Solved

Posted on February 02, 2017 at 20:47Can anyone advise me if the STM32F0 or STM32L0 range supports a USB host or SD cards.In the Datasheets it refers to usb but I can't find something explicitly which says they support usb host.I want a controller where I can save data to an SD card or USB memory stick.Thanks

Posted on February 20, 2018 at 16:15HiI'm testing F767Zi-Nucleo to write some data to a 16G SD card with no file system.With HAL_SD_WriteBlocks function, everything works fine. I can read out the data that just have been wrote.With HAL_SD_WriteBlocks_DMA function, no error during excution.But I can only read out 0x00 in the data block that just been wrote before.SDMMC controller clock frequency is 4 MHz.SDMMC1 and SDMMC2 are tested and they both have this problem.Has anyone encountered same situation? Need help.Thanks a lot.

Posted on February 23, 2018 at 17:55Hi,      I tried to run the example on STM32F072-EVAL found in  STMicroelectronics\STM32Cube_FW_F0_V1.9.0\Projects\STM32072B_EVAL\Applications\USB_Device\CDC_Standalone.When I plug CN4 USB connector to my PC, I see a STMicroelectronics Virtual COM Port (COM3) appear but with an exclamation mark. I have the error code 'This device cannot start. (Code 10))My PC has Windows 10.1) I tried to reinstall the drivers (even if it is not necessary for Windows 10)2) I tried to increase the stack and the heap3) I tried to change my bDeviceClass and bDeviceSubClass to 2Unfortunately, I had no success with those modifications. Can somebody help me with that problem ?Vincent #stm32f072-eval-cdc

Posted on December 20, 2016 at 15:00I am porting older code to the HAL library using cubemx for an STM32F4_Discovery board.My application consists of a 'bootloader' that resides in the lower segment of flash.The actual application resides in higher segments.The bootloader can optionally flash those segments with new code and will then jump to that code.This code is regular code created via cubemx with a little different loader script to make the code reside higher in memory.So when the bootloader jumps to that code ALL initialization is done for the SECOND time, but now for the application in high memory. This used to work fine, but with the HAL library at least the Systick interrupt is NOT coming.So function HAL_Delay() is not working for example.I would have hoped that the HAL init code would work irrespective of the state of the processor, but alas...What I have tried is to execute some DeInit-functions before the jump, e.g.USBD_LL_DeInit(&hUsbDeviceFS);HAL_DeInit();jumptoapp()

Posted on May 06, 2017 at 00:19Hello,I have been trying to download the library for CLASSB certification for STM32's but i can't manage to download it.http://www.st.com/en/embedded-software/x-cube-classb.html I tried to press request software and fill the blanks but even tho i pressed the confirm request it won't progress. What should i do? I have to download the library for a university project.Thanks for help!!!

Posted on February 21, 2018 at 22:43Hello,We're using the LSM6DS33 accelerometer/gyrometer in a product, which is expected to be continuously manufactured for ~5 years. I'm slightly worried about its longevity. I know that nowadays it is listed as Active, and also that it is not in any longevity program.Is it expected to be classified as NRND soon? Can I use it in this application without worries or should I be prepared for future changes since the beginning?Thanks,

Posted on March 01, 2018 at 20:31Hi everybody,and greetings as this is my first post here Anyway, I am experimenting with my X-NUCLEO-IDS01A4 Spirit1 expansion board on a NUCLEO-STM32L476RG board. I'd like to write my own SPIRIT1 driver and I'm using the Low Layer library from the STM32CUBE library, no IDE just Sublime and my Makefile and JLINK to debug.So far I can read and write the SPIRIT1 registers and now I'd like to configure the registers. I've downloaded the SPIRIT1 DK App and I generated a configuration code (868 MHz, data rate 38.4 kbps) containing 2 functions: SpiritBaseConfiguration and SpiritVcoCalibration. The former executes flawlessly, however, the execution stucks in the latter function, here:SpiritSpiCommandStrobes(COMMAND_LOCKTX);do{SpiritSpiReadRegisters(0xC1, 1, &state);}while((state&0xFE) != 0x1E); /* wait until LOCK (MC_STATE = 0x0F <<1) */SpiritSpiReadRegisters(0xE5, 1, &cal_words[0]); /* calib out word for TX */Between the 2 functions I calle

