Solved

Hi,I am using a EVSPIN32G02Q1S1 with LIN motor (BL23E33-01D-04RO) running in sensor-less only with 6-step moving 1 time with 1 turn and stops. I cannot connect Motor Pilot to the board for some reason (using the boards built in USART output to a RS232/TTL converter).I have tried this before with a EVPSPIN32F0601S1 and the LIN motor running at 50VDC and reset the motor parameter from 24VDC to 50VDC to match the minimum of the Inverter board both sensor, sensor-less and FOC and 6 Step with the same result but using the Motor Pilot, it kept coming back with Over Current no matter what I changed. My supply is 50VDC and runs up to 7 amps, and the current monitor I have connected in line says I am only pulling 0.5 amps when the over current occurs.So, my question is this.Does the Motor Work Bench change the parameters of the system settings to match the inverter and motor pair or is that up to me to do?Any help on this would be great. Thanks in advance.Charles 

* board - STM32N6570-DK*  using STM Cube 1.19.0* firmware v1.2.0Test projects* USBPD_SNK/USBPD_SRC So i'm trying to do PD with the STM32N6, but i can't seem to be able to test the example code from ST.  When i run USBPD_SNK, it just doesn't seem to work.  I get a weird no source available issue.  I thought it was because of ThreadX, but i tried VENC_USB and that example worked fine.  The USBPD_SRC also fails to work.  I don't know if this a STMCubeIDE problem or something weird with the specific PD usb examples.  

Hi i am working on a project with STM32H7A3VGT6 chipset which has LTDC controller. my goal is to make a LVGL based UI with SquareLine Studio and interface a 24 bit parallel RGB display with it . so i have made a UI using SquareLine Studio and imported to my project but the issue is when i try to build it it says flash overflowed. i know that the UI takes so much space but the spec of STM32H7.. says it mas  1 MB RAM . later in the linker script i saw it uses dual bank flash not single , so can i use it like this to make it work ? and any one can explain why is the RAM is also divided? MEMORY { ITCMRAM (xrw) : ORIGIN = 0x00000000, LENGTH = 64K FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 1024K /*FLASH2 (rx) : ORIGIN = 0x08100000, LENGTH = 512K*/ DTCMRAM1 (xrw) : ORIGIN = 0x20000000, LENGTH = 64K DTCMRAM2 (xrw) : ORIGIN = 0x20010000, LENGTH = 64K RAM (xrw) : ORIGIN = 0x24000000, LENGTH = 1024K RAM_CD (xrw) : ORIGIN = 0x30000000, LENGTH = 128K RAM_SRD (xrw) : ORIGIN = 0x3

Hi,Is there a way to enable weights compression while also using the STM32N6 NPU ?I saw there is Decompression unit in the reference manual where it tells the NPU compiler is the tool that generate codebooks offline (there is also mention of it in lib_aton.h too):This would help to reduce the model size in RAM. I've tried with models using a single channel in 1x1 Conv, but maybe this feature can only be used with some specific conditions ? Thanks!Alexis Murzeau  

I can't read référence; I am asking if this component is a zener Diode? And I'm looking for any équivalence  

Post edited by ST moderator to be inline with the community rules for the code sharing. In next time please use </> button to paste your code. Please read this post: How to insert source code.Hi,I am new to STM32 and I have to do a data acquisition board project using the STM32H7 MCU.I have the STM32H753XI-EVAL evaluation kit and I am trying out all the features one by one.I'm currently working on the DAC, which I have configured on CHANNEL2 on PA5. I am trying to start it up, send it a value, and then get its value to check and measure it using a voltmeter on PA5 of CN6 on the evaluation board.DAC1_Init :  static void MX_DAC1_Init(void) { /* USER CODE BEGIN DAC1_Init 0 */ /* USER CODE END DAC1_Init 0 */ DAC_ChannelConfTypeDef sConfig = {0}; /* USER CODE BEGIN DAC1_Init 1 */ /* USER CODE END DAC1_Init 1 */ /** DAC Initialization */ hdac1.Instance = DAC1; if (HAL_DAC_Init(&hdac1) != HAL_OK) { Error_Handler(); } /** DAC channel OUT2 config

