About EShaw.1

EShaw.1 · 2022-05-18

Hi All,Got it turning. Now need a guidance on where / what file and how I can control the speed. SDK 5.4.8.6S_STEVAL3202_SL_VM example.Monitor connects well.I can start the motor.Final ramp speed does not work. The only use - setting the direction of...

EShaw.1 · 2022-02-23

Look at this forum! Almost no one is getting answers for their questions from ST!I have received one answer from ST only. I guess I am lucky. Thank you. I asked 3 more questions - no luck.I have opened the case with online support, It was "escalated"...

EShaw.1 · 2022-02-22

Hi ST,I am unable to establish UART communication between ST MotorPilot and STEVAL-SPIN3202.I am uploading one of the two STEVAL-SPIN3202 examples.Setting up 9600 baud rate (same as in Cube MX settings). Using correct COM port.Hardware setup: Power ...

EShaw.1 · 2022-02-22

Dear ST,Could you please advice on the correct positions of STEVAL-SPIN3202 jumpers to run an example with ST MotorPilot.J9 - BOOT0 Open or closed? J7 - RX - TX Open or closed, Could you please explain why would we need to connect RX and TX? Which o...

EShaw.1 · 2022-02-21

Hi ST and fellow struggling customers:),I am trying to to get running small 24V BLDC sensorless in-runner with STEVAL-SPIN3202 in FOC or 6 STEP .I stuck after endless attempts with downloading various older versions of all the "cubes".I am trying (f...

EShaw.1 · 2022-07-31

Hi YNRUS,Sorry for a late reply.The generated code "as is" did not work for me. Alessio from ST kindly suggested to replace the code in one of the files as per thread:https://community.st.com/s/feed/0D53W00001Z7xFOSAZYou will need to replace this cod...

EShaw.1 · 2022-05-30

Hi Alessio,I am opening a new project in 5.Y.4.It is sensorless: When it is just open, It has Hall Sensors for the Motor and in Speed Sensing.Am I not allowed to change it to sensorless?Motor and Speed sensing in sensorless example should be sensorle...

EShaw.1 · 2022-05-25

Hi Alessio,The errors starting to pop up when I select Sensorless + PLL or other Sensorless in Speed sensing:C:/ST/Projects/6S_STEVAL3202_SL_VM/Src/mc_config.c:47:43: warning: initialization of 'short unsigned int' from 'void *' makes integer from po...

EShaw.1 · 2022-05-25

Hi Alessio!Thank you!Thanks to you I've made the biggest progress in 6 month with this board!I was able to download HAL (not LL) and it connects to Monitor!Thanks again!I'll be continuing my endeavors in the code to find how to control the board fro...

EShaw.1 · 2022-05-24

Hi Alessio,After replacing the code as instructed, I'm receiving error messages from compiler:12:02:47 **** Incremental Build of configuration Debug for project 6S_STEVAL3202_HS_VM ****make -j8 all arm-none-eabi-gcc "C:/ST/Projects/6S_STEVAL3202_HS_V...

User statistics

User Activity

STEVAL-SPIN3202. Got it turning. Now need a guidance on where / what file and how I can control the speed.

Why ST does not provide a support?

UART communication between ST MotorPilot and STEVAL-SPIN3202

STEVAL-SPIN3202 Correct positions of the jumpers

How to get started with STEVAL-SPIN3202 & Sensor-less BLDC motor?

Re: How to get started with STEVAL-SPIN3202 & Sensor-less BLDC motor?

Re: STEVAL-SPIN3202. Got it turning. Now need a guidance on where / what file and how I can control the speed.

Re: STEVAL-SPIN3202. Got it turning. Now need a guidance on where / what file and how I can control the speed.

Re: STEVAL-SPIN3202. Got it turning. Now need a guidance on where / what file and how I can control the speed.

Re: STEVAL-SPIN3202. Got it turning. Now need a guidance on where / what file and how I can control the speed.