Solved

Hi,I try to build up a HAM LoRa APRS system with STM32 and I don´t receive any messages in my gateway. For testing purposes, I use an 868 MHz gateway and an RAK3172 module. The RAK3172 module is configured as shown below:Initialize the LoRa module (use 868 MHz for testing)- Frequency: 868 MHz (868000000)- Spreading Factor: 12 (12)- Bandwidth: 125 kHz (0)- Code Rate: 4/5 (0)- Preamble Length: 8 (8)- Tx Power: 14 dBm (14)AT+NWM=0AT+P2P=868000000:12:0:0:8:14Transmit a coordinate point via APRS- Header: <FF01- Payload: DO2DKH-7>APLG01:!4932.05NL01047.50E&TestAT+PSEND=3CFF01444F32444B482D373E41504C4730313A21343933322E30354E4C30313034372E353045265465737432After transmitting the message via "PSEND" I receive it in my gatewayReceived packet 'Source: DO2DKH-7, Destination: APLG01, Path: , Type: Position Without Timestamp, Data: !4932.05NL01047.50E&Test2' with RSSI -40dBm, SNR 11.75dB and FreqErr 17145.003906HzI tried the same with my STM32WL55-Nucleo. I configured the RF switch pi

If I understand correctly, the BKPT instruction is "promoted" to hard fault when debugger is not connected.Is it possible to tweak STM32H7 so that BKPT will be silently ignored?-- pa

How to integrate PC-lint to STM32CubeIDE?

hello team,I'm using AutodevKit studio for testing AEK_AUD_C1D9031 board. I imported example code from sample : SPC582Bxx_RLA_AEK_AUD_C1D9031 - Avas Compact - Test Application.   but upon flashing board I'm getting this error. kindly provide feedback. for your reference I'm attaching log file. Mohit M

for custom board of STM32mp157f-dk2 version.the same code i run in the custom board it work but, the error " it stuck in the power supply type C not detected"  by Uboot , TFA and OPTEE work fine but in u-boot it stop so i can hand this situation and , any bypass mode is there.and where i can modify this one.Actually i remove the type C connector and in place of type C i attached the only two pin power supply in custom board ,after u-boot boots the MPU  , it prints the error on type C power supply  not detected, so in my code where i need to modify the code, i am using openSTlinux distribution package (STM32mp157f-dk2).

Hi Clive.I am running a project on the STM32H750VBT6 controller with external W25Q128 QSPI memory.I need to write data to flash. Your bootloader:https://github.com/cturvey/stm32extldr/blob/main/h7_w25q128/W25Q128_STM32H7XX-CUSTOM27.FLMdidn't work.I decided to write my own. It works, but strangely. It works at first, then it can stop workingIt can be cured by commenting out an unused function or changing the optimization type.It works for a while, then it stops. And I have 2 identical boards. It works on one,on the other it doesn't.I ask for help. I am attaching my project. What could be the problem?If not, can you fix your bootloader W25Q128_STM32H7XX-CUSTOM27.FLM ?It doesn't work for me.

Hello All,   I am reaching out to seek assistance regarding an issue I encountered while attempting to upload the BLE stack to my STM32WB device using the STM32 Cube Programmer. Below is the sequence of commands I executed:STM32_Programmer_CLI.exe -c port=usb1 -fwdeleteSTM32_Programmer_CLI.exe -c port=usb1 -r32 0x20030030 1STM32_Programmer_CLI.exe -c port=usb1 -fwupgrade stm32wb5x_FUS_fw_1_0_2.bin 0x080CB000 firstinstall=0STM32_Programmer_CLI.exe -c port=usb1 -fwupgrade stm32wb5x_FUS_fw.bin 0x080CB000 firstinstall=0STM32_Programmer_CLI.exe -c port=usb1 -fwupgrade stm32wb5x_BLE_Stack_full_fw.bin 0x080CB000 firstinstall=0Unfortunately, when executing the final command, I encountered the following error:Error: failed to download Segment[0]Error: failed to download the FileError: Failed to download image! I have successfully executed the prior steps without issues. However, the BLE stack upload process is failing, and I would appreciate your guidance on resolving this error. If there

I want to align digits without prepending with 0. So %3d instead of %03d. 000:00 100:00 10:00 1:00 With non-monospaced fonts, such as verdana this doesn't work due to the space character not having the same width as digits. I don't care about the width of punctuation. All digits do have the same width in most non-monospaced fonts, but the space differs.Unicode has different space types. Such as U+2007 "FIGURE SPACE" (https://jkorpela.fi/chars/spaces.html). This character should be a space character with the same width as a digit. Not all fonts support this character(https://www.fileformat.info/info/unicode/char/2007/fontsupport.htm). Arial is non-monospaced, but supports this character.Below is a demonstration with ARIAL with regular space and "FIGURE SPACE"WWW:WWlll:ll000:00100:00 10:00  1:00WWW:WWlll:ll000:00100:00 10:00  1:00As you can see (if the forum renders this correctly) the width of characters differs, but digits have the same width. And the "FIGURE SPAC

Is there any example on STM32H503 nucleo board, how to handle USBX with storing/reading data from pendrive?

