Solved

Hi, With 'ctrl + H' on STM32CubeIDE, only c files in the workspace are retrieved.I want to search that includes header files, like a EWARM's 'ctrl + shift + F'If it is posible. plz tell me how.

I tried implementing a driver by following the Flash example present of the GitHub page and a blog I found online:How to Program Flash memory in STM32 » ControllersTechThe driver code according to this blog is: STM32/FlASH_PAGE_F1.c at master · controllerstech/STM32 (github.com)I tried to implement it for my application: Eeprom-Emulation-driver-STM32/FlASH_PAGE_F1.c at main · Yadnik1/Eeprom-Emulation-driver-STM32 (github.com)However, no data is being stored in the flash memory. I am making a mistake that I am not able to identify it, can someone please guide me with it.Thank you very much!!

I want to be able to have the Ethernet port on my board be configured as a link local address and be able to receive DHCP. How can I accomplish this?

I'm trying to follow the OSPI_NOR_MemoryMapped STM32CubeIDE example, but for a different device (W25Q128FV). Write Enable, Read Status, and Erase Sector commands behave as expected, as well as memory-mapped reads. This has been confirmed by monitoring the OSPI lines with a logic analyzer, and comparing against the W25Q128FV datasheet.The one thing that does not work is memory-mapped writes. No activity occurs on the OSPI lines; a fault occurs on the instruction to write to the OSPI1 address. The Cortex-M33 registers show a precise bus fault at address OCTOSPI1_BASE (0x90000000).Any suggestions are appreciated.OSPI_HandleTypeDef ospiHandle = { .Instance = OCTOSPI1, .Init = { .FifoThreshold = 1, .DualQuad = HAL_OSPI_DUALQUAD_DISABLE, .MemoryType = HAL_OSPI_MEMTYPE_MACRONIX, .DeviceSize = 24, .ChipSelectHighTime = 2, .FreeRunningClock = HAL_OSPI_FREERUNCLK_DISABLE, .ClockMode = HAL_OSPI_CLOCK_MODE_0, .WrapSize = HAL_OSPI_WRAP_NOT_SUPPORTED, .ClockPrescaler = 256, .SampleShifti

Good morning, for a repair I am looking for a data sheet for this TVS diode or a recommendation for the replacement. Many Thanks.

Usually peripherial SPI drivers support 3 delays to control signals timing:Delay from SS enable edge to first SCK edge (SS Idleness) - supported in STM32H7xxDelay between data (Inter-data Idleness)- supported in STM32H7xxDelay after SCK edge to SS disable edge (ASC in the picture) - seems to be not supported. Does STM32H7 SPI support the third delay?If not then, what is the value of it and does it depend on anything?Can it be modified directly or indirectly by a different attribute?

Hello,In the past we have utilised the system bootloader on the STM32F429ZIT6, to implement a command to allow firmware upgrades to be completed by the end user. As part of this, the command would configure an LED Driver IC to update an RGB status LED, giving the user an indication that they are in bootloader mode. This works great, and led to the assumption that the system bootloader does not reconfigure pins that are not used as by any of the interfaces listed in the application note AN2606, since if this was the case, the LED would not stay on since an enable pin needs to be held high by the STM32.We are now looking to implement the same firmware upgrade command on a different product that uses the STM32G473VET6TR instead, and have not had as much success.It appears as though once you enter the system bootloader, the LED enable pin (PD2) is reconfigured since the line is no longer being driver high by the STM32.For some context, I have included the function that we are using to swit

Hi!I have followed the tutorial on Youtube.•STM32L4 training: 07.3 Advanced peripherals - Hands-on DFSDM(L476) And now I have some data in playbuff.But I couldn't find any information about the data. Is there anyone knows what kind of format is it? Or Is there anyone knows how can I change these data in playbuff into wav.?Here are my current devices:Micro-Controller: STM32L496GDISCO

..

Hi, I have new custom board on STM32WL55CCU7. I can't flash/program with STM32CubeIDE. And when i try to connect with STM32CubeProgrammer with "Normal'" mode I have this error :"Error: Cannot connect to access port 1! If you are trying to connect to a device with TrsutZone enabled please try to connect with HotPlug Mode"  14:23:09 : ST-LINK SN : 002900213431511631343632 14:23:09 : ST-LINK FW : V3J10M3 14:23:09 : Board      : STLINK-V3MINIE 14:23:09 : Voltage    : 1,78V 14:23:09 : Error: Cannot connect to access port 1! If you are trying to connect to a device with TrustZone enabled please try to connect with HotPlug mode.And if i try to connect with "Hot Plug" mode I have this : 14:19:28 : ST-LINK SN : 002900213431511631343632 14:19:28 : ST-LINK FW : V3J10M3 14:19:28 : Board      : STLINK-V3MINIE 14:19:28 : Voltage    

