Solved

I am using touchgfx designer to create screens for my project, it works fine on visual studio. Then I try to port those cpp files to my atollic project. I got the following error:arm-atollic-eabi-g++: error: CreateProcess: No such file or directoryPreviously, atollic project was compiled. It has contained some screens already, so for adding new screens I don't need modify the directory settings. Anybody has an idea how come this error happens and how to solve it?Thanks in advance.

HiWhen I connect to the STM32WB55 nucleo(set up as peripheral) with my phone, I receive the EVT_LE_CONN_COMPLETE . Now I want to bond them with MITM, so I use aci_gap_slave_security_req() to let the phone know, I get a notification to pair, press pair, but then it keeps trying but doesn't work. In the documentation (STM32_BLEstack.pdf) they just say to use the command like that. Prior to the command(when not connected), I also set up the IO capability and authentication requirements like so:/**  * Initialize IO capability  */ BleApplicationContext.BleApplicationContext_legacy.bleSecurityParam.ioCapability = CFG_IO_CAPABILITY; aci_gap_set_io_capability(BleApplicationContext.BleApplicationContext_legacy.bleSecurityParam.ioCapability); /**  * Initialize authentication  */ BleApplicationContext.BleApplicationContext_legacy.bleSecurityParam.mitm_mode = CFG_MITM_PROTECTION; BleApplicationContext.BleApplicationContext_legacy.ble

I am trying to implement a star SPI interface, using STM32F4 as a single master, and interfaces with multiple STM32F4 MCU using SW managed NSS. I have made sure that SSI is cleared when NSS is activated and set when NSS is deactivated so that the SCK on the common line will not shift the data out of the deselected slave. However, I am still having corrupted data received by the master and I think the problem is due to the fact that the MISO pin of deselected slave is not in High Impedance state.While searching through the forum, I stumbled upon a similar post https://community.st.com/s/question/0D50X00009XkZWvSAN/multislave-spi-using-stm32f7s, in which it is mentioned that the MISO of all slaves should be configured in Alternate Function Open Drain mode instead of Alternate Function Push Pull, in the Reference Manual of STM32F7.I gave it a try but the Master was then not able to read any data from the selected slave anymore. My questions are:Was the recommendation of making MISO AF OD

Hi,I am trying to design a power supply using eDesignSuite, having universal input from85~265VAC/50Hz and having 1 isolated output 10V@15mA and two non-isolated outputs 15V@75mA and 3.3V@50mA (flyback converter). But I am unable to design both isolated and non-isolated outputs in eDesignSuite. Could you please help me in this regard?Best Regards,Anayat 

Hi team,I would like to use the external interrupt for handling peripherals, but i didn't find the exact port pin of MCU. for example EXTI0 is an external interrupt pin which is located at?

..

Hi Team, I am using stm32h753 controller, While receiveing data in the UART. Rx buffer index is not always Rxbuff[0]. Data is received randomly in the different index. Here i am attaching the reference.

I tried booting via TFTP boot and got the following reply​BOOTP broadcast 1BOOTP broadcast 2BOOTP broadcast 3DHCP client bound to address 192.168.1.2 (766 ms)missing environment variable: pxeuuidmissing environment variable: bootfileRetrieving file: pxelinux.cfg/01-00-80-e1-42-56-51Using ethernet@5800a000 deviceTFTP from server 192.168.1.94; our IP address is 192.168.1.2Filename 'pxelinux.cfg/01-00-80-e1-42-56-51'.Load address: 0xc4200000Loading: #     0 Bytes/sdoneBytes transferred = 248 (f8 hex)Config file foundSelect the boot mode1:   Linux 4.19.9Enter choice: 1:    Linux 4.19.9missing environment variable: bootfileRetrieving file: uImageUsing ethernet@5800a000 deviceTFTP from server 192.168.1.94; our IP address is 192.168.1.2'.lename 'uImageLoad address: 0xc2000000Loading: *TFTP error: 'File not found' (1)Not retrying... for failure retrieving kernel​​this is my /tftpboot tree​.├── pxelinux.cfg│  ├── 01-00-8

The FatFS library references a BSP function to determine if a SD card is plugged in. Since I don't have a BSP for this PCB, CubeMX complains about the missing function. How do I generate a BSP that CubeMX will recognize to eliminate this configuration error?