Posted on March 01, 2018 at 11:09Hello,The second and fourth lower lines in Table 85 both state THD , single ended with BOOST=1, however with different resulting values. Probably the second lowerst line should be THD, Differential, BOOST=1.Bye

Posted on December 18, 2017 at 16:54Hi!The LL library causes a compiler warning (dereferencing type-punned pointer; see below).Can I ignore this warning?-Thomas/STM32Cube_FW_F3_V1.9.0/Drivers/STM32F3xx_HAL_Driver/Inc/stm32f3xx_ll_crc.h:355:3: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]__STATIC_INLINE void LL_CRC_FeedData16(CRC_TypeDef *CRCx, uint16_t InData){ *(uint16_t __IO *)(&CRCx->DR) = (uint16_t) InData;}

Posted on February 22, 2018 at 15:04Hi,In-fact I tried asking query through service request. The website portal seems to be very slow. I am not sure whether it got submitted or not.So I am asking the query directly to you here. Please help me in addressing this query :Hi, We are using STM32H753xI in our design and we would like to use OTG_HS interface.Our plan is to connect the OTG_HS signals (DP, DM, VBUS, ID) to micro USB connector.The query is CAN WE CONNECT KEYBOARD AND MOUSE to the OTG_HS interface? We may run OS in microcontroller and we will view it through LCD interface. By connecting Keyboard/mouse we want to give inputs to OS. Is it possible to achieve this requirement using OTG_HS interface?Hope I made my query clear to you. Please respond ASAP.Regards,Vijetha

Posted on February 26, 2018 at 04:19Environment:Windows10 (x64)Matlab R2017aSTM32-MAT/TARGET-v4.4.2STM32CubeMX-v4.24.0STM32Cube MCU Package for STM32F0 Series -v1.9.0SW4STM32-v2.4TrueSTUDIO-v9.0.0The STM32F030CC has 6 USARTs. USART1 and USART2 have separate interrupts. USART from 3 to 6 have one common interrupt. Apparently, STM32-MAT/TARGET searches for individual interrupts for each USART, because the code generated for USART1 and USART2 works correctly (via interrupts), but for USART3-USART6, STM32-MAT/TARGET generates the code as if they were working without interrupts, in polling mode (HAL_UART_Receive function). At the same time, the interrupt handler for USART3_6 is generated by the ''Cube'', but is not used during operation. It turns out completely incorrect work of the code.That is, STM32-MAT/TARGET does not accept USART with common interrupts as working on interrupts. This is even seen in the Simulink USART blocks - Interrupt checkbox is unfilled for USART3 - USART6.Here we

Posted on February 26, 2018 at 16:16Hello,could anyone tell me in which format (or which SW) could i see brd file in schematic pack for this board? It is sooo annoying to search it every time they make a new board.Many thanks#stm32h753i-eval

Posted on February 25, 2018 at 21:55Hii do have the B-L072Z-LRWAN1 board and try to make a End-node..When i want to debug the Stm-cube LRWAN END NODE exsample it gives me a failure ...the port is in use ?What can i do wrong ...Normally absolut no problems...Both Keil and openstm32 make the failure..Anyone know ?Hjalmar

Posted on February 26, 2018 at 17:34I'm measuring the current on JP6 (IDD) and I see 4mA at the lowest when running the Power_Management sample or even holding the MCU in reset. I am powering the board via the USB connector. Is this incorrect?I've tried using SLEEP_MODE, STANDBY_MODE, and STOP_MODE defined, and they all show around 4mANucleo-F411RE

