Solved

Hi everybody,I use the STM32CubeProgrammer version 2.3.0Following issue occurs during programming of a hex-file:1.) do a mass-erase or a clear of all sectors of the device2.) read out some bytes (for example the first sector)3.) the device-memory tab shows "00" for every byte (and the whole flash)4.) load a hex-file which has wholes or gaps in the addresses For example like this::020000040800F2 :10000000005000208909000819050008190500089A :180028000000000019050008000000000000000019050008190500084E5.) The new hex-file tab shows that the gap from address 0x0800 0010 till 0x0800 0028 will be filled with 0xFF and not with the processor specific "unused/unprogrammed byte" which has to be 0x00.6.) programming the device and read out the first 40 bytes leads to this screenThe gaps from the hex-file are actually filled with 0xFF which is wrong from my point of view.The old STVP don't fill the address gaps with the wrong initial byte. It fills the gaps with the correct device depending initial f

C:/ST/Motor/STSW-ROBOT-1_R1_LL/EVALKIT_ROBOT_1_SDK543_Positioning_LL/Src/main.c:130: undefined reference to `ModbusRTUTask'orregion `RAM' overflowed by 200 bytes region `FLASH' overflowed by 2912 bytes

HelloThis is my first time soldering a MCU on a custom PCB.As you know, STM32f767 is a very complicated chip and requires Vdd and Vss on many pins. Datasheet also states that capacitors are mandatory on each Vdd or Vref+. However Vref and Vdd (marked on figure) are neighbors and I was wondering if I can use one capacitor for both of them.Could you also tell me if this is a proper way of placing capacitors ? Max distance from Vdd line and cap is 8mm. As you can see, there is only one track and its obviously Vdd line. Of course I am not done with placing all caps and tracking Vdds to pins. I first need to know if this kind of principle is going to work  

Hey folksJust got on populating the passives and ICs on what would appear to be my first ever STM32 based controller (custom PCB). Quite successful and rather impressed with the end result although, perhaps, with the exception of being able to program (ST-Link) while external power is applied (learning harder than I thought lol).Can someone please share a "basic" schematic that would allow for this be achieved. I understand that there are several Discovery board schematics however those shows rather complex circuits with jumpers all over & al. I'm just hoping to see if we have a far better, and "simple/r", approach to that.Any brilliant ideas welcome, that would be kind and helpful. Thanks guys

I am debugging why Ethernet is not working on a setup with stm32f107 + DP83848. Right now I was verifying that the MCO (main clock out) from the stm32f107 is doing what it should by checking with a scope. But MCO output doesn't seem to be working at all, and I can't understand why.The setup: A 25 MHz crystal drives the f107 and is passed to a pll and from that the MCO should output 50 MHz. (Cube is used to set it all up visually.)The f107-PA8 MCO is connected to f107-PA1 (ETH_RMII_REF_CLK) and to DP83848-X1. It's a 4-layer pcb with a proper signal and ground plane between red and blue, with only the vias through it:On my scope I failed to see any signal on the clock output when it runs at 50 MHz. I tried google and this forum, and found something that seemed to indicate that a resistor should be used in series from f107-MCO to dp83848-X1. So I cut off the trace using a knife (under C37). Still no signal. Then I also cut off the trace from f107-PA8 to f107-PA1 (at C20). But even with tr

Hello, We made a board that based on STM32MP157C-DK2. First of all, show the configuration of our board as below.... (1). The major parts and circuit are same as DK2 such as DDR, PMIC, MicroSD, Ethernet. (2). Some parts are removed such as MCU, WIFI/BT, HDMI Tx, USB hub, USB Type-C DRP and LCD module. (3). And add some peripheral such as eMMC, two SPI devices (SPI4, SPI5), EEP (I2C-1) The problem is: The board cannot boot up from SD card, list the symptoms as below... (1). We tried to boot up the board by DK2 SD card (it works well on DK2), but got the exception message from UART ... PANIC at PC : 0x2ffdc323       Exception mode=0x00000016 at: 0x2ffda000 This is all messages since power on. (2). The BOOT cfg. bit setting is confirmed on 101b, boot from SD card. (3). The PA13 (boot status pin) kept Hi or Hi-Z. (4). PMIC RANK-0 no power output, but other RANK had output power. (5). About SD card access....      a. Only SDMMC1_CK, SDMMC1

Back in 2018 this question was posed and I have more information.The answer to this question lays at the bottom of UM1734 where a static allocation code snippet is given.There are two problems with this code snippet that will come back and bite the unwary developer (waves hand):1) the snippet allocates 4 x 32-bit items in an array with no explanation as to how they will be used. Perhaps 4 pointers to 4 USB device descriptors? NO, NOT AT ALL.These 4 x 32-bit values are used to house a 540 byte CDC device descriptor. The various values in memory after this array are then sacrificed to the descriptor.2) Their implementation allocates N x 32-bit values, whereas malloc expects N x 8-bit values, so 3/4 of your allocated space (if you managed to get past issue 1) will never get used. In a memory constrained system. Where every byte could be important.Sigh, now I have to get ahold of my customer and let him know that the 250 units in the field need a firmware update. (insert fornication explet

