About ALomb.1

ALomb.1 · 2022-07-11

The latest version of STM32CubeMx 6.6.1 organizes the parameters of the FDCAN differently from the previous version and shows useful information on Time Quantum, Time for one Bit and Baud Rate.But I think the displayed parameters are wrong, as shown ...

ALomb.1 · 2022-03-22

Form TouchGFX Designer 4.18.1 I created a simple application.I imported the project into the STM32CubeIDE (1.9) and added support for FreeRTOS.I have selected TIM7 as the timebase source.After calling TouchGFXGeneratedHAL::initialize() in file TouchG...

ALomb.1 · 2022-03-04

I try to add external loader to C:\ST\STM32CubeIDE_1.8.0\STM32CubeIDE\plugins\com.st.stm32cube.ide.mcu.externaltools.cubeprogrammer.win32_2.0.100.202110141430\tools\bin\ExternalLoaderIn debug configuration, check ExternalLodaer and than press Scan.Th...

ALomb.1 · 2021-07-12

My HW:NUCLEO-F446RECustom DISPLAY Board (TFT ILI9314, TPC TSC2007, SPI FLASH MX25R6435F)My SW:X-CUBE-TOUCHGFX 4.17.0STM32CubeIDE Version: 1.6.1STM32Cube_FW_F4_V1.26.1FreeRTOS 10.3.1 with CMSIS_V2Randomly and after some time (from 20 minutes to severa...

ALomb.1 · 2021-03-09

I would need to implement what is described in the attached image.Somehow I should "save" which button was pressed so that if the Pin/Password is correct go to the right screen.How can I do ?

ALomb.1 · 2022-10-12

No, I haven't found a solution yet, apart from not using the HAL_Delay.

ALomb.1 · 2022-03-23

Sorry @MM..1, but I don't understand what you are telling me :smiling_face_with_smiling_eyes: Do you think the interrupt configuration you asked me is correct ?Do you think that the timebase interrupt priority at 4 (despite I have set 0 in the CubeM...

ALomb.1 · 2022-03-23

The code stuck in HAL_Delay called in MB1642BDisplayDriver_DisplayOn after TouchGFXGeneratedHAL::initialize().If I remove the HAL_Delay the code correctly run.If I add an HAL_Delay before TouchGFXGeneratedHAL::initialize() the code not stuck.I can sh...

ALomb.1 · 2022-03-23

Interrupt configuration attached.I also noticed that the HAL_InitTick function is called three times:once from the HAL_Init with priority 0 (TICK_INT_PRIORITY);twice from SystemClock_Config (HAL_RCC_OscConfig and HAL_RCC_ClockConfig) with priority 4 ...

ALomb.1 · 2022-03-23

The timebase timer interrupt priority is set to 0 with "Uses FreeRTOS function" disabled.Is not correct?

User statistics

User Activity

STM32CubeMx 6.6.1 show wrong FDCAN Parameters Setting

Timebase no longer works after the TouchGFX Engine Initialization

Failed to list external Loader

allocateBlock never ruturn

How to implement PIN/Password check

Re: Timebase no longer works after the TouchGFX Engine Initialization

Re: Timebase no longer works after the TouchGFX Engine Initialization

Re: Timebase no longer works after the TouchGFX Engine Initialization

Re: Timebase no longer works after the TouchGFX Engine Initialization

Re: Timebase no longer works after the TouchGFX Engine Initialization