Posted on February 23, 2018 at 07:04 Hello, I have developed a IAP application based on STM32F030CCT6. The application code is received on UART and I can store it in flash, I am storing codeat 0x08010000. But I am facing problems in executing it. While trying to jump at code my code goes into HardFault interrupt. And unfortunately on this MCU there is no implementation of HFSR and VTOR. Hence I am not getting the reason for hardfault! I am using below code for jumping. And I have also remapped the Vector table in application binary. I am using Keil MDK5 and hence I have verified the addresses of code from MAP file. The application code's RESET starts at 0x08010000. and the IAP starts at0x08000000 as expected. Please guide me. typedef void (*jumpFunction) (void);//typedef for function pointer jumpFunction JumpToFunction; //Function pointer uint32_t JumpAddress,somaddr;//Address of function pointer __disable_irq(); JumpAddress = *(__IO uint32_t*)(FLASH_X_START_ADDR + 4); JumpToFunc

Posted on February 24, 2018 at 12:24Hi,Why is CubeMX not generating the syscall.c file?RegardsRamazan#syscalls.c

Posted on February 21, 2018 at 18:04How to remove totally the Virtual COM driver for STM32?The STlink is working but the virtual com doesn-t work and windows 10 can not find driver to the board.Since the driver is delivered in a .EXE format I can not indicate windows where the driver is and re-installing the driver or try to auto search doesn't solve the problem.On the other hand the board is working in another windows machine.

Posted on February 22, 2018 at 18:52What is the register address of APB1ENR and APB2ENR?Where can I find it in Nucleo STM32F103RB Reference Manual?#apb1periphclock #apb2 #stm32f103xx

Posted on January 19, 2017 at 15:15I need to read the unique device ID from a STM32L0.The Low Level hal driver source (stm32l0xx_ll_utils.h, V1.7.0, 31-May-2016) uses:__STATIC_INLINE uint32_t LL_GetUID_Word0(void){ return (uint32_t)(READ_REG(*((uint32_t *)UID_BASE_ADDRESS)));}__STATIC_INLINE uint32_t LL_GetUID_Word1(void){ return (uint32_t)(READ_REG(*((uint32_t *)(UID_BASE_ADDRESS + 4U))));}__STATIC_INLINE uint32_t LL_GetUID_Word2(void){ return (uint32_t)(READ_REG(*((uint32_t *)(UID_BASE_ADDRESS + 8U))));}The reference manual says:Base address: 0x1FF8 0050Address offset: 0x00 => Bits 31:0Address offset: 0x04 => Bits 63:32Address offset: 0x14 => Bits 95:64#uid #unique-id #unique-device-id-register""

Posted on September 13, 2016 at 01:03Everything in the code seems to be working properly in Debug Mode. As soon as a keyboard is plugged into the USB-OTG port on the board,  the USB-Debug log shows the MIDI class is started, the Init routines run, the endpoints are linked to MIDI In and MIDI Out, and MIDI Process seems to be armed and ready to accept MIDI input from the keyboard.However, when I play a note on the keyboard, I notice no data is being received. The MIDI core is idling, as if nothing is being output from the keyboard.Does anyone have any thoughts about what could be causing this? Thank you!!Christopher #usb #host #hal-usb-midi-host-f7-nucleo-144 #bulk-in #synth-usb-midi-nucleo-144

Posted on February 22, 2018 at 13:42Hello there,I am working on MSD Bootloader which I successfully Implemented  in STM32F207VETx. However while working I found that the default build expect 8.3 format file names, and not Long File Names (LFN).I tried using LFN by making following changes in ffconf.h&sharpdefine _CODE_PAGE 437&sharpdefine _USE_LFN 1    /* 0 to 3 */ / When enable the LFN feature, Unicode handling functions (option/unicode.c) must/ be added to the project.&sharpdefine _MAX_LFN 40    /* Maximum LFN length to handle (12 to 255) */&sharpdefine _LFN_UNICODE 0 /* 0:ANSI/OEM or 1:Unicode */&sharpdefine _STRF_ENCODE 0and getting the following error undefined reference to `ff_convert' which I think is a function in unicode.c So My question is where can I Find Unicode handling functions as i want to give a long name for my file#tilen-majerle #clive-one