I'm using two STM32L4xx connected to LoRa modules. The LoRa settings on both cases are:bw = 500 kHzSF = 12CR = 4/5implicit header, Crc off, low data rate optimization is on.On transmitter module, I do the following:Make sure the module is not in sleep modeSet the Tx pin high and Rx pin low.Clear the flagsSet the payload sizeSet the TxBaseAddr and AddPtr to 0x80Write 3 bytes to FiFoChange the operation mode to Transmitter.Wait until the TxDone flag is setI have read back all the registers to make sure they are properly set.On the receive side I make sure the modem is in continuous receive mode and check the flags until RxDone is set to 1. When I check the register RxNbBytes it is 1 and reading through the FiFo I can only see one of the bytes has been transferred.I've been dealing with this problem for about a week now and have tried many different things. Comparing my steps to other libraries (such as mbed os), I'm following the same steps.

I'm trying to use EEPROM emulation API in a project. I have downloaded the expansion package. Based on AN4894 I need core and porting to be included in my project so I copied them under a new directory in Middleware and included the path. Then added the eeprom_emul.h to my project. However stm32l4xx_ll_crc.h is included in the eeprom_emul.h which is not in my project. I activated the crc in cubemx and regenerated the code but this file is missing. Would appreciate any help.

..

Hello,I am trying to use the CR95HF chip in tag detect mode. I am communicating with the chip over UART and am trying to save power by putting the chip into tag detect mode so it will only wake up when a tag is detected.However, in case of a system error I want to have the chip either wake up due to a timeout if it has not detected a tag or be able to wake it up using a low pulse on IRQ_IN.Could you please tell me if waking the chip using a low pulse on IRQ_IN is possible if communicating with the chip over UART? I have set the WU source byte to 0x0A to include tag detection and low pulse on IRQ_IN as wake-up sources but when I do this only the tag detection causes the chip to wake. Full command being sent in this case: 07 0E 0A 21 00 79 01 18 00 20 60 60 64 74 3F 28.If it is impossible to wake the chip using IRQ_IN, then how do I have the chip go into tag detect mode and wake it EITHER when a tag is detected or when the timeout is triggered. In this case I have tried setting the WU so

2 questions here:Is the UART4 connector active by default on the demo board or do I need to build it in?If/when it is active, which STLinux /dev/tty is linked to the I/O path for UART4?thank you,-peter

Hi all,I am using HAL_FLASH_Program() to program an uuid into a specific address. I can verify it write successfully by reading from the address. However, if I power cycle the MCU, the memory at that address returns to the original value. If I write it directly through ST-Link then it stays permanently. Does anyone know why is that? Do I need to erase the memory location before write to it using HAL_FLASH_Program()? I am using STM32F745.Thank you

Hello! Dear ST technician! When I inventory the GB29768 tags , then read tags, In tag memory, read from area:"Could not read tag..." Warning, unable to operate, I used the chip STM32L476 +3993 provided by your company and the original code provided by the official. but the gen2 tag, the above functions can successfully perform read and set operations, so I sincerely consult you here:  Could you tell me what caused it? Looking forward to your reply, thank you vety much!Wish success and happiness!

Hi, I bought new ST25RU3993-EVAL from Digikey. And download en.STSW-ST25RU001.zip on ST web site.ST25RU3993_Reader_Suite software Installed to windows7 PC. Also installed FTDI drivers. When i put USB cable to PC, Red LED is ON. I see new "USB Serial Port(COM16)" on Windows Device Manager.On the first run ST25RU3993_Reader_Suite software, automatically detect new firmware and update device with ST25RU3993_FW_v2-0-0-0_Eval.binThen open again ST25RU3993_Reader_Suite and click "Connect Reader" button. Then Red LED is OFF. And software waiting and locked. No response and no any message. I tested with different PC and Windows10, but result is same. Not working.Why is the software not detecting the board?Thanks.

Hi,Every time i'm trying to open a new project in IDE, after choosing the board and a name for the project i get this "Create minimal project failure: cannot read template source" error messageIs there any solution?screenshot is attached Thanks in advance,Ehud

Here the output of some commands issued on our target at u-boot stage:> STM32MP> mmc list > STM32 SDMMC2: 0 (SD) > STM32 SDMMC2: 1 > > STM32MP> ls mmc 0:4 > <DIR> 1024 . > <DIR> 1024 .. > <DIR> 12288 lost+found > 8192 uboot.env > 6677056 uImage > 71859 stm32mp151a-<myimage>-mx.dtb > 583 boot.scr.uimg > > STM32MP> mmc list > STM32 SDMMC2: 0 (SD) > STM32 SDMMC2: 1 (eMMC)Two questions:why the eMMC is not enumerated before trying to list anything in the SD device?why both are referred to the SDMMC2 bus? I'm expecting the SD card on SDMMC2 and eMMC on SDMMC1... in other words, how to check if the MPU finds the right device when changing the boot dip-switches to eMMC?

