Solved

Hello,I would like to make timer 2 compare event in channel 1 to clock timer 5. Timer 2 compare events also sends DMA request and timer 5 is also used to output a PWM waveform. Here you can find the Init function that I wrote and the main code. At the end something is not working because I can't see any waveform at PAO (the one supposed to output the PWM). I double checked the Timer registers and they seem fine to me. Can you help me in finding the errors? I am not able to undesrtand wheter the problem is on the TIM2 or TIM5 (both the timer synchronization part and the GPIO configuration)I shared only the relvant code for the two timers and removed             // timer2 initialization void TIM2Init (void){ // Enable the timer clock RCC->APB1ENR1 |= (1<<0); // Enable the tim2 clock writing 1 in bit 0 // Set the prescaler and the ARR to set the frequency of the sinewave TIM2 -> PSC = 79; // 80 MHz/80= 1MHz clock --> 1us count TIM2-&g

Hi,I'm using CubeIDE 1.9.0 with X-Cube-TOF1 package 3.0 on a Nucleo-F401RE with VL53L5A1 expansion.I want to create the simple ranging example application with additional crosstalk calibration. I followed the steps from software package user manual UM2974, chapter 4.2.1 to create the application and enabled crosstalk calibration. No other changes are done. The instructions are written for CubeMX, not CubeIDE, but I think I've done it right.But the serial connection always shows sensor init failed. Even disabling crosstalk calibration doesn't show any effect - this setup should reflect exactly the same as the provided pre-compiled binary, I assume.Debugging into the application shows bus acknowledge failure. Also, trying to communicate with the VL53L5 using the ULD driver (not using anything from the TOF1 package) doesn't work reliable, the I2C interface often hangs.There are no modifications to the hardware. I've no idea why nothing from example source codes or Cube packages works out

..

Hello. I have been getting familiar with the STM32L011F4P6 chip. I am using a 20-pin chip soldered onto a board as my test device. I am using a Nucleo-f429zi as the programming/debug device. I have made the necessary changes and am using the SWD header to connect to my chip and program it. The SWD pins on the Nucleo board are connected to the chip for power and reset as well. I am using an arm-none-eabi-gcc toolchain for development with VSCodium. Everything works smoothly, and I use GDB to load the program onto the chip and run/debug with the help of the st-util tool to connect.Now, to my question. I have been trying to reach a 1uA standby mode current consumption, but am stuck at 15uA. This does not even match the documentation's consumption level for sleep mode. I am not using the HAL library, and have been taking a 'bare metal' approach. I am using the stm32cubel0 files (including all the CMSIS) and all seems to be working quite well. I have been reading the datasheet and the user'

Is micro python an option?

Hello dear community,This is my first post here and I am coming to you for help.In the context of a project with a STM32H747I-EVAL board (this board was lent to me and I notice that it doesn't seem to be sold anymore), I need to send/receive CAN messages with another device. I want to use FDCAN1 and FDCAN2.I have created a project with the STM32CubeIDE with the corresponding board. When I go to the "Pinout & Configuration" view, I want to activate FDCAN1 and FDCAN2 but this is where I encounter problems. As the attached screenshots show, I encounter conflicts with other elements when trying to activate FDCAN1 and FDCAN2. These conflicts are present whatever the runtime context (M7 or M4).I admit I am a bit lost and do not know how to continue. Why are these conflicts present? How can I solve them and use FDCAN1 and FDCAN2 ?Waiting for your answer, I thank you for all the help you can give me.Thank you

When I was going through the setup process of USB in STMcubeMX, I suspected that it could not be used as USB host.I would like to know if STM32F372/STM32F373 can be used as USB host. Can STM32F372/373 be used as USB host?

