Solved

I created a custom application using the code from the BLE_THREAD_DYN example and the v10.0 FW BLE_THREAD_DYN stack. The BLE works fine but the thread stack goes down after a few minutes. The main differences between my code and the example is that I converted the code to use FreeRTOS but I preserved most of the logic and structure. Upon initial system power on, the stacks both initialize and go up just fine with the device meshing with my existing thread network. However, after a few minutes the device disconnects from the thread network and the node never reconnects but the BLE remains active. I'm troubleshooting the issue but any breadcrumbs on how to converge on the problem more quickly would be much appreciated. Update 3/3/2021 @ 1:50PMWithin the initialization of both stacks, I commented out the BLE initialization and only ran with the Thread stack active using the v10.0 BLE_THREAD_DYN firmware. The issue persisted with the Thread stack going down after a few minutes -- the amoun

Hello,LIS2DH12 accelerometer. Datasheet AN5005 shows Table 4.Is this the speed of data transfer via the SPI or I2C interface? Or the speed of converting data into accelerations and writing this accelerations to the OUTX_H and OUTX_L registers?

Hey all,I am facing problem in configuring my board in I2c protocol. When  i configured the same board in standard mode it is working fine. Rest of the settings for pins(pull-up) ,rise time and fall time are same in both the files. Also attaching waveforms for both the mode. Can anyone suggest me what can be done to make the board work in fast mode as well.Thanking you in advance.

Hello here,I tried to use SWV for debug plotting in my project.I have STM32F103TBU6 and ST-Link V2.I turn on Trace Async Sw:My clock:In main.c I defined "stdio.h" and _write func:/* USER CODE BEGIN 0 */   int _write(int file, char *ptr, int len) { int i = 0; for (i = 0; i < len; i++) { ITM_SendChar((*ptr++)); } return len; }   uint8_t count = 0;   /* USER CODE END 0 */After I made while cycle with printf:/* USER CODE END 0 */   /** * @brief The application entry point. * @retval int */ int main(void) { /* USER CODE BEGIN 1 */   /* USER CODE END 1 */   /* MCU Configuration--------------------------------------------------------*/   /* Reset of all peripherals, Initializes the Flash interface and the Systick. */ HAL_Init();   /* USER CODE BEGIN Init */   /* USER CODE END Init */   /* Configure the system clock */ SystemClock_Config();   /* USER CODE BEGIN SysInit */   /* USER CODE END SysInit */   /*

When I configured development board's I2C I am receiving a short high pulse at 8th clock of SCL.I am attaching the waveform on scope following this post.Thanking in advance. 

Dear Sir, I have a NUCLEO-STM32G0B1RE board. I configure USART2 with CTS and RTS try to communicate with u-blox GSM module LARA-6004D, but fails. No data received.Is there any missing? Any comment are welcome, thanks.hardware connection isMCU TXD <-> GSM RXDMCU RXD <-> GSM TXDMCU CTS <-> GSM RTSMCU RTS <-> GSM CTS IOC config about USRAT2 are as fillows, 32:Mcu.IP4=USART2 65:NVIC.USART2_LPUART2_IRQn=true\:0\:0\:false\:false\:true\:true\:true\:true 93:PD3.Signal=USART2_CTS 96:PD4.Signal=USART2_RTS 98:PD5.GPIO_Label=USART2_TX [STLK_TX] 101:PD5.Signal=USART2_TX 103:PD6.GPIO_Label=USART2_RX [STLK_RX] 106:PD6.Signal=USART2_RX 149:ProjectManager.functionlistsort=1-SystemClock_Config-RCC-false-HAL-false,2-MX_GPIO_Init-GPIO-false-HAL-true,3-MX_DMA_Init-DMA-false-HAL-true,4-MX_USART2_UART_Init-USART2-false-HAL-true,5-MX_USART3_UART_Init-USART3-false-HAL-true 168:RCC.IPParameters=ADCFreq_Value,AHBFreq_Value,APBFreq_Value,APBTimFreq_Value,CECFreq_Value,Cortex