Hi,I have working on below setup:Software Tool Chain:STM32CubeMX 5.6.0TouchGFX 4.13.0 DesignerSTM32CubeIDE 1.2.0Hardware:STM32F746G-DISCO (Discovery Board)I have created GUI on TouchGFX 4.13.0. worked fine on simulator and Discovery Board as well.But I am trying import and open project in STM32CubeIDE 1.2.0.Imported Successfully . But Project not successfully compiled. 22:34:33 **** Clean-only build of configuration Release for project STM32F746G_DISCO **** make -j4 clean rm -rf * rm: can't remove 'Middlewares/ST/touchgfx': Directory not empty make: [makefile:151: clean] Error 1 (ignored)   22:34:36 Build Finished. 0 errors, 0 warnings. (took 2s.371ms)   22:34:40 **** Build of configuration Release for project STM32F746G_DISCO **** make -j4 all   In file included from ../TouchGFX/simulator/main.cpp:1:0: ../../Middlewares/ST/touchgfx/framework/include/platform/hal/simulator/sdl2/HALSDL2.hpp:22:10: fatal error: SDL2/SDL_video.h: No such file or directory #include <

Hello Team,I am using System Workbench for coding of STM32f30xx series micro-controller.I m getting some error on regarding St-link match frequency , that is below:-Open On-Chip Debugger 0.10.0+dev-00021-g524e8c8 (2019-04-12-08:48)Licensed under GNU GPL v2For bug reports, read http://openocd.org/doc/doxygen/bugs.htmlsrst_only separate srst_nogate srst_open_drain connect_assert_srstInfo : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWDadapter speed: 8000 kHzadapter_nsrst_delay: 100Info : clock speed 8000 kHzInfo : STLINK v2.1 JTAG v29 API v2 M18 VID 0x0483 PID 0x374BInfo : using stlink api v2Info : Target voltage: 2.915101Info : Unable to match requested speed 8000 kHz, using 4000 kHzInfo : Stlink adapter speed set to 4000 kHzInfo : STM32F303VCTx.cpu: hardware has 6 breakpoints, 4 watchpointsInfo : Listening on port 3333 for gdb connectionstarget halted due to debug-request, current mode: Thread xPSR: 0x01000000 pc: 0x0

I want to take current screen screenshot and save it into JPEG or BMP image file format in mass storage.I have seen saveScreenshot() function, but this is for Simulator.I want to svae screenshot in STM32L4R5.​​​Please comment if you have answers on this.Thank you.​

Hello, I want to generate QR code dynamically and also want to clear it sometimes during run time. I got github link and added those files in my project. Still I am not sure how to call it. You have mentioned to call qrCode.setXY(0,0) , qrCode.setQRCode(&code), qrCode.setScale(4) , add(qrCode) methods but I am unable to find it. https://github.com/touchgfx/touchgfx-open-repository/tree/master/widgets/QRCodeCan you please help ?

Hi All,I am using X-CUBE-CRYPTOLIB for AES ECB encryption/decryption on STM32H7 micro and using the F7 example code and library(libSTM32CryptographicV3.0.0_CM7_GCC_ot.a), provided in the crypto package. But the comparison of encrypted message fails with expected cipher text. FYI i have enabled CRC clock. Please help me out to resolve it quickly. Herewith i have attached the code for your reference

#include <gui/screen1_screen/Screen1View.hpp>   #include "../../Core/Inc/hello.h" // NO in simulator TouchGFX, Yes in CUBEIDEMX extern int myvar; // NO in simulator TouchGFX, Yes in CUBEIDEMX   Screen1View::Screen1View() {   }   void Screen1View::setupScreen() { Screen1ViewBase::setupScreen(); }   void Screen1View::tearDownScreen() { Screen1ViewBase::tearDownScreen(); }   void Screen1View::simpleFunc() { ciao(); // err in simulator TouchGFX myvar = 7; // err in simulator TouchGFX }#include "hello.h"   int myvar = 0;   void ciao(void) { }#ifndef APPLICATION_USER_HELLO_H_ #define APPLICATION_USER_HELLO_H_   #ifdef __cplusplus extern "C" { #endif   void ciao(void);   #ifdef __cplusplus } #endif   #endif /* APPLICATION_USER_HELLO_H_ */#include <gui_generated/screen1_screen/Screen1ViewBase.hpp> #include <touchgfx/Color.hpp> #include "BitmapDatabase.hpp"   Screen1ViewBase::Screen1ViewBase

In the ref man RM0432 Rev 6 the ADC_CCR have used bits in the lower half.In the file stm32l4r5xx.h from stm32cube_fw_l4_v1151 these bits are not defined.They are defined in the files of MCU of the same familly: stm32l4p5xx.hHave I damaged my files?Are the ADCs different between L4R/L4S and L4P ?

Hello.I haven't found similar question. I am beginner with TOUCHGFX: Is it possible to use TOUCHGFX with STM32F0XX series with some cheap TFT Displays? As I read TOUCHGFX supports all of that drivers but I don't understand how to connect all components together. Is it possible?Thank you!