Solved

..

I've just upgraded to MX6.8.0 and IDE1.12.0. I get this notice when loading a new application or example program. It doesn't affect anything and choosing OK let's everything proceed, but I'd like to get rid of the notice and find out where it's getting the "../../../../.." path.Thanks,TJM

Hello,We are going to use LIS2DE12TR accelerometer, in our ultra low power device, to wake on motion. Here is schematic for LIS2DE12TR, Our requirement :1) ultra low power consumption2) Wake MCU on Motion by INT_1 Pin Below are queries regarding schematic:1) What should be value of R48 and R49.2) Is schematic is ok?Thank You

void capture(Adafruit_OV7670 *platform){ uint32_t i =platform->bufferSize; uint16_t *shot =platform->buffer; uint8_t* pclk = platform->pins.pclk.Read_reg; uint8_t* vsync = platform->pins.vsync.Read_reg; uint8_t alt = 0; while(alt==0){ alt=*vsync; }   //while(!OV7670_pin_read(platform->pins.hsync)); while(i-- >1){ shot[i]=0; uint8_t j = 16; alt=*pclk; while(alt==0){ alt=*pclk; } while(j-- > 9) shot[i]|= (OV7670_pin_read(platform->pins.data[j-8]))<<j; /*while(alt!=0){ alt=*pclk; }*/ while(alt==0){ alt=*pclk; } while(j-->1) shot[i]|= (OV7670_pin_read(platform->pins.data[j]))<<j; /*while(alt!=0){ alt=*pclk; }*/ } }"pins" is an array of Band pins, a strut defined in gpio.h. All the variables that assign their value to the variable "alt" map to the allias of bits of IDR registers. I am using nucleo-144 stm32f439zi. Everything is wired correctly and my main prob

Beside the MB1791 BOM doubt, there is PCB Layer Stack doubt too.About MB1791 PCB & Gerber Files, there is no Signal copper layout in the Middle Layer-1 (G1 Layer) & Middle Layer-2 (G2 Layer). Why the setting applied 4-layers PCB instead of 2-layers PCB ? Info referring --> STM32WL55CC - Sub-GHz Wireless Microcontrollers. Dual-core Arm Cortex-M4/M0+ @48 MHz with 256 Kbytes of Flash memory, 64 Kbytes of SRAM. LoRa, (G)FSK, (G)MSK, BPSK modulations. AES 256-bit. Multiprotocol System-on-Chip. - STMicroelectronicsPls advise.

Dear colleagues,I woild like to ask you help me with may issue below:Why do I lose data when writing flash memory and an error occurs my code in the attachment.Code seems good, but I am sure that I loose something.In memory loosed letters "llo" from "Hello".Thnak you.With Best regardsIvan

使用STM32F446RE的Tim encode模�?接�?�EC11编�?器数�?��?�以区分正�??转�?�？如何使用LL库实现？

hi all,I would like to experiment with the TFM applications contained in the STM32CubeU5 package on my B-U585I-IOT02A boardunfortunately, it seems that STM32CubeIDE is not supporteddoes anyone have suggestions on how to build the TFM applications, based on free and/or open software, without the need to install trial versions of EWARM?thanks in advanceGianluca

TN0018 calls out in the Process considerations section that the board must be properly cleaned after soldering if "self-cleaning" solder paste is not used. Are there any guidelines on cleaning methods that will not damage the sensor? Can the sensor port be covered with something like Kapton tape to protect it during the cleaning process?

..

I am using the B-U585I-IOT02A discovery kit with the STM32U585AI chip. Attempting to set the system clock value in STM Cube to anything that would result in voltage scaling above PWR_REGULATOR_VOLTAGE_SCALE4 results in a timeout and thus failure in the HAL_PWREx_ControlVoltageScaling() function.This is all in the Cube generated code, without any other additions or manipulation.Code sticks int he Error_Handler() function after the call to HAL_PWREx_ControlVoltageScaling().Edit: I cannot even manually manipulate the PWR registers via ST-LINK. I can do this on other development kits (STM32L5 for example)STM32CubeIDE Version: 1.12.0 Build: 14980_20230301_1550 (UTC)What is the problem here? I need to be able to set a clock speed as I like.void SystemClock_Config(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};   /** Configure the main internal regulator output voltage */ if (HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE2

I have a MEMS microphone (IM72D128V01, using this eval kit) with PDM output connected to a STM32U5 NUCLEO board.It's connected to the ADF/Audo Digital Filter peripheral which I have configured to provide a 5th order CIC filter with a 32x decimation factor. ADF clocking is configured to output a 3,072,000Hz data clock to the MEMS sensor. ​Every time I start my STM32 program I have to physically power cycle the MEMS IC or else I get a DC bias in the data register - the most significant byte of the 24bits in the data register (which includes the sign bit) is constantly 0x0 meaning the integer sample values are all positive.​As soon as I power cycle the MEMS IC I immediately start getting a mix of positive and negative integer sample values as I would expect. This persists until I terminate and relaunch in CubeIDE.​How do I diagnose/resolve this? ​