Hello. I'm trying to configure the otm8009a 800x480 display panel from the stm32mp157f-dk2 dev kit on the Seeed Studio's stm32mp157c-odyssey board.The issue is that by probing display with modetest -M stm I'm getting:failed to open device 'stm': No such file or directoryBut with modetest -M simpledrm I'm getting this output:Encoders: id crtc type possible crtcs possible clones 34 0 none 0x00000001 0x00000001 Connectors: id encoder status name size (mm) modes encoders 35 0 connected Unknown-1 127x211 1 34 modes: index name refresh (Hz) hdisp hss hse htot vdisp vss vse vtot #0 480x800 60.00 480 480 480 480 800 800 800 800 23040 flags: ; type: preferred, driver props: 1 EDID: flags: immutable blob blobs: value: 2 DPMS: flags: enum enums: On=0 Standby=1 Suspend=2 Off=3 value: 3 5 link-status: flags: enum enums: Good=0 Bad=1 value: 0 6 non-desktop: flags: immutable range values: 0 1 value: 0 4 TILE: flags: immutable blob blobs: value: CRT

Hello,I am working with an STM32WBA65RI that is on our custom board, and working to reduce our power usage. Along this journey I found the issue with the HAL_PCD_MspInit() / DeInit() where the logic for the RCC PWR was inverted, which was another post I made.On our current hardware, I am noticing a large jump in current draw at the function call for __HAL_RCC_USB_OTG_HS_PHY_CLK_ENABLE() in HAL_PCD_MspInit().Just prior to the function call, the board is drawing 7.5mA, and immediately following the call it is drawing 33.09mA.I also tested this against the NUCLEO-WBA65 board, measuring across JP2, and see a jump from 3.05mA to 11.99mA, which seems more reasonable, albeit still quite large (according to DS14736, the max power draw from the OTG_HS PHY should be 5.7mA):For reference, our board has the following power setup:VBAT is 3.9 (for this test I am using a power supply). This feeds a PMIC (MAX77658). The PMIC takes the 3.9V in and creates a 3.3V using an internal switching regulat

Hey there,Is there an option to turn off the prompts after programming in the STM32CubeProgrammer?The Log output is enough for me:Not really a problem, more like a QoL thingy - but i didn't see an option anywhere.Would be a nice addition if it's currently not present. Like "only prompt on errors"

Dear ST Support Team,I would like to ask about the compatibility of using the X-NUCLEO-67W1M1 expansion board based on ST67W611M1 with the NUCLEO-F446RE development board.I had read the **X-CUBE-ST67W61 Data brief document on page 3**  "The X-CUBE-ST67W61 Expansion Package runs on STM32 32-bit microcontrollers based on• The Arm® Cortex®‑M33 and Cortex®‑M55 processors with Arm® TrustZone®• The Arm® Cortex®‑M7 processor"So, my questions are:1. Is the X-NUCLEO-67W61M1 hardware compatible with NUCLEO-F44 (Cortex M4 processor)? 2. Can I use raw SPI + AT commands without X-CUBE-ST67W61?, Has anyone done this on F44(Cortex M4 processor)? 3. Any known working example or GitHub project for (Cortex M4 processor)+ X-NUCLEO-67W61M1?

Hello all,I’m hitting a USB edge case on an STM32H573 in the 68-pin package (no VBUS sense pin, no VDDUSB domain).My setup (works fine in application):The product is self-powered (3V3 is always on). Because the package has no VBUS_SNS, I detect bus presence with a VBUS → resistor divider → buffer → GPIO (interrupt). My firmware only enables the USB device and D+ pull-up when this GPIO says VBUS is present, so we don’t “attach” or back-power a sleeping PC. That part is solid.The problem (ROM bootloader only):When I enter the System Memory bootloader and select USB DFU, the ROM seems to bring up the USB device and assert the D+ pull-up even if VBUS is absent (e.g., cable plugged into a powered-off PC or an unpowered hub). That effectively signals attach and can source current toward the host through D+/ESD paths—i.e., not USB-compliant for a self-powered device.Easy repro:H573 68-pin board, self-powered 3V3.Ensure no VBUS (PC off / hub unpowered).Boot to System Memory → USB DFU.D+ goes h

Continually get the error when I start prerelease 3.4.11  I am on a A Windows 10 PCAn error occurred while installing STM32Cube bundles: [adoptium-jre@>=17.0.14+7.st.6]. Some feature may not work as expected. Please check output channel logs.

