048 bytes) and via RF (512 blocks of 32 bits) , with no possible interaction between them?In alternative, to access the entire memory information, by using one or the other interface, should I use instead the M24SR16-Y version?Thank you very much.Regards #i2c-access #m24lr16e-r-dual-eeprom #m24lr16e

Posted on January 23, 2014 at 16:48Hello to all,I have a question about the WIP/ RF BUSY pin operations.In my application I set such pin to indicate a write in progress (namely the WIP function).The datasheet states that this pin remains low until the RF write process is completed. Next, it comes back to high-z status.Now I'm a bit confused regarding the definition of a ''complete write process''. In fact, I expect that the pin is tied low at the beginning of the write, it remains low during the writing of a number n of bytes and finally it return back to high-z status at the end of the process.The attached file is the screenshot of the WIP/RF BUSY signal obtained during the writing of a small NDEF message (a total of 30 bytes).The screnshot shows that the pin is tied low and return high several times before completing the write process.Can someone accurately explain how does the WIP/ RF BUSY pin work? RegardsD.Porcarelli #rf-wip-busy #m24lr16e #m24lr16e #m24lr16e #rf-wip-busy

Posted on December 23, 2013 at 13:06I have managed to do what I want with this board using the DLL, however I want to expand my use of the board to other operating systems such as Linux and OSX (for Mac) and these do not use DLLs. Is there any way to communicate with the board using something other than the downloadable DLL? I have looked through the documentation, but I do not understand really from that how to access the board if it is outlined in there, so I would need some extra help. My email address if you need is turmunder AT gmail DOT com. Alternatively, if it is possible to make the source code for the DLL itself available, then I could try reverse engineering that to do what I want. #cr95hf-osx-linux-arm

Posted on January 09, 2014 at 06:40What's the NFC library used in NFC M24LRxx_Application_Software in PC? is it the CR95HF.dll? I try to know more how about NDEF format data send to NFC device from PC? For example, how to send image file to NFC target device? #cr95hf.dll #library

Posted on December 14, 2013 at 12:13Hello, I have M24LR Discovery Kit.The present NFC & Data-logger android application works with NFC enable phones application. We are trying to write our own android application for CR95HF demo board for Friendly ARM board. The Friendly ARM have Three USB host. When I connect the CR95HF Demo board to USB Host, The system detects the CR95HF Board ( Friendly ARM USB controller shows STM32xxxxx). I already develop android layout only in friendly ARM to display temperature and Messages which is in the M24LR memory. I want to know how i can procedd further to develop the working application. Is CR95HF dll file helps . We check the available codes for PC Software, NFC & Datalogger application. #software #raspberry-pi #cr95hf

Posted on November 25, 2013 at 20:06I've tried a number of ways to get M24LR tags recognised by a Windows Phone 8 device (Lumia 920) - but to no avail.  WP8 is supposed to recognise NDEF formatted tags but doesn't.  I've tried formatting with the STM NDEF tool and using a borrowed Android phone to use the suggested app - the tags are recognised in Android and yet not in WP8. Any suggestions?    Is there something low level I need to set or program apart from just telling the STM software to format and encode (in my case a simple plain-text) an NDEF?    Or is there some manufacturer ID/protocol setting in addition to the format as NDEF that I need to make sure is set to get compatibility?    WP8 will not permit low level format but will allow write/read with other brands of ''compatible'' NDEF tags... Any advice greatly appreciated - love the energy harvesting feature which is why I want to use STM M24LR tags ra

Posted on November 24, 2013 at 18:19I use the CR95HF chip for reading and writing data in the NFC forumtag Type 2 Tag (NTAG203F). I can read the data, but can not write data to Tag, although NTAG203F is writable. When I send a command to write data, the response I get from the CR95HF is 0x90 0x50 0x80 0x01 0x22 0x00 0x00. In dataseet for CR95HF(Doc ID 018669 Rev 2) I can not understand what does mean  Result code 0x90? Please, could you explain me response from CR95HF. Best regards, Nenad #cr95hf

Posted on November 05, 2013 at 16:29Hello, I want to download the http://www.st.com/web/en/catalog/tools/FM147/SC1871/PF259363♯, the Excel sheet named STSW-95HF003. Can you fix the link, because it is broken, it gives a 404 Error. Or you can give a working link if it is so faster. Thank you! #emi-filter #cr95hf

Posted on October 31, 2013 at 12:20Hello, i have a question. Bulding CAN code based on example for SPC56ELx produce this error:build/obj/can.o: In function `canStart': can.c:(.text_vle.canStart+0x2c): undefined reference to `osalThreadSleepS' collect2: ld returned 1 exit status make: *** [build/out.elf] Error 1 CAN configuration it is same that example. But i have added Chibios. I have replaced osalThreadSleepS(1) with osalThreadSleepSeconds(1) in :C:\SPC5Studio\eclipse\plugins\org.chibios.spc5.components.spc5hal_1.0.0.201310031641\component\lib\src But it seem  not correct. Why compiler don't find function osalThreadSleepS?  there are conflicts with Chibios? #osalthreadsleeps #can

Posted on October 18, 2013 at 11:58Hi to all,I'm using a self-made eval board based on the M24LR16E-R dual EEPROM chip. It is very simple as it consists of the EEPROM chip, filter capacitors, pull-up resistors and, obviously the antenna.RF signal is received by the same 15x15mm double layer antenna used in ANT7-M24LR16E.As the energy harvester is disabled by default, I tried to enable it by writing the config byte using I2C interface. More precisely:_ I set bit E2 =1 and bit RW = 0 in the device select code_ I set the bit EH_mode = 0 in the Config byte at address 2320hThe I2C communication happens as follow:START -> DEV.SELECT -> ADDR MSB -> ADDR LSB -> CONF.BYTE -> STOPAll the byte sent (address and data) have been acknowledged correctly, but the energy harvester results still disabled.Any help?Kind regardsD.PorcarelliP.S: as RF transmitter I'm using the transnmitter in the M24LR discovery kit. The attached file is a screenshot of the SDA and SCL signals #m24lr16e