I'm trying to print output to the console in the STM32 work bench, but I can't seem to get anything out, and with my lack of a logic analyzer the best I can do is confirm my calls to HAL_UART_Transmit return HAL_OK. Below is the minimal example I'm attempting:int main(void) { HAL_Init();   UART_HandleTypeDef huart3; huart3.Instance = USART3; huart3.Init.BaudRate = 115200; huart3.Init.WordLength = UART_WORDLENGTH_8B; huart3.Init.StopBits = UART_STOPBITS_1; huart3.Init.Parity = UART_PARITY_NONE; huart3.Init.Mode = UART_MODE_TX_RX; huart3.Init.HwFlowCtl = UART_HWCONTROL_NONE; HAL_UART_Init(&huart3);   HAL_UART_Transmit(&huart3, (uint8_t*)"HELLO\n", 6, 0xFFFF);   // Confirms that execution passed the transmit BSP_LED_Init(LED2); for(;;){ BSP_LED_Toggle(LED2); HAL_Delay(1); BSP_LED_Toggle(LED2); HAL_Delay(9); } BSP_LED_DeInit(LED2); }I've attempted to use both 9600 and 115200 baud across USART1, 2, and 3 (I found documentation that says 3 shoul

Hello everyone. Is there any offical and stable library for CR95HF?I haved tried to use X-NUCLEO-NFC03A1 package but no success. Below my schematic and i think it same as X-NUCLEO-NFC03A1.I can not get it work. Cant read dev id.Cant get work init function. What should i do? I attached my project files.

/******* Please check code snippet ************/int flag = 0;void EXTI_CONFIG(void){ //Enable clocks for GPIO and Sysconfig RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE); RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE); GPIO_InitTypeDef my_GPIO; EXTI_InitTypeDef my_EXTI; NVIC_InitTypeDef my_NVIC; my_GPIO.GPIO_Mode = GPIO_Mode_IN; my_GPIO.GPIO_OType = GPIO_OType_PP; my_GPIO.GPIO_Pin = GPIO_Pin_0; my_GPIO.GPIO_PuPd = GPIO_PuPd_DOWN; my_GPIO.GPIO_Speed = GPIO_Speed_2MHz; GPIO_Init(GPIOA, &my_GPIO); SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOA, EXTI_PinSource0); my_EXTI.EXTI_Line = EXTI_Line0; my_EXTI.EXTI_LineCmd = ENABLE; my_EXTI.EXTI_Mode = EXTI_Mode_Interrupt; my_EXTI.EXTI_Trigger = EXTI_Trigger_Rising; EXTI_Init(&my_EXTI); my_NVIC.NVIC_IRQChannel = EXTI0_IRQn; my_NVIC.NVIC_IRQChannelCmd = ENABLE; my_NVIC.NVIC_IRQChannelPreemptionPriority = 0x00; my_NVIC.NVIC_IRQChannelSubPriority = 0x00; NVIC_Init(&my_NVIC);}void EXTI0_IRQHandler(){ if(EXTI_GetITStatus(EXTI_Line

Hello,for a measurement task, I have to perform an ADC readout a certain time after a rising edge occurs from an external device.My idea was to use the HRTIM with an external event but I am unsure if it is possible to trigger a timer start with an EEV.I am using a STM32H743ZI currently on a Nucleo board with CubeMX with the MCU package 1.5.0.

..

hi i am trying to make a .stldr file to be able to external load the flash ic ,the mcu is 32f746ng and the flash is MX25L51245G , i tried to take one of the examples that provide with stmprogramer and change it to my configure , but unfortally i didnt get succes (not even a blinking led ) ,-so i wanted to know does anyone have some example project for this spsific mcu? (the provided example are for 32L ,maybe i dont doing right the transformaition).-is there a recommended project example that maybe will be more easy to make the changes and implent?(attached scheme)