Dear Sirs,We use ST25R3916 for our reader and  want to adjust  output power (0x28). We use RFAL library, could you tell me how to change the antenna driver output register (0x28)with the RFAL library, which function or variable should be used for the adjustment? best regardsDai Sai

I'm testing out using an SD card on the STM32U575I-EV. The example project I'm using is from the STM32CubeU5 MCU package (Projects\STM32U575I-EV\Applications\FileX\Fx_uSD_File_Edit).I'm able to insert an SDHC (32GB; FAT32 format) card, see the green LED blink (indicating successful read/write), disconnect the card, reconnect to my Windows 10 device, and see the "STM32.TXT" file.But when I want to try changing the format of the card to exFAT, it doesn't work anymore. I tried that same SDHC and also an SDXC that I had in the office, and both had the same issue. I ran the debugger on the project for both cards, and both return FX_BOOT_ERROR after calling fx_media_open().Is exFAT supported by FileX? I did some light research but haven't found anything saying it isn't possible. If it is supported, could I get some help with figuring out why it's not working for my setup?

Hi All - Not sure if this is the right place to ask this, but thought I would try anyway.I just finished a project that used Avalonia UI (C# based cross platform system for application GUIs) on a raspberry-pi 4 with a Waveshare touch screen attached.  It worked very well. :)  It now looks like I'll be starting on another project that needs a UI too but runs on an STM32 MCU based system.  Has anyone tried Avalonia UI on their system?  Did it even work?Curious if there are others who have done this before I start down this path.Thanks!

I am almost running out of limitations in my STM32L0 MCU as flash is divided into three sections.bootloader+user application+ota firmware. I have implemented a successful OTA at the moment. I am verifying the size of the OTA but I need to know if there is a quick and easy method to verify the OTA firmware before replacing the user application with it. Thank you.

I encountered a problem while desperately trying to make USB OTG_HS Host configured on a new Nucleo-U5A5ZJ-Q using CubeMX and ThreadX+USBX. I know that this board is not designed to provide USB power, but this can be overcome with undocumented SB8-10 jumpers and UCPD is not an issue here. I am also aware that at the beginning of the HAL_HCD_MspInit() function __HAL_RCC_SYSCFG_CLK_ENABLE(); line needs to be added.After several evenings of research (see here) I think I nailed down the problem to USB_HostInit() function.At the end of this function, host mode events are enabled using GINTMSK register (RM0456, section 73.14.8 OTG interrupt mask register [alternate] (OTG_GINTMSK), offset 0x18).  USBx->GINTMSK |= (USB_OTG_GINTMSK_PRTIM | USB_OTG_GINTMSK_HCIM | \ USB_OTG_GINTMSK_SOFM | USB_OTG_GINTSTS_DISCINT | \ USB_OTG_GINTMSK_PXFRM_IISOOXFRM | USB_OTG_GINTMSK_WUIM);  The problem I found and cannot explain is that after when this line is exec

HelloI'm using NUCLEO-H503 to make an I3C master, and I have some issues.1. I sent the ENTDAA command for I3C communication, but it does not go to HAL_I3C_STATE_READY.The code written after several attempts is as follows.HAL_I3C_Ctrl_DynAddrAssign(&hi3c1, &payload, I3C_RSTDAA_THEN_ENTDAA, timeout);HAL_I3C_Ctrl_SetDynAddr(&hi3c1, DynAddr);hi3c1.State = HAL_I3C_STATE_READY;Is this a normal way to use the Library?2. Please tell me how to read and write data on I3C slab.For I2C, HAL_I2C_Master_Transmit and HAL_I2C_Master_Receive were used to communicate with the slave device.Is there a function like this for I3C?The function I found is HAL_I3C_Ctrl_Transmit, but do not work in my board.Please let me know the functions you use for I3C communication and if you have a suitable example.I am sorry for my poor English.