Details:MCU: STM32L4R9ZGJ6IDE: STM32CubeIDE v1.6.1SDK: STM32Cube_FW_L4_V1.14.0Board: Custom PCBHello,I am seeing really strange behavior where bits 31-24 in the RCC->CSR register are usually always 0. I have verified this behavior on two boards. The only bit I ever see set is PINRSTF but only after programming the board with the debugger attached. Subsequent resets with NVIC_SystemReset(), toggling NRST, watchdog reset, etc do not set the reset bits accordingly.I have tried reading the registers after basic system init and immediately upon entering main() with the same result. Below are two tests that read RCC->CSR just after calling NVIC_SystemReset().Test 1 (Read CSR after basic system init): Test 2 (Read CSR as soon as main() is entered): I can't figure out why this would be happening. I skimmed through the MCU erratas and didn't see anything, but I could have overlooked something.Thanks,Derek

im using pc8 as a reset pin and ive check it with a logic analyzer and wen its initalized it drops low then goes back to high before im calling my function to drop it low btw im using saleae logic 2 void reset_pin_init(void){ //PC8 RCC->AHB1ENR |= (1U<<2);   GPIOC->MODER &= ~(1U<<17); GPIOC->MODER |= (1U<<16);   GPIOC->OSPEEDR |= (1U<<17); GPIOC->OSPEEDR |= (1U<<16);   GPIOC->PUPDR &= ~(1U<<17); GPIOC->PUPDR |= (1U<<16);   GPIOC->ODR |= (1U<<8); }   void si47xx_reset(void){   reset_pin_init();   GPIOC->ODR &= ~(1U<<8); systickDelayMs(50); GPIOC->ODR |= (1U<<8); }

Hi, when I use VSCode STM32 extension, VSCode always show this error. Could you help me solve this problem?Thanks for your help!

I'm to using the IDE and attempted to edit my first main.c file...and the paste function doesnt work. CTLR V does nothing and the right click menu has it available but also does nothing.

Hi everyoneI'm a student and I'm totally new to stm32 controllersI spend two weeks trying connecting stm32l431rct6 to w5500 but I failedcan any one guide me to a tutorial or some videos that I can use ? or can anyone help methank you

..

Hi,I found this in datasheet But we config SDRAM at 120MHz, because we are running at 480MHz.(480MHz / 2 / 2 = 120MHz).I am thinking the datasheet is for STM32H7xx 400MHz, because when I config SDRAM at 120MHz, the system works fine without issue.Does max 100MHz FMC clock apply for STM32H7 480MHz?Thanks.

Hi Everybody,Firstly, I would like to note that I am pretty new to embedded systems, so I am sorry if my terminology is off or if I am not communicating clearly, please forgive the (probably) gaping holes in my knowledge. I will do my best to communicate my problem as clearly as I can. I am working with a STM32L412 on product development, the team I a part of would like to have a section of flash not be erased when the MCU is reprogrammed. The amount of information that we need to be preserved is small, maybe at most 200 bytes, enough space to store some information like a serial number, baud rate, etc.To that end, I currently have sectioned off the last page (page 63) of flash in my L412 in the linker file to separate it from the rest of flash, so I can use it to contain this information. //This is what I have so far in the linker file. RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 40K RAM2 (xrw) : ORIGIN = 0x10000000, LENGTH = 8K FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 126K Devic

�?��?空隙MX_SPI2_Init（空隙）#include "app_nfc7.h"/* Private includes ----------------------------------------------------------*//* USER CODE BEGIN Includes *//* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*//* USER CODE BEGIN PTD *//* USER CODE END PTD *//* Private define ------------------------------------------------------------*//* USER CODE BEGIN PD *//* USER CODE END PD *//* Private macro -------------------------------------------------------------*//* USER CODE BEGIN PM *//* 用户代�?结�?� 下�?� *//* Private variables ---------------------------------------------------------*/SPI_HandleTypeDef HSPI2;/* Private function prototypes -----------------------------------------------*/void SystemClock_Config(void);static void MX_GPIO_Init(void);static void MX_SPI2_Init(void);/* USER CODE BEGIN PFP *//* USER CODE END PFP *//* Private user code ---------------------------------------------------------*//* USER CODE BEGIN 0 *//* USER CODE

..

Hello,Using a custom board loosely based on STM32mp157F-DK2we are using boot0 and boot2 pins.According to documentation,boot mode configuration is as follows;Boot Mode     BOOT2  BOOT0Recov/DFU        0      0Nor              0      1Reserved(DEV)    1      0SD-Card           1      1 Whereas with our board,I get a table like this Boot Mode     BOOT2  BOOT0DFU              0      0DFU              0      1Reserved(DEV)   1  &n

I am not a programmer and beginner in Embedded software, I recieve a keil project from another person. I need to change some parameters in the project. I have STM32cube IDE with debugger. So how to open the keil project with its file to STM32cube IDE and create the project as STM32cube project and download to ucontroller?It would be nice each step explanation , screenshot if needed. Thank you