Hi, first time using DMA so just reading various datasheets and posts. But something is not clear.   I would like to use DMA with UART to send large amount of data through the serial port while keeping the CPU as free as possible for other intensive tasks. So I am thinking of using HAL_UART_Transmit_DMA() but, because of the large amount of data that needs to be sent, I might need to call HAL_UART_Transmit_DMA() very often with the risk to it being called while the previous HAL_UART_Transmit_DMA() call/operation is still running.   Is there a way to somehow append - or perhaps automatically queue - the new data right at the moment I need to so the code can keep executing, instead of having to wait and check for when the current DMA action is completed (whether inline or through interrupts)?   Also is there a limit to the data size I can send with HAL_UART_Transmit_DMA() ?   Perhaps using two channels? Thank you

Hello,My new NanoVNA-H4 arrived today.  I immediately set out to update its firmware to the latest version (v1.2.29) but have been unable to get the DFuSe_Demo_V3.0.6 bootloader to "Choose" the DFU file (NanoVNA.H4.v1.2.29).  I get a "This file doesn't have a correct format..." error every time I make the attempt.  I therefore cannot update the firmware in my new NanoVNA. How can I fix this problem?See attached screenshot.Thank you,JS2OLO

Hello I want to communicate between cores using OpenAMP and HSEM and print the communication results using UART in the terminal environment.I'm currently using the STM32H757I-EVAL Board, and I have referred to the youtube link below.So my code doesn't generate compilation errors, but It doesn't print the results of between cores communication in the terminal environment.Any help is greatly appreciated! Friendly regards, Tau Reference : STM32 Dual Core #3. Inter core comm using OpenAMP and RPmsg || IPC || Shared Memoryhttps://www.youtube.com/watch?v=hKiVYq0EaS4

Posted on September 21, 2017 at 11:08Good moring,Regarding the SensorTile source code example, i saw the BLE_SampleAmpl and the DataLog examples. But is there the native source code related to the native application of the SensorTile kit that provides all the sensors information through Blue NRG?Thank you#sensortile-kit

Hello, I have created a project in TouchGFX 4.24 based on the STM32U5A9J-DK I am using. I generate the code in TouchGFX and then import the project into STM32cubeIDE 1.16.0. The code will build and compile and I am able to upload it to the board and everything works as expected.  When I open the .IOC file to add PE2 as a GPIO_EXTI2 interrupt and generate the code the project will no longer build with the following 2 missing files:C:/ST/STM32CubeIDE_1.16.0/STM32CubeIDE/plugins/com.st.stm32cube.ide.mcu.externaltools.gnu-tools-for-stm32.12.3.rel1.win32_1.0.200.202406191623/tools/bin/../lib/gcc/arm-none-eabi/12.3.1/../../../../arm-none-eabi/bin/ld.exe: cannot find -l:libnemagfx-float-abi-hard.a: No such file or directoryC:/ST/STM32CubeIDE_1.16.0/STM32CubeIDE/plugins/com.st.stm32cube.ide.mcu.externaltools.gnu-tools-for-stm32.12.3.rel1.win32_1.0.200.202406191623/tools/bin/../lib/gcc/arm-none-eabi/12.3.1/../../../../arm-none-eabi/bin/ld.exe: cannot find -l:libtouchgfxnema-float-abi-hard.

Hi, I have a problem when using scroll list as a menu list. I have a custom container( a textArea and a background image) for this scroll list. It works good but this lagging problem. I'm running on NucleoG071RB + X-NUCLEO-GFX01M2, I know this resources are quite limited in this board. I tried to make the background as a 200*4pix thin line, still has this lagging problem.Any thoughts? thanks in advance.What I haved tried:1- make the background as small as possible (not working)2- setAnimationSteps(0), (not working, not related to this problem)I uploaded a video to make it easy to get the intuition of this problem. 

I removed the STlink of the NUCLEO F722ZE board and wrote it, but there was a clock error, so the program itself is not working It worked normally when there was Stlink, but it's not working I set it to HSI and used it, but it didn't work, so a clock issue occurred to switch to HSE, so I thought it would be okay to just debug it, but at some point, the clock didn't work, so it didn't come out of stop mode I set it as an rtc alarm and woke it up, but it seems like a clock error when it stops after going well How can I fix this error? Stlink uses a lot of electric current, so it needs to be removed I removed only the stlink from the hardware, but this is the situation Original settings before removing STlink       Setting changed to clock error after removing STlink       This is the setting I used before, but after removing the STlink, the HAL_RCC_OscConfig(&RCC_OscInitStructure) error handle occurred in this part   void SystemClock_Config(void

Hello,I am working on project with:STM34F405RG6 board and TFT Display GC9307 driver using CubeMX V6.12, Keil uVision v5.40 (ArmClang v6.22), and TouchGFX v4.24LCD Driver working library used: https://github.com/Floyd-Fish/ST7789-STM32/blob/master/README.mdusing SPI communication, Half Duplex Master Framebuffer strategies: Partial Frame buffer First, I tried test function in driver above with my board and working just fine displaying colors, fonts, and images. then I want to run my board with 100MHz clock and using CRC (because it's necessary for TouchGFX).Second, I tried change the configuration, using 100MHz Clock and CRC, my board displaying test function just fineThird, I Added TouchGFX through CubeMX without Changing any configuration, before adjusting the driver I want to check is the previous LCD driver working. so I make blank function of:  void touchgfxDisplayDriverTransmitBlock(uint8_t* pixels, uint16_t x, uint16_t y, uint16_t w, uint16_t h); uint