Hi,  Can anyone help me identify the component(s)?  What kind of components these and what is the type of package (SSOP8 or TSSOP8)? Please see the the pictures. Thank you.

Dear Experts,I'm currently working on a project involving an STM32 board (B-U585I-IOT02A). I would like to use this board as a TCP Server. Therefore, from the STM32CUBEIDE application, I had observed that there is an example project in which it is possible to render this board as a TCP Server (Nx_TCP_Echo_Server). However, my problem was that it only returns the value returned by the TCP Client. So, I wanted to modify this program so as to be able to retrieve the temperature parameters. So, I created a program based on an example (https://wiki.st.com/stm32mcu/wiki/STM32StepByStep:Step4_Sensors_usage). I wanted to combine these two programs to retrieve the temperature data.To sum up, the diagram is as follows:Unfortunately, I've encountered errors in the program's implementation. It gives me the following errors:The project architecture is as follows: What I've noticed is that when I access the function where the error occurs (e.g. HAL_I2C_GetState), I'm able to access the .c file,

Hello,I am working on a project that uses a STM32H7B3I-DK Board and an octospi memory MX25LM51245G. I also use the touchgfx library for the graphical interface.I encountered a hard fault issue that occurs randomly during the initialization of touchgfx. Specifically, the fault occurs in the function Texts::setLanguage(0); which is called by the function touchgfx_init();.I used the cube programmer to analyze the fault and I got the following information (See Image)Could the problem be related to the access to the texts table, which is stored in the octospi memory. I wonder if there is a problem with the configuration or the timing of the octospi interface.I also noticed that before I increased the frequency of the octospi, I had another issue where the octospi got stuck in an infinite loop in the HAL_Delay function. I don’t know if this is related to the hard fault issue or not.I have attached some screenshots of the cube programmer interface showing the hard fault addresses and the octo

Hi there,debugging serial demo for SPC582B I was hoping to observe internal LINFLEX_D1 registers for future use during application debug.An ST employee helped me setting up the launch configuration, especially setting:SVD Path: C:\SPC5Studio-6.0\openocd\svd\spc58\SPC582Bx.svd During debug, all the peripherals are shown (inside the view 'Peripheral'). In the viw 'Memory', I can see the registers listed but their runtime values seem all 0s. If I add the same register as a watch expression, the actual value is 0x8184 (and it makes sense). Could the SVD file be broken or is it something else? Thanks for the support,FP

I'm sure I'm missing something here but for the life of me I can't see it.TIM2 CH1+CH2 are in use as encoder inputs but I believe I should still be able to generate a basic PWM output on CH3 at the same time?Code is all generated by Cube IDE and it reports no problems, I'm using the LL libraries rather than the HAL, this is the generated initialisation code in tim.c:  /* TIM2 init function */ void MX_TIM2_Init(void) { /* USER CODE BEGIN TIM2_Init 0 */ /* * TIM2 is Encoder 2 + PWM output 2 */ /* USER CODE END TIM2_Init 0 */ LL_TIM_InitTypeDef TIM_InitStruct = {0}; LL_TIM_OC_InitTypeDef TIM_OC_InitStruct = {0}; LL_GPIO_InitTypeDef GPIO_InitStruct = {0}; /* Peripheral clock enable */ LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_TIM2); LL_IOP_GRP1_EnableClock(LL_IOP_GRP1_PERIPH_GPIOA); LL_IOP_GRP1_EnableClock(LL_IOP_GRP1_PERIPH_GPIOB); /**TIM2 GPIO Configuration PA15 ------> TIM2_CH1 PB3 ------> TIM2_CH2 */ GPIO_InitStruct.Pin = ENC2_As_Pin; GPIO_

I want to connect B-CAMS-OMV (cam module ) to B-U585-IOT02A ( discovery kit). But there is no info bout that connection. I already read the user guide bout both. Can you give me some information or solution bout Connection with B-CAMS-OMV and B-U585-IOT02A ?

