About Eleon BORLINI

Eleon BORLINI · 2022-11-18

The ISM330IS product embeds a general-purpose core, a new ST category of processing, called ISPU (intelligent sensor processing unit). The ISPU is based on STRED architecture, a proprietary architecture developed by STMicroelectronics. Its optimized ...

Eleon BORLINI · 2022-04-08

Save the date --- APRIL 28, 2022, SEMI HQThis class will explain and demonstrate how AI/ML logic can be implemented on Edge devices such as Smart sensors. Power efficiency, latency, and bandwidth considerations are important for AI/ML implementation ...

Eleon BORLINI · 2022-03-11

This article describes how to configure the Machine Learning Core (MLC) on IIS2ICLX to implement the detection of the tilt angle, i.e. the current inclination of the device, in the range of -20 to +20 degrees. The hardware used is the ProfiMEMS with ...

Eleon BORLINI · 2022-02-28

This article deals with the implementation of a simple machine learning case (the recognition of the state of an asset in movement) on the LSM6DSOX core of the SensorTile.box, combined with a finite state machine configuration that determines the fre...

Eleon BORLINI · 2022-02-09

This article deals with the implementation of a simple machine learning case (the recognition of the state of a door) on the LSM6DSOX core of the SensorTile.box, and the visualization of the output of the decision tree on the STBLE Sensor smartphone ...

Eleon BORLINI · 2024-02-19

Hi @Zhou JianQiang , LSM6DS3TR has "SH" marking, while LSM6DS3TR-C has "SE" one. Each product has its own code, so that you can recognize it univocally (but you should refer to the commercial product definitely). -Eleon

Eleon BORLINI · 2023-12-19

Hi @FKara.3 , For the speed calculation from acceleration data you can again use MotionSP library since the library only matters to have 3-axis acceleration data in input. About the pre-calibration, for the accelerometer-related part of the LSM6DSV...

Eleon BORLINI · 2023-08-18

Hi @Smalik , I remember you :) Those SPI patterns are not so good... is your setup working at any Vdd/VddIO? I suspect there is some issue in the SPI communication (2MHz clk is OK), probably not related to the Vdd level itself. Last year you shared t...

Eleon BORLINI · 2023-07-28

Hi @SAbba.1 , for the conversion between LSB (raw data) and physical data for accelerometers, you can refer to the github repository of the C drivers. For example, for the LIS2DW12, you can refer to the file lis2dw12_reg.c: float_t lis2dw12_from_fs2_...

Eleon BORLINI · 2023-06-28

Hi @STLearner , the two part numbers are basically the same device. -Eleon

User statistics

User Activity

* Have a look to the new ISM330IS, the inertial module with embedded ISPU - intelligent sensor processing unit *

* AI/ML Edge Devices and Smart Sensors Integration Master Class*

How to detect the tilt angle of a device with ProfiMEMS tool, IIS2ICLX MLC and Unico

How to perform Asset tracking with the SensorTile.box and Unicleo app

How to detect door opening with the SensorTile.box and the STBLE sensor app

Re: Where i can find the LSM6DS3TR-C naming convention in order to understand the logic under the pa

Re: What's best and way to calculate velocity from acceleration for IIS3DWB and what degree of accur

Re: LIS2DH12 : Not able to communicate with the device when the supply voltage is greater than 2.7V.

Re: How to extract rawdata of sensortile.box . I have received the csV file.. How to understand the

Re: MEMS Microphones frequency response until 20 kHz