I am trying to do RTC wakeup interrupt using STM32L412RBT6 microcomtroller in baremetal c, but the interrupt is not firing, below mentioning my code.int main(void){ LedConfig(); Tim6Config(); RTC_ClockConfig(); RTC_Init();  /* Loop forever */ while(1) { GPIOB->BSRR |= (1U<<13); Delay_ms(1000); GPIOB->BSRR |= (1U<<29); SysTick->CTRL &= ~SysTick_CTRL_TICKINT_Msk; RTC_SetWakeUpTimer_IT(RTC_WAKEUP_TIME_IN_SECONDS, WakeUpAutoClr); PWR_EnterStopMode(); RTC_DeactivateWakeUpTimer(); RTC_ClockConfig(); SysTick->CTRL |= SysTick_CTRL_TICKINT_Msk; }}void RTC_ClockConfig(void){ /* Enable Clock for Power interface.*/ RCC->APB1ENR1 |= (1U<<28); /*Disable backup domain write protection*/ PWR->CR1 |= (1U<<8); while((PWR->CR1 & (1U<<8))==0); /*Reset the Backup domain*/ RCC->BDCR |= (1U<<16); RCC->BDCR &= ~(1U<<16); /*Enable LSE Clock source and wait until LSERDY bit to set*/ RCC->BDCR |= (1U<&l

When using Send Data in Fast Transfer Mode with ST25DV64KC-DISCO and Android App ST25 Tap, communication will stop with an error if the data size is 200000 bytes.Is there a limit on communication size?

Do the MEMS LSM6DSD, LSM6DS3, LSM6DSO have better 'shock resistance' than the LSM6DSR?The following phrase CAN NOT be found in the LSM6DSR datasheet, but the comment is in LSM6DSD, LSM6DS3, LSM6DSO datasheets"High robustness to mechanical shock makes theLSM6DS3TR-C the preferred choice of systemdesigners for the creation and manufacturing of reliableproducts.."When testing we have observed better "shock resistance" in the LSM6DSD and LSM6DS3 than in the LSM6DSR.CheersWayne

Our application is not related to payment but more around NFC charging and tagging, we'll be using the X-NUCLEO-NFC06A1 (+ NUCLEO-L476RG) combination for the poller.Regarding the listener, we saw that the ST25DVxxKC lineup would be compatible. I'm not too familiar, but what would be the main differences between the ST25DV04KC, ST25DV16KC, or ST25DV64KC models? It seems the EEPROM is the main differentiator, but what implications does the capacity of this memory have on NFC performance? Are there cost/benefit tradeoffs?Also regarding a development board for the listener (for example the ST25DV64KC), what would be the appropriate choice? I see that there are three options: STEVAL-SMARTAG2, ST25DV64KC-DISCO, and ANT7-T-25DV64KC. Could you briefly explain what the differences would be and what the best choice for NFC charging/tagging development would be?Also, would the poller (ST25R3916) and listener (ST25DVxxKC) combination be WLC 2.0 compliant?

..

Hey There, iam using a LIS2DW12 on a STEVAL-MKI179V1 eval board :https://www.st.com/en/evaluation-tools/steval-mki179v1.html#overviewhttps://www.st.com/en/mems-and-sensors/lis2dw12.html#overviewThe Datasheet says that it has 50nA standbycurrent and 1-5 uA in oparation.Iam using the chip in single_data_conversion mode with softwaretrigger Iam triggering a measurement, reading the values over i2c and the chip goes to standby after that.The Chip offers 2 Powerpins VDD and VDD_IO .VDD has a consumption around 50-60nA in standby but VDD_IO has a current of 300-400 uA. The voltage is 3.3V.Any ideas where that high current is coming from?iam using SCL,SDA for i2c transmission, pin2 (CS) is pulled to VDD (activates i2c) and pin3 (sa0) is connected to GND (sets i2c adress)thank you!

OS : windows 10 home 64bit​stm32programmer version : 2.9There is a ".hex" file in the dropbox or onedrive path.Downloading to mcu flash forces stm32programmer to quit. If the ".hex" file is not in the dropbox or onedrive path, it is downloaded normally.This problem occurs from the version with built-in jre in stm32programmer. (v2.7 or higher)Versions below 2.7 will not be terminated.I tried several methods, but it doesn't work.Please help.

ST(Semiconductor) chip STM32F103CBT6, NRND(NOT RECOMMENDED FOR NEW DESIGNS) notice information has not been found on the website, how long is the remaining life cycle of this chip?When is the expected date FOR the manufacturer to notify NRND(NOT RECOMMENDED FOR NEW DESIGNS)?The ST official website found the promise of 10 years of supply, but now it has been 16 years of supply;

I Am facing another issue with this board.Her is my USB settingUSB_OTG_HS is Device OnlyNVIC SettingsUSB OTG EndPoint In/Out 1 INT checkedGLobal Int checkedUSB DeviceClass Virtual PortThen the init fails in USB_CoreReset with timeout.I checked the HAL_PCD_MspInit and pins looks OKay.static HAL_StatusTypeDef USB_CoreReset(USB_OTG_GlobalTypeDef *USBx) { __IO uint32_t count = 0U;   /* Wait for AHB master IDLE state. */ do { count++;   if (count > 200000U) { return HAL_TIMEOUT; } } while ((USBx->GRSTCTL & USB_OTG_GRSTCTL_AHBIDL) == 0U);   /* Core Soft Reset */ count = 0U; USBx->GRSTCTL |= USB_OTG_GRSTCTL_CSRST;   do { count++;   if (count > 200000U) { return HAL_TIMEOUT; <<<<<<<<<<<<< FAILS } } while ((USBx->GRSTCTL & USB_OTG_GRSTCTL_CSRST) == USB_OTG_GRSTCTL_CSRST);   return HAL_OK; }I just discovered that My USB config /**USB_OTG_HS GPIO Configuration PC0 ------> USB_OTG_