Hallo,I'm using U5A9NJQ demoboard with FILEX. I have something that doesn't work, the first time I write on a file, all is correct, but if I rewrite on the same portion of the file, the writing seems to be correct, but, when reading, the content hasn't changed. Do you have found something similar? Is there a project where is possible to have the FILEX working with this demoboard?Thank you

I'm working on a design that involves using an STM32F04 acting as a USB-CDC to RS232 bridge to communicate with the main logic of the system, in preference to dedicated RS232 USB chips that require dedicated drivers. In addition to this, the STM32 is also driving an I2C device and bridging it over SPI to the main logic. All of this works well. The I2C is also connected both to the CPU and the main logic, though the main logic does nothing with this interface normally, but allows me to test the issue below.When I came to investigate having the main logic update the firmware of the STM32, I identified an issue - though I was able to boot the STM32 into its ROM bootloader, I can't actually access it - it doesn't respond on the I2C or the UART.Having consulted AN2606, it lists the following ports as used by the bootloader in the STM32F04:- PA11 (USB-)- PA12 (USB+)- PA9 (USART1 TX)- PA10 (USART1 RX)- PA14 (USART2 TX)- PA15 (USART2 RX)- PB7 (I2C1_SD)- PB6 (I2C1_SCL)However, the TSSOP20 packa

I am triggering adc every 100us in dma and getting data in adc callback. I am triggering adc with hrtim compare 3. //hrtim cmp3 event call back{//reset a pin.} //adc conversion call back{//set a pin} for some reason the reset pin is working every cycle but set pin skips its cycle.It means adc call back not working every cycle?What can cause this kind of behavior?

Hi,I am using built-in usart bootloader on stm32g0. And I am also using the same usart for communication in my user app. I enabled the bootloader via boot option bits. When I start the debug session, I can see the flow stepping over through the program flow, going over HAL_Init(), SystemClock_Config(),  MX_GPIO_Init() and MX_USART1_UART_Init(), and then the program flow comes to my first "HAL_UART_Receive(..." function. It is at this function that the program jumps to the Bootloader and the bootloader starts to respond to my uasrt commands. After I exit the bootloader, via the "Go command(I use address 0x08000000)", the program flow stops at breakpoint I have at "HAL_Init()" and then when I step over again, I see that as soon as I hit the "HAL_UART_Receive(..." function again, it goes back into bootloader. So, my thinking now is that after I exit the bootloader, I should modify the boot bit (nBOOT0) in my user code, to disable it and then enabling it again

Hi, I have some problem about IAP.It's not working application after jump from custom boot. - MCU : Stm32F446RC- Board : Custom board- Boot address : 0x08000000 ~ 0x0801FFFF (128k)- Application address : 0x08020000 (384k) - Custom Boot Flash.ld - Application Flash.ld - Application system_stm32f4xx.c- Jump to App code I got the problem here- HAL_Init() -> HAL_InitTick(TICK_INT_PRIORITY) -> HAL_NVIC_EnableIRQ(TIM8_TRG_COM_TIM14_IRQn) in stm32f4xx_hal_timebase_tim.c Anyone have some solution?Please answer me. Thanks.  

I'm writing a code for getting angle from a AS5047u magentic encoder to get the angle but the value from the angle not seems to be updating in the live expressions

Dear Community,When comparing STM32L5x2 line with STM32U5x9 line I had the surprise to read in product selector's view:Supply Current Run Mode (per MHz) typical:- For STM32L5x2:    96- For STM32U5x9:   26Are these numbers correct?If yes, what can explain those differences (nearly 4x) between the two lines of MCUs?Kind regards,dom

Hello everyone, I hope you can help me!!! I'm at the beginning of programming in C++, and I'm having difficulty taking a variable from my main.c file to my screen created in touch gfx. This error appears, where it apparently does not find the variable declaration. Run SimulatorGenerateDoneGenerate Assetsmake -f simulator/gcc/Makefile assets -j8Reading ./application.configReading ./target.configDonePost Generatetouchgfx update_project --project-file=simulator/msvs/Application.vcxprojDonePost Generate Targettouchgfx update_project.cproject file: ../STM32CubeIDE/.cprojectWriting STM32CubeIDE project file: ../STM32CubeIDE/.projectWriting STM32CubeIDE project file: ../STM32CubeIDE/.cprojectDoneCompilemake -f simulator/gcc/Makefile -j8Reading ./application.configReading ./target.configLinking build/bin/simulator.exebuild/MINGW32_NT-6.2/gui/src/monitor_screen/MonitorView.o: In function `ZN11MonitorView15handleTickEventEv':C:\TouchGFXProjects\MyApplication_2\TouchGFX/gui/src/monitor_scree