About kKim.1

kKim.1 · 2023-08-25

Hello.I have a question about STM32CubeProgrammer.I'm going to use the STM32 system image in Raspberry Pi.How do I flash an STM32 image on an SD card that will be mounted on a Raspberry Pi board?I want to use STM32 program in Windows environment as m...

kKim.1 · 2023-03-21

I found the pin of PG8 on the GPIO pin map on the board. So I connected to PG8 and GND to connect with oscilloscope.In the picture, the blue line is the oscilloscope's GND port.I connected the board and the oscilloscope like the picture above. And I ...

kKim.1 · 2023-03-08

Hello.There is a problem flashing the system image to the board.I use MYD-YA157C-V3 board of Myir company. The board contains a 'MYC-YA157C' CPU, which is based on the STM32MP157 processor (STM32MP157AAC3).I mounted an SD card on this board and attem...

kKim.1 · 2023-02-03

Hello, teachers.I'm sorry in advance because I think I'll be talking too long.The board I use is STM32MP157D-EV1 (evaluation board).From the previous question and answer, I found that Ubuntu 18.04 and SDK could not be installed on my board, which had...

kKim.1 · 2023-02-01

Hello, teachers.First, The board I am using is the STM32MP157D evaluation board.I checked the article that the starter package can be installed in Windowsos, but the developer package and the distribution package are only available in the Linux env...

kKim.1 · 2023-08-27

Hello.Thank you for your answer.I have STM32MP157D-EV1 kit.Then, should I mount the formatted SD card on the STM32 board I have, flash the system image using STM32CubeProgrammer, and then mount the SD card on the Raspberry Pi?

kKim.1 · 2023-03-26

I checked the various documents on the board, and I could find the reason.I tracked the PPS Out pin PG8 (pin 11) in the circuit diagram document on the board and found that it was disconnected. I found 'SB23' in the area where the CPU board is locate...

kKim.1 · 2023-03-09

Hello @PatrickF .Thank you for your response.Let me ask you two more questions.1. Among what you said, does the developer package mean the package provided by ST?2. Should I install a formatted SD card when I flash the eMMC boot image?

kKim.1 · 2023-03-09

.

kKim.1 · 2023-02-02

Hello. @Community member Thank you for your response.I use the USB port of CN16's USB_OTG port. This port has been used to verify that it is connected in Windows OS. And I checked that VMWare-Ubuntu 20.04 is not connecting.I am attaching a picture o...

User statistics

User Activity

How to Flash an STM32 System Image to a Raspberry Pi Board SD Card Using the STM32CubeProgrammer?

I'd like to output the PPS waveform on the STM32MP157D-EV1 board. But it's not outputting.

'STM32MP157AAC3' processor-based MYD-YA157C-V3 board fails to flash eMMC image

Installation and operation of the package on the 'STM32MP157X-Evaluation Board'

On VMWare's Ubuntu 20.04 LTS, the STM32 program tool is not associated with the STM32MP157D evaluation board.

Re: How to Flash an STM32 System Image to a Raspberry Pi Board SD Card Using the STM32CubeProgrammer

Re: I'd like to output the PPS waveform on the STM32MP157D-EV1 board. But it's not outputting.

Re: 'STM32MP157AAC3' processor-based MYD-YA157C-V3 board fails to flash eMMC image

Re: 'STM32MP157AAC3' processor-based MYD-YA157C-V3 board fails to flash eMMC image

Re: On VMWare's Ubuntu 20.04 LTS, the STM32 program tool is not associated with the STM32MP157D evaluation board.