Hi All, I've been using the VL53L1 sensor for drone height control, and the results have been quite good- however, the environment it is used in has plastic skylights with poor IR blocking. This causes unstable readings in direct sunlight. Some of the IR is blocked, and as such this is tolerable but undesirable. Would changing to the VL53L4CX improve this? Ranging up to 3m is required. Will the L4CX broadly outperform the L1CD in most situations?   Thanks!

 Hello,Requesting marking ID confirmation "456RQ-K317" for St. Micro MPN: M24256-DRDW3TP/K. 

Hi!It might be a *** beginners question but I'm quite lost...I'm trying to deploy my .ONNX model on my new NUCLEO-N657X0-Q board. The MCU on it STM32N657X0H3Q, seems to have 4Mb of RAM and no flash, but the board itself has 512Mb octaflash memory on it. My model is calculated as 2.71 MB of flash memory and 402 Kb of RAM. The ST edge developer tool claims that my board doesn't have enough resources and it won't create a suitable STM project for the IDE.My question is - is there a way to work with the board on AI models? is it a bug in the software or am I doing something wrong?Thank you!Amir

 Hello,I am using STM32CubeIDE with the STM32F429I-Discovery board,and my goal is to connect it with the MT9M001 camera module.As a first step toward that, I would like to make the LCD display work properly.In the STM32Cube_FW_F4_V1.28.0 package,there are many sample projects organized as follows:  Projects > STM32F429I-Discovery > Examples > LTDC > LTDC_Display_2Layers If I import this Example project into STM32CubeIDE,will the LCD automatically display the sample image?Or do I need to perform some additional setup or configuration steps?I would appreciate any advice or guidance.

I want to develop a simple project in CubeIDE to send "Hello" or something similar from STM32F746G-Disco through a UART port with Realterm (or similar app) running on my laptop. I have a  USB-to-TTL adapter from Waveshare. Can someone help me?

When I use SPC5 Flash Programmer V2.8.1 to connect to the SPC56 CAN programmer, after configuring all the settings and clicking the connect button, the SPC5 Flash Programmer remains in a busy state and fails to establish a normal connection. Could you please tell me how to solve this problem?  Note: The operating system of my computer is Windows 10 64-bit. Besides, when I check the SPC5 Flash Programmer installation Details, it shows that the flash tool plug ins of STMicroelectronics are unsigned, Is this the reason why it cannot work properly? 

Hi ST Community,    Our project uses STM32H743 (LQFP100). The system clock is set at the max 480MHz. The USB Device interrupts would occasionally cause a HardFault. For example, if we plug in or unplug the USB. The data hpcd would occasionally be 0xFFFFFFFF. Sometimes it's the hpcd->pClass[0] We have enough size for the stack and heap. A "workaround" is to lower the system clock to 240MHz...   What we don't understand is that the USB clock source is from the "RC48" 48MHz clock, independent from the system clock, which sources the HSE. How does lowering the system clock help resolve this issue? We also tried using HSE to generate the 48MHz for the USB, but the USB just doesn't run. Is there other settings or configurations that we might have set incorrectly?   Another thing to mention is that we have a conflict with the RCC CRS SYNC.                    Attached is our clock configuration and .ioc file for your ref

Hi all,I’m working with a new ST67W611M1A6BTR Wi-Fi module on a customized STM32H745 board.I followed the official X-NUCLEO-67W61M1 and NUCLEO-U575ZI-Q passthrough example, and I am able to communicate with the module (UART passthrough to PC works, and I can get to the command prompt on the NCP using the qcc74x shell).However, when I try to flash new NCP firmware using QConn_Flash, the process fails at the “handshake” stage. I'm wondering if I can use the same procedure for the standalone module? Any help is appreciated! Many thanks!My setup:Hardware: ST67W611M1A6BTR module on custom board, UART connected to STM32H745.UART passthrough: Confirmed working; I can get the NCP shell prompt (see below for log).Flashing method: Following the procedure in the ST documentation (same as for X-NUCLEO/NUCLEO board), trying to use QConn_Flash tool in standalone mode.Logs:Build:12:05:38,Oct 242024ersion of use omponents:Version: component_version_btblecontroller_1.6.50Version: coponent_version_