Hi. I'm glad you're reading this, i hope you can help.Click-bait aside, i experience a nasty and unexpected behavior of external interrupts in a professional, industrial product designed around STM8AL318ATC.In short, there are 2 digital signals (from an encoder) input in PD2 and PD4 to which i want to react by triggering an IRQ on every edge.Pseudo-code with setup (macros that expand to proper register settings, i promise): EXTI_CONF1_PDHIS = 1u; // PD[7:4] used for EXTID IRQ EXTI_CONF1_PDLIS = 1u; // PD[4:0] used for EXTID IRQ // EN1_1 (encoder 0, signal A) REG_CR1(EN1_1) = CR1_INP_FLOAT; REG_DIR(EN1_1) = DDR_INP; REG_EXTI_CR(EN1_1) = EXTI_CR_EDGE_RISING_AND_FALLING; REG_CR2(EN1_1) = CR2_INP_IRQ; // EN1_2 (encoder 0, signal B) REG_CR1(EN1_2) = CR1_INP_FLOAT; REG_DIR(EN1_2) = DDR_INP; REG_EXTI_CR(EN1_2) = EXTI_CR_EDGE_RISING_AND_FALLING; REG_CR2(EN1_2) = CR2_INP_IRQ;...and the ISR:INSTALL_ISR(EXTID_vector, rotc_0_isr) {// I got here due to an edge on either EN1_1, EN1_2, or

Hi there, I have set up my STM32WB55 nucleo board up to work in the platform for my company. So far, the UART and GPIO are working. But I'm stuck on the BLE. I can set it up and find it with my phone, but when i connect to it, it doesnt get me an user event. I It's kinda strange because I get these IPCC_Rx interrupts in the APP_BLE_Init(), but when it starts advertising and I connect(which is working, i can read attributes on my phone) I don't get an interrupt. I also noticed that the timer that handles the connection state machine to restart the adversting when nobody connects to it, also doesn't work.I checked with the BLE_BloodPressure example from ST and when i connect to this, it generates an interrupt.Hope somebody can help me, I've been stuck for some days now on this problem

Hi all,I am experiencing some problem with PLL initialization using LL drivers.The code I am using for HSE, PLL and SYS clock is the following:void init_RCC_HSE(void) { //LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_GPIOH);   LL_RCC_HSE_Enable(); while(! LL_RCC_HSE_IsReady()) ;   LL_RCC_HSI_Disable();   //LL_RCC_HSE_EnableCSS();   LL_RCC_PLL_Disable(); LL_RCC_PLL_ConfigDomain_SYS(LL_RCC_PLLSOURCE_HSE, LL_RCC_PLLM_DIV_5, 200, LL_RCC_PLLP_DIV_2); LL_RCC_SetAHBPrescaler(LL_RCC_SYSCLK_DIV_1); LL_RCC_SetAPB1Prescaler(LL_RCC_APB1_DIV_4); LL_RCC_SetAPB2Prescaler(LL_RCC_APB2_DIV_2); LL_RCC_PLL_Enable();   while(!LL_RCC_PLL_IsReady()) ;   LL_RCC_SetSysClkSource(LL_RCC_SYS_CLKSOURCE_PLL);   SystemCoreClockUpdate(); }But the firmware stops after a few ms.What is the proper way to initialise it using LL drivers ?Thanks.s.

Hello,I'm working on a DCMI to USB Video Class Device converter for a project of my organization. The image sensor is a ultra low power custom design grayscale level with 640x480 resolution (8 bit per pixel). The DCMI acquisition is working and now I'm moving into the USB development.I want to clarify that I'm aware of the bandwidth limitation of the embedded USB FS PHY, however for now, few frames per second are enough, moreover I might consider to down sample the image in order to increase the frame rate.I found a github project holding an implementation of the USB Video Class Device for the STM32F4, I just turned it into makefile project (originally it was for IAR toolchain) and it works, which means that it streams a fixed image at low frame rate (8fps if I'm not wrong). This project is based on the Standard Peripheral Library for the F4 family.For RAM constraints I'm not using the f407, but the STM32L496 (however I might switch to another MCU if needed), then, to make the USB Vide

-----I FOUND THE ANSWER MYSELF. ----------Technical environment :-       Master : STM32F767-       Slave : M24256 EEPROM on custom board. SCL and SDA on PH4 and PH5 with 4.7K pull-ups-       CubeMX : V5.3.0-       Normal transaction is : MASTER do a 3 bytes WRITEHAL_I2C_Master_Transmit calls I2C_TransferConfig. Immediately after CR2 update two flags in ISR are set: STOPF ana NACKF. Write timeouts in I2C_WaitOnTXISFlagUntilTimeout. Logic analyzer does not show any activity. Both signals are high. Any ideas where to search for problem?