Hello, What is the maximum data transfer rate over the SPI interface for the LIS2DH12 accelometer? The datasheet doesn't say anything about this. About the I2C interface it is said that it can operate in standard mode (up to 100 kHz) and fast mode (up to 400 kHz). But nothing is said about the SPI interface.

I'm trying, unsuccessfully, to get a simplest single-channel single-ended polling-the-ADC example going on the nucleo h723 eval board.At first I started bare-metal in assembler from the datasheet, but couldn't get the second ADC sample to fire no matter what register gymnastics I did (the first ADSTART puts some bits in the DR, I figure that did something to the analog input).Then, figuring I'm still not setting up clocks right or something, I reverted to STM32CubeIDE and followed various HAL tutorials such as this one; same outcome.https://www.youtube.com/watch?v=6uiO68pdjZAThis particular ADC seems more involved than the simple ones usually covered in tutorials. Can anyone point me to an example of repeated single-shot acquisition with polling or interrupts that actually works on the 723ZGT6 part?(Bonus points if it can actually run at the claimed 3.5 MS/s...)

Hello everyone, I hope you are well.I'm working with the STM32WB55. I'm having difficulty getting RTC to work correctly.The VBat is always powered by 3v3, I have an on/off switch that only removes the power from the VDD, however, when I turn it off and on the microcontroller is stuck in the routine: "while (LL_RCC_LSE_IsReady() == 0U)". I noticed that when CFG_HW_RESET_BY_FW is 1, the board continues to function, but it resets the RTC registers and the time is lost and when CFG_HW_RESET_BY_FW = 0, the firmware is stuck in the "while (LL_RCC_LSE_IsReady() == 0U)" routine. Looking through the oscilloscope, the clock is all right.Can anyone help me? Thank you very much!

In the STM32H7 ref manual (RM0433 - Section 51.4.4), the following is said about configuring an SAI block in synchronous mode with the other SAI block in the same SAI peripheralI'm confused about the following statements:Typically, the audio block in synchronous mode can be used to configure the SAI in full duplex modeWhat is meant by full duplex mode above?One of the two audio blocks can be configured as a master and the other as slaveORBoth as slaves with one asynchronous block (corresponding SYNCEN[1:0] bits set to 00 in SAI_xCR1)and one synchronous block (corresponding SYNCEN[1:0] bits set to 01 in the SAI_xCR1).Option A makes sense to me, but for option B, is it valid for a slave block to be Asynchronous ?My SAI implementation on STM32H753 is configured as follows, is this a valid synchronization setup?SAI2-A : Master transmitter, asynchronousSAI2-B : Slave receiver, synchronous with SAI2-ASAI3-A : Slave transmitter, synchronous with SAI2SAI3-B : Slave receiver, synchronous with S

Hi,I am using IMU sensor LSM6DSO set to 100 Hz sampling rate. I am trying to figure out what is the tolerance of the IMU sampling frequency set by it's internal clock. How confident can I be that when I set it to 100 Hz, it will not fluctuate to higher/lower frequencies?

The "Copy to Clipboard" button is good to have, I guess, but in its current implementation you can't see what code is behind the button. Make it smaller, make it stay in the same position on a scroll, or something else so text can be seen. In contrast, the View More button is a great addition. More good features like that please.

To Andrew, SofLi Hy Andrew and SofLi. I well received your last informations posted this week-end. Therefore it was week-end. I test a NUCLEO board without ST-link; my computer is a Mac-mini and the NUCLEO board offers capabilities to be separate in to part, the ST-link microcontroller and the targeted microcontroller, enabling to reduce power consumption on plant. Bootloader offer capability to read and write any address in address space; then I think the simply way to give you understable informations it's to give you an excell file with the list of my search. Hoping this is nice to you, I hope an answer. Best regards. Butterfly.