Hello, my project is using all 4 SPI interfaces on the STM32G474. SPI1-3 all work flawlessly, but SPI4 never triggers the RXNE flag. All SPI buses are configured identically, with the only differences being the pinouts and APB1 vs 2 bus. I am polling the transactions directly.Initialization:if (hspi_.Instance == SPI1) LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_SPI1); else if (hspi_.Instance == SPI2) LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_SPI2); else if (hspi_.Instance == SPI3) LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_SPI3); else if (hspi_.Instance == SPI4) LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_SPI4); LL_SPI_SetMode(hspi_.Instance, LL_SPI_MODE_MASTER); LL_SPI_SetTransferDirection(hspi_.Instance, LL_SPI_FULL_DUPLEX); LL_SPI_SetDataWidth(hspi_.Instance, LL_SPI_DATAWIDTH_8BIT); LL_SPI_SetClockPolarity(hspi_.Instance, LL_SPI_POLARITY_LOW); LL_SPI_SetClockPhase(hspi_.Instance, LL_SPI_PHASE_1EDGE); LL_SPI_SetBaudRatePrescaler(hspi_.Instance, LL_SPI_BAUDRATEPRESCALE

Hello guys,Can anyone help me on how i need to set up a dma chain reaction so i can read from a timer ccr1, ccr2 registers and write their values to hrtim period and compare1 registers? The only thing I have found until now is how to set up the dma for the timers while being on PWM Input mode, burst read the cc1, cc2 registers and store their values to memory. I have read that I need to use then a DMAMUX request to generate an DMA request for the HRTIM to read the memory and then apply the changes to the peripheral, but I still don't understand how I should i configure the board. I'm using an STM32G474RET.Thanks for your time in advance.

Hi, I was trying to upgrade my ble wireless stack from CubeProgrammer but everything give me this error. I tried to install stm32wb5x_FUS_fw or stm32wb5x_FUS_fw_for_fus_0_5_3 to their correct addresses from release notes but nothing works. I am able to flash code from cube ide but these wont work. I can start FUS or take BOOT0 to 1 but these did not work too.  Only thing I have in my mind is maybe my cube programmer. Due to language settings my cube programmer installation step 8 is stuck(I read this error from the forum too) but I can access to cube programmer from program files and it can connect/read/flash so I dont think this is the problem too.  On the board RX/TX pins between st link and mcu are not connected but it should not be the problem as well because I am using st link and can flash anything from cube ide  

I am currently working on a project that uses the STM32U575CGU3 microcontroller. The goal of the project is to display pressure and temperature values over CAN J1939 and CANopen communication protocols in a digital output format. For sensor data acquisition, I am using an external two-channel ADC to measure pressure and temperature values. Regarding the system clock, I have tested the application using both the internal clock source and an external crystal oscillator. The system performs well in both configurations. However, I would like to request your expert guidance on the recommended clock source for this application. Specifically: Is it advisable to use the external crystal for better timing accuracy and long-term stability? Or is the internal clock sufficiently reliable for CAN J1939 and CANopen communication in a production environment?

Hello,I want to interface two SAI of STM32L4S7VIT6 with two SGTL5000, which are working as transmitter and receiver at any time as used in telephone. Also interface one Si32287 through PCM. In datasheet SAI1_D1,D2, D3 are given but in reference manual it is not given. Also can we connect for one SGTL5000 with SAI1_FS_A, SAI1_MCLK_A,SAI1_SCK_A,SAI1_SD_A and SAI1_SD_B of same SAI1. And for other SGTL5000, can we connect SAI1_FS_B, SAI1_MCLK_B,SAI1_SCK_B of same SAI1 and for data SDI1_D1 and SDI1_D2. What are the functions of the lines SAI1_D1 and SAI1_D2?