Hello i'm porting TouchGFX to a custom board using STM32F429 and a custom 800x480 16bit display.I'm having trouble when I try to add a .png image on the TouchGFX designer. For some reason, if the .png file have any gradient effect, the resulting image will not display correctly on the physical display.Here are some examples:This is the example application i'm trying to show on the display.This is how the colors are displayed on the physical display:Notice how the gradients effects are displayed on the display.My TouchGFX project is using the follow dithering configurations:# Optional additional compiler flags   user_cflags := -DUSE_BPP=16   # Settings for image converter output format   alpha_dither := yes   # Dither algorithms: 0 (no dither), 1 (Floyd-Steinberg), 2 (Jarvis, Judice and Ninke), 3 (Stucki)   dither_algorithm := 2   opaque_image_format := RGB565   non_opaque_image_format := ARGB8888Any suggestion on how to move forward? Thank you in adva

Hello every one.I am working with the STM32L4R5ZI. By default, it will uses MSI as the system clock source at 4Mhz.My question is: what will happen if I turn on HSI or/and HSE without turning the other clock source off?Thank you in advance?

I cannot get debugging working through the STM32CubeIDE. I can program the device using the OpenOCD debugger (but stepping through the code gives an error). However, I want to use the ST-LINK GDB server as the debugger, which does not work. I receive the following error:Target no device foundError in initializing ST-LINK device.Reason: No device found on target.I am incredibly frustrated with the lack of clear material for getting started. I was expecting to purchase the board, install any necessary drivers/tools, install the IDE, and start stepping through an example project. I prefer not to use the uVision IDE and was hoping that I am just not configuring the STM32CubeIDE correctly.

I am having a tough time getting a valid temperature reading from my STM32L051K8U6 MCU. This should be an easy task. I've spent a LOT of time Googling and believe I have everything setup correctly. Most of the sample code online is identical, but it does not work for me. Here is the code snippet I'm testing with:#define TEMP130_CAL_ADDR ((uint16_t*) ((uint32_t) 0x1FF8007E)) #define TEMP30_CAL_ADDR ((uint16_t*) ((uint32_t) 0x1FF8007A)) #define VDD_CALIB ((uint16_t) (300)) #define VDD_APPLI ((uint16_t) (330))   int32_t ComputeTemperature(uint32_t measure) { int32_t temperature; temperature = ((measure * VDD_APPLI / VDD_CALIB) - (int32_t)*TEMP30_CAL_ADDR ); temperature = temperature *(int32_t)(130-30); temperature = temperature /(int32_t)(*TEMP130_CAL_ADDR -*TEMP30_CAL_ADDR); temperature = temperature + 30; return(temperature); return(temperature); }     void ConfigTemperature(void) { RCC->APB2ENR |= RCC_APB2ENR_ADC1EN; ADC1->CFGR2 |= ADC_CFGR2_CKMODE;  

if (HAL_DAC_Start(&hdac4, DAC_CHANNEL_1)) { /* DAC conversion start error */ Error_Handler(); }   if (HAL_OPAMP_Start(&hopamp4) != HAL_OK) { /* OPAMP start error */ Error_Handler(); }   HAL_TIM_Base_Start(&htim7); // while(1) // HAL_DAC_SetValue(&hdac4, DAC_CHANNEL_1, DAC_ALIGN_12B_R, Dacbuffers[0][0]); if (HAL_DAC_Start_DMA(&hdac4, DAC_CHANNEL_1,(uint32_t *) Dacbuffers[0], DAC_BUFFER_SIZE, DAC_ALIGN_12B_R) != HAL_OK) { /* DAC conversion start error */ Error_Handler(); }Project is Cubemx generated. Everything works fine without DMA and i get result on DAC output. Trying to start DMA immediately stops with calling HAL_DAC_ErrorCallbackCh1. What can be the reason for this?Cubemx generated codeDAC_HandleTypeDef hdac4; DMA_HandleTypeDef hdma_dac4_ch1;   /* DAC4 init function */ void MX_DAC4_Init(void) { DAC_ChannelConfTypeDef sConfig = {0};   /** DAC Initialization */ hdac4.Instance = DAC4; if (HAL_DAC_Init(&hdac4) != HAL_O