About ZMohd.7

ZMohd.7 · 2022-01-29

Hi, @Community member @TDK I am working on the STM32F4 to implement the FLASH MEMORY CHECKSUM SELF CHECKING to determine if data and program in FLASH have been corrupted and if so not to run the user program.Any information regarding implementation...

ZMohd.7 · 2021-09-07

Hi,I'm facing an issue after configuring the SPI1 of STM32G491REI6 MCU using STm32CubeMX for SPI_DATASIZE_8BIT. I have captured the signals on the Oscilloscope after Transmitting the followed three-byte (0x03, 0x00, 0x50) from master(MCU) to slave. y...

ZMohd.7 · 2020-10-09

Hi, I am working on STM303CBT6 MCU custom design board, USART3 Interrupt callback working fine when program is running in debugging mode.If program running in Normal mode without debugger, USART3 Callback function not calling.Note, MCU BOOT0 pin is c...

ZMohd.7 · 2020-08-25

Hi,I'm working with M24LR Discovery and I would like to Flash demonstration firmware of RF transceiver after erasing flash using STLINK/V2 utility. I am able to erase the Flash but while I'm trying to Flash the .hex or Binary file, following error me...

ZMohd.7 · 2019-03-02

Hi,I'm trying to generate graphical application code from CubeMx_4.26 for using STemWin and GUI Builder tool for target board STM32F746G discovery board.cubeMX .ioc file are attached, It works when I am generating GUI code with extrnal SDRAM use.But ...

ZMohd.7 · 2022-01-21

Hi,@TDK @Chad Livermore Any information will be really helpful. Thanks,Zafar

ZMohd.7 · 2022-01-19

Hi Team,I am Working on STM32F103CBT in my project so I wanted to do simulation for SPI lines.But I am also facing same problem that Sjian has facing.Please provide the scalable solution on these .Thanks and Regards.Zafar.

ZMohd.7 · 2021-09-08

Hi,I am placing two type code snippet I tried-In main routine, NSS is Reset forcefully by firmware (GPIO control), after that "SPI_Transmit" function is called.when you set debugger breakpoint at line4 or line3 of functions, still 2 Bytes sent by the...

ZMohd.7 · 2020-10-26

Hi Pate,After adding 2 second delay before calling NVIC configuration HAL_UART_Receive_IT() in Main function, and it's working fine. HAL_Delay(2000); HAL_UART_Receive_IT(&huart3, Rx_data, 1);Rest code same as above, Hope it will helps.Best Regards,Z...

ZMohd.7 · 2020-10-09

Hi Shivam and Clive,I am facing same issue with STM32F303CBT MCU while program is running in debugging mode using STlink V2, Program working as Intended. each time UART3 Receive interrupt callback function working fine.And when debugger is off and pr...

User statistics

User Activity

STM32F4 FLASH MEMORY CHECKSUM SELF CHECKING

SPI data Issue with SPI_DATASIZE_8BIT

UART Interrupt callback calling only when running in debugging mode using Stlink-V2 Debugger

Firmware of M24LR transceiver board _ Error occured during program operation!

How to generate basic graphical application using STemWin for Target STM32f746G discovery without external SDRAM

Re: stm32F103 ibis model error!

Re: stm32F103 ibis model error!

Re: SPI data Issue with SPI_DATASIZE_8BIT

Re: UART Interrupt callback calling only when running in debugging mode using Stlink-V2 Debugger

Re: UART interrupt not hitting without connecting debugger.