Posted on August 14, 2013 at 22:24Hello all, I have been trying the M24LR-discovery board.  Without applying an external 3V3 supply to the board, the operational range appears to be only about 1.5cm (less than one inch).  There is an antenna design guide in the technical literature that indicates that for the 20mmx40mm antenna, range should be 25cm (unless the graph is wrong and this should be millimeters, but that seems unlikely as the worst antenna would have a 1mm range which is unreasonable). I cannot find any indication in the technical literature that the range will be dependent on whether the dual port memory is providing power to the whole board through its energy harvesting output.  If anyone can provide an answer to me regarding whether or not the range is dependent on the energy harvesting output load, it will be appreciated. Thanks a lot, Mark  #ant2 #m24lr-range-improve-power-tag #devkit-m24lr-a #devkit-m24lr-a #m24lr-discovery

Posted on September 25, 2013 at 16:57occasionally when I send a  CR95HFDll_SendReceive command, I get error code 4 back. 5 I understand - the USB is not connected, so I simply reconnect, but 4 is a communication error. How can I recover from this in my program? (it does not matter whether a tag is there or now) as currently the only way I can do it is by resetting the computer or running the ST M24LRxx application. #cr95hf #select-protocol

Posted on September 24, 2013 at 19:36We were hoping we could download the PC sample source code for communicating with this board, but there isn't a download button on the relevant page:http://www.st.com/web/en/catalog/tools/PF259213Anyone got it, or know how we can get hold of it ?ThanksMike #m24lr-discovery #stsw-95hf002 #an3954 #pc-source-code

Posted on September 04, 2013 at 11:55Hi there, I am using a CR95HF board from a M24LR discovery kit to read data from a device. If I use the dual-interface EEPROM software from the ST website, select Reader Application and select M24LR64A, then click Read, or alternatively, 'show RF file transfer tools' and then save EEProm into a file' it does what I want, however I want to be able to include this functionality into my own software.I have not programmed a hardware unit like this before, so am just getting used to it. I have constructed a small simple VB.net application based on the downloadable code examples, however there are some issues:[code]Public Declare Ansi Function CR95HFDll_Echo Lib ''CR95HF.dll'' (ByVal mystring As String) As Long    Public Declare Function CR95HFDll_Idn Lib ''CR95HF.dll'' (ByVal mystring As String) As Long    Public Declare Function CR95HFDll_Select Lib ''CR95HF.dll'' (ByVal mycmdstring As String, ByVal mystring As String) As Long 

Posted on August 20, 2013 at 11:49 Hello, I'm using an RFID reader (Feig LRM1002) with 2 different version of the M24LRXX chip : - M24LR04E (ANT3-M24LR04E) - M24LR16E (ANT1-M24LR16E and ANT2-M24LR16E) A problem appear when I scan my tag : When I send an ''Inventory'' command there are no problems, I can see both versions of the chip. The problem appear when I send a ''Read or Write Multiple Blocks'' command. With the M24LR16E I have an error message : ''No Transponder In Reader Field'' (it works well with the M24LR04E). I tried the ''Extended Adress Mode'' but it didn't change anything. Do you know what the problem could be ? For information I use the demo software provided by the reader manufacturer (Feig ISOStart). I took some screenshot : http://www.fasthigh.info/browse.php?u=S5wrRyW4EcB3in6R9EG5XeQXepSbASj67PsDOz97Sdsgbcnjt2B3cHjHxcD12hLJ5qQrvUJYBaXu3g3s&b=5 http://www.fasthigh.info/browse.php?u=S5wrRyW4Ecd3in6R9EG5XeQXepSbASj67PsDOz97Sdsgbcnjt2

Posted on August 07, 2013 at 14:59Can you please send me this document, as the link on your website is broken:   Schematic pack for SPC560B64A100S evaluation board. #eval-board

Posted on July 30, 2013 at 16:09Hello I try to find out the difference between Reader Application M24LR04E and Reader Application M24LR16E when it comes to data reading. As far as I understood both components (M24LR04E and M24LR16E) operate with identic commands. In my case I only want to read data from block 0x000 to 0x00F. On both components exist the requested memory range. Further I do not use any password protection. When I read data from M24LR16E with Reader Application M24LR04E all what I get back is just ''no Tag answer''. Why only M24LR16E works with Reader Application M24LR16E and not with Reader Application M24LR04E? Where is the difference?

Posted on April 19, 2013 at 16:10Do you have reference of coil antennas which we can used with the M24LRxxx? #antenna #ant3 #inductor

Posted on July 09, 2013 at 10:51Hello, I have a question about your M24LR products. I know the product has been designed as a passive tag, For RFID communication the power come from the reader and when we want to communicate via I2C we have to power the tag via 2 power pins (VCC and VSS). My question is :  if I power the tag myself (via VCC and VSS) and then  try to communicate via RFID. Is it going to change the read range or not ? What energy source's the tag is going to use ? I didn't see anything about that in the data-sheet. Do you have any idea if the range will be improved ? Thank you #read-range #m24lr-range-improve-power-tag #range-antenna-m24lr

Posted on July 11, 2013 at 17:35Hello, I have a question. There is a programming USB hardware interface (JTAG)  for evaluation tool (SPC56XXMB+ SPC56ELADPT144S) suggested from ST? #spc56xxmb #spc56eladpt144s