About NR-A Comm

NR-A Comm · 2020-03-22

I tried to step-by-step execution based on UM2262. But I could not get SBSFU welcome screen display (Fig24). My SBSFU display below.[SBOOT] Flash Configuration KO: Dual bank mode activated. STOP![SBOOT] Security issue: execution stopped!My step-by-st...

NR-A Comm · 2019-11-01

My current development environment is as follows.STM32CubeMX v5.4.0, STM32CubeIDE 1.1.0, SW4STM32 1.17.0, Windows 10 1903.STM32CubeIDE Font SettingSTM32CubeMX Encording SettingGarbled C source code Japanese comments after code generationThank you in...

NR-A Comm · 2019-11-01

NR-A Comm · 2019-03-17

STM32CubeMX Board Selector does NOT show NUCLEO-G071RB, so I select MCU Selector and search STM32G071RB. STM32CubeMX shows NUCLEO-G071RB on Board Colum.I click NUCLEO-G071RB and I Start Project, Initializing all peripherals with their default Mode YE...

NR-A Comm · 2017-08-13

Posted on August 14, 2017 at 03:24PS2: I found my mistake that is Window value and Reload value are NOT set correctly. So questions are deleted.:( Thank you.Attachment is a project which I reworked WWDG_Example of STM32F072RB-Nucleo (STM32Cube_FW_F...

NR-A Comm · 2020-04-04

I can get Welcome Screen, by Option byte DBANK Off.Thank you everyone.

NR-A Comm · 2020-04-02

Thank you. Yes, I can disable [SBOOT] Flash Configuration KO: Dual bank mode activated. STOP!.But, I cannot still disable [SBOOT] Security issue: execution stopped!.Anyway, again I thank you for advice.

NR-A Comm · 2020-04-01

PS: I forget to attach reference.

NR-A Comm · 2020-04-01

Thank you for advice. I understood where printing ERROR msg.I tried and added define statement on sfu_low_level_security.c but it doesn't get Welcome screen.STM32CubeProgrammer User Configuration and PCROP are attached for your reference.I tried both...

NR-A Comm · 2019-11-04

I understand. Thank you.:D

User statistics

User Activity

STM32G4 SBSFU do not display Welcome screen

STM32CubeMX code generation causes garbled C source code Japanese comments in STM32CubeIDE. In the same way, the SW4STM32 does not display garbled characters. Please tell me how to avoid garbled characters in STM32CubeIDE.

Hello. How do I generate code by moving STM32 F0_FW v 1.11.0 back to STM32 F0_FW v 1.8.0? My current development environment is as follows. STM32 F0_FW v1.11.0, STM32CubeMX v5.4.0, STM32CubeIDE 1.1.0. Thank you in advance.

No GPIO on Nucleo-G071RB Pinout and Configuration

WWGD Debugging dese not work

Re: STM32G4 SBSFU do not display Welcome screen

Re: STM32G4 SBSFU do not display Welcome screen

Re: STM32G4 SBSFU do not display Welcome screen

Re: STM32G4 SBSFU do not display Welcome screen

Re: Hello. How do I generate code by moving STM32 F0_FW v 1.11.0 back to STM32 F0_FW v 1.8.0? My current development environment is as follows. STM32 F0_FW v1.11.0, STM32CubeMX v5.4.0, STM32CubeIDE 1.1.0. Thank you in advance.