About ASche.5

ASche.5 · 2024-12-04

every time I am changing CubeMX and generate code in my STM32H755 project in CubeIDE 1.6 it forgets to add the section with the drivers that is shared between the M7 and M4 cores I end up using git diff every time after CubeMx update. I this fixed in...

ASche.5 · 2024-07-31

I have been trying to get the debug setup running in CubeIDE 1.16 according to : dm00629855 Getting started with projects based on dual-core STM32H7 microcontrollers in STM32CubeIDE - Application noteAnd I was able do see the debug break point holdin...

ASche.5 · 2024-07-31

the ok button stays gray and I need to disable download working on STM32H7 dual core poroject. in CubeIDE 1.12 this was working

ASche.5 · 2023-05-15

Would need release dates for:L433 - guessing from searching around 2017L152 - guess 2015L552 - guess 2018L072 - guess 2016has anybody a way to find out or the data? Thanks a lot

ASche.5 · 2023-05-15

Since when is STM32L152RE LQFP64 NRND?From the looks best pin compile etc. would be STM32L552RE is there any overview for doing this transition. Else I would need to do detail compare my self but as these MCUs seem to be in one line I was hoping ther...

ASche.5 · 2024-12-04

@Alexshafi Thanks for the summery - I know but this is very bad tool behavior. So to your experience there is no better way then known the bug and working around it. @SofLit I need to stick to 1.16 for now project binding for now, but I will try it o...

ASche.5 · 2024-08-07

In the end it turned out that I did not used the SMPS supply. I was trying to port software that was running on LDO from H743. It is noted in the manual to the nucleo board H755 that only SMPS supply will work in default solder bridge SB setup but I ...

ASche.5 · 2024-08-06

Thanks for the hints and summery of the HSE options on the nucleo board. The problem that I faced was that I measured something obscure like 6-7MHz on the SB72 jumper. But after updating the ST-Link again I had 8MHz clock but a jitterd one, this was...

ASche.5 · 2024-08-01

I am confused how can this be done and changed in the V3 on Nucelo board that do not have a 8MHz base is there only the firmware update tool ? What else I just started with STM32H7 that has 25MHz base clock and I measure regardless of the settings in...

ASche.5 · 2024-08-01

Hi I am still struggling with similar problems here but one thing that made a huge difference is to not use default break point I assume the standard example will run into misalignment with the power domain wait. so set you break point below this on ...

User statistics

User Activity

cubeMX from CubeIDE in H7 dual core does not add driver in porject files

STM32H7 duble core debug to No device found on target.

can not disable Download step in Cube IDE 1.16

Where are release dates of MCUs are stored

STM32L152 is now NRND (since wehn) - what do us instead STM32L552RE is there a compare sheet ?

Re: cubeMX from CubeIDE in H7 dual core does not add driver in porject files

Re: STM32H7 duble core debug to No device found on target.

Re: How to change the (STLINK_V3E) MCO HSE Frequency

Re: How to change the (STLINK_V3E) MCO HSE Frequency

Re: STM32H7 debug dual core