I'm having trouble getting TF-A to start from USB DFU using the STM32Programmer CLI. Here's what I get:$ ./xpro_uboot_prgm.sh ------------------------------------------------------------------- STM32CubeProgrammer v2.11.0 -------------------------------------------------------------------       Warning: Timeout is forced to 30000 ms     USB speed : High Speed (480MBit/s) Manuf. ID : STMicroelectronics Product ID : DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000 SN : 003B00403431510930393938 DFU protocol: 1.1 Board : -- Device ID : 0x0500 Device name : STM32MP1 Device type : MPU Revision ID : -- Device CPU : Cortex-A7   Start Embedded Flashing service       Memory Programming ... Opening and parsing file: tf-a-stm32mp153a-xpro-mp1-mx-usb.stm32 File : tf-a-stm32mp153a-xpro-mp1-mx-usb.stm32 Size : 220.38 KB Partition ID : 0x01   Download in Progress: [==================================================] 100%   File do

Hello, I am trying to open a project that can turn on the low power MCU stm32l031 with ANT7-T-25DV64KC while turning high and low periodically for GPO pin of the MCU. I tried many different ways but still not done with any of them (steval code and using NFC4 and 7 provided by stm32cubeide).Would you please suggest me for any reference or sample for St25DV-i2c?

..

In STM32F429ZI datasheet (DocID024030 Rev 10), in the beginning (page 1) it says:"LCD-TFT controller with fully programmable resolution (total width up to 4096 pixels, total height up to 2048 lines and pixel clock up to 83 MHz)". But in functional overview LTDC chapter (page 24) and STM32F4 reference manual (RM0090 Rev 19) LTDC chapter (page 480), they say  LTDC support resolution can only up to XGA (1024x768) resolution. Which one shall I believe, 4096x2048 or 1024x768?By the way, what is XGA​ resolution? Does it simply means 1024x768 pixels? If a LCD says it supports XGA resolution, does it mean this LCD has 1024x768 pixels?

Below is my code:uint8_t line[50]="Application is Running\n";uint8_t Buf[50];uint8_t A=0,B=0;  while(! HAL_GPIO_ReadPin(GPIOC, GPIO_PIN_13)); // wait for user button press  HAL_Delay(200);  strcpy((char*)Buf," \n\nI am in the Loop \n");  HAL_UART_Transmit(&huart1, Buf, strlen((char*)Buf), HAL_MAX_DELAY);  HAL_Delay(200);  strcpy((char*)Buf," Enter the number A : ");  HAL_UART_Transmit(&huart1, Buf, strlen((char*)Buf), HAL_MAX_DELAY);  HAL_UART_Receive(&huart1,&A, 2, 5000);  strcpy((char*)Buf," \nEnter the number B : ");  HAL_UART_Transmit(&huart1, Buf, strlen((char*)Buf), HAL_MAX_DELAY);  HAL_UART_Receive(&huart1, &B, 2, 5000);  sum=A+B;  sprintf((char*)Buf,"\n Number A = %d",A);  HAL_UART_Transmit(&huart1, Buf, strlen((char*)Buf), HAL_MAX_DELAY);  sprintf((char*)Buf,"\n Number B = %d",B);  HAL_UA

Hi I'm using STM32F407 development board. I want to syncronize TIM2 and TIM5. I've followed these instructions. Here is my TIM2 initialization function below:void TIM2Config (void) { /*************>>>>>>> STEPS FOLLOWED <<<<<<<<************ 1. Enable the TIM2 clock 2. Set clock division, enable auto-reload preload 3. ********************************************************/ //NVIC_SetPriority (SysTick_IRQn, 1); // 1. Enable the TIM2 clock RCC->APB1ENR |= RCC_APB1ENR_TIM2EN; // 2. Set clock coeff. as 2, enable auto-reload preload TIM2->CR1 = TIM_CR1_URS | TIM_CR1_CMS_1 | TIM_CR1_CMS_0 | TIM_CR1_CEN; TIM2->CR2 = TIM_CR2_MMS_0; TIM2->SMCR = TIM_SMCR_MSM;   TIM2->CNT = 0; TIM2->PSC = (uint32_t) 1-1; TIM2->ARR = (uint32_t) 26000000-1; TIM2->CCR1 = (uint32_t) 1300000-1; TIM2->RCR = (uint32_t) 0; TIM2->CCMR1 = TIM_CCMR1_OC1PE | TIM_CCMR1_OC1M_0 | TIM_CCMR1_OC1M_1; TIM2-&