Posted on February 16, 2018 at 22:35I just upgraded to CubeMx 4.24 and attempted to migrate a STM32F7 project .ioc file. The migration failed with a Java null pointer exception when it reached the CAN IP portion.To verify my .ioc file was not the culprit, I created a new project and the issue persisted. Here are the steps to reproduce: Start CubeMx 4.24, create new projectSelect STM32F745VET for processorSave project, Close CubeMxRe-Open CubeMx, attempt to open file previously created -- opens successfully.Add Ethernet IP, allow clock tab to auto-resolve clock tree issuesSave project, Close CubeMxRe-Open CubeMx, attempt to open file previously created -- throws null pointer exception and uses 100% CPUHere is the topmost portion of the stack trace when it throws the exception:2018-02-16 16:29:02,320 [INFO] UtilMem:68 - End LoadConfig() Used Memory: 2695795904 Bytes (3036151808)2018-02-16 16:29:02,386 [INFO] ThirdPartyDb:293 - Open Third Party DataBase File (/home/david/.stm32cubemx/plu

Posted on February 22, 2018 at 11:15hi everybody,i 'm setting the ADC on STM32L051x6.it works correctly but i have problem with conversion time. It is about 8us. To measure it i'm using a signal that is setted high at the start of conversion and low at the end of conversion.The start of conversion is triggered on a timer event and i useLL_GPIO_SetOutputPin(GPIOA, PA6); to set signal.I'm tryng to reduce this time. Can somebody help me?this is the setting code for ADCvoid LED_CURRENT_ADC_Init(void){LL_ADC_SetClock(ADC1, LL_ADC_CLOCK_SYNC_PCLK_DIV1); LL_ADC_SetSamplingTimeCommonChannels(ADC1, LL_ADC_SAMPLINGTIME_1CYCLE_5); LL_ADC_SetResolution(ADC1, LL_ADC_RESOLUTION_12B); LL_ADC_SetDataAlignment(ADC1, LL_ADC_DATA_ALIGN_RIGHT); LL_ADC_REG_SetSequencerChannels(ADC1, LL_ADC_CHANNEL_3); LL_ADC_REG_SetContinuousMode(ADC1, LL_ADC_REG_CONV_SINGLE);  LL_ADC_ClearFlag_ADRDY(ADC1); LL_ADC_EnableIT_EOC(ADC1); LL_ADC_Enable(ADC1);}this is the adc IRQvoid ADC1_COMP_IRQHandle

Posted on February 21, 2018 at 12:41Whenever we connect a DISCOVERY KIT to computer via USB, we see a drive by the same name as the controller. How is this achieved? Also, it allows drag and drop of .bin files for flash. How can this be achieved?

Posted on February 15, 2018 at 11:25Hi everyone,I'm tryng to use DMA with ADC on STM32L051x6 MCU.When i see the Memory dump at the memory address of variable i takes the correct value from ADC DR but DMAIrq doesn't work neverCan somebody help me?Thanks in advancebool LED_CURRENT_ADC_Init(void){    LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_DMA1); //Enable DMA Clock    DMA1_CSELR -> CSELR &= 0xFFFFFFF0; //Remap of DMA channels to ADC    LL_ADC_REG_SetDMATransfer(ADC1, LL_ADC_REG_DMA_TRANSFER_UNLIMITED); //Enable DMA    transfer on ADC    DMA1_Channel1 -> CPAR = (uint32_t) (&(ADC1->DR)); //Configure the ADC data register address    DMA1_Channel1->CMAR = (uint32_t)(ADC_val); //Configure the memory address    DMA1_Channel1->CNDTR = 1; //Configure the number of DMA tranfer to be performs on channel 1    LL_DMA_SetChannelPriorityLevel (DMA1, L