I want to connect a MEMS microphone to my stm32 using its SAI interface. I found a document called "Interfacing PDM digital microphones using STM32 MCUs and MPUs" which gives some examples about how to do it.My question is about the configuration :Why is number of slots equal to 4 ? I dont understand what this parameter represents.In this example, the data size is set to 16 bits and frame length to 64 bits (with free protocol mode).  Sorry if this is a newbie question but why are these two parameters set with different sizes ? I would think that data size should be equal to frame length as I'd want to get all the data sent by my digital microphone. Thanks

I'm trying to get data from PDM microphone and convert it to PCM data. This is my first project on stm32 and I'm starting to debug the project. Could you take a quick look at my code and say if you notice something wrong ? Some part of the code come from other project that have been shared here.#include "main.h"   #include "pdm2pcm_glo.h"   #include "stdio.h"     /* Private variables ---------------------------------------------------------*/   SAI_HandleTypeDef hsai_BlockA1;   DMA_HandleTypeDef hdma_sai1_a;     UART_HandleTypeDef huart1;     PCD_HandleTypeDef hpcd_USB_FS;     /* Private function prototypes -----------------------------------------------*/   void SystemClock_Config(void);   void PeriphCommonClock_Config(void);   static void MX_GPIO_Init(void);   static void MX_USART1_UART_Init(void);   static void MX_DMA_Init(void);   static void MX_USB_PCD_Init(void);   static void

Hi,I tried to run OpenOCD on a virtual machine with Windows Server 2016. We using the version 1.3.0 of the STM32CubeIDE. When I launch the OpenOCD the program crahses with the error message: OpenOCD is launched via this command:CALL %PATH_STLink-OPENOCD%\openocd.exe -f %CD%\ReactionWheelTestFramework_Develop_Master.cfg -s %PATH_SUPPORTFILES% -d4The debug log prints no error and ends like thisInfo : 282 1797 core.c:1394 adapter_init(): clock speed 8000 kHz Debug: 283 1797 openocd.c:142 handle_init_command(): Debug Adapter init complete Debug: 284 1797 command.c:143 script_debug(): command - ocd_command ocd_command type ocd_transport init Debug: 285 1813 command.c:143 script_debug(): command - ocd_transport ocd_transport init Debug: 288 1813 transport.c:239 handle_transport_init(): handle_transport_init Debug: 289 1813 hla_transport.c:152 hl_transport_init(): hl_transport_init Debug: 290 1813 hla_transport.c:169 hl_transport_init(): current transport hla_swd Debug: 291 1828 hla_interface

We are planning to use X-NUCLEO-NFC06A1 eval kit for one of our RFID application that requires read/write range of 30CMs. Can you please confirm the read/write range of NFC06A1 kit? Also, please suggest suitable adhesive RFID tag for this application.

I'm using a stm32wb55RG. I'm trying to get data from a MEMS PDM microphone and convert it into PCM data. I'm using SAI PDM interface and DMA. So far, I think I manage to receive the PDM data (I get some values from the SAI interface) :I don't know if these values make a sense or not. But when I try to convert these data into PCM using PDM_Filter, I can't get any value in the output buffer.I provide the code :#include "main.h" #include "pdm2pcm_glo.h" #include "stdio.h"   /* Private includes ----------------------------------------------------------*/ /* USER CODE BEGIN Includes */   /* USER CODE END Includes */   /* Private typedef -----------------------------------------------------------*/ /* USER CODE BEGIN PTD */   /* USER CODE END PTD */   /* Private define ------------------------------------------------------------*/ /* USER CODE BEGIN PD */ /* USER CODE END PD */   /* Private macro -------------------------------------------------------------*/ /*

Which driver is faster from HAL or LL so cpu can perform other important tasks.​For example to read & write gpio​Using HAL driver,Using LL driver,Using direct access MCU resistor.​

Hello people,I am working on a Project with the stm32wb55 which includes Low Power Modes (Standby) and Bluetooth (BLE).When i turn off the Bluetooth part the controller can simply enter and exit Standbymode by my choice.However if i activate BLE on a Button, work with it and want to enter Standbymode again the controller wont wake up anymore.As i have heard the problem could be something with the cpu2 for example the RF.Is there a way to shut down the cpu2 completely so i can enter the Standbymode like in the first example ?

Throws this incredibly descriptive error:Errors occurred during the build. Errors running builder 'CDT Builder' on project 'App'. java.lang.NullPointerExceptionI tried cleaning and re-importing the project, and the error persists. If I go back to v1.8.0, it works fine. Anyone have a work around for this?

I am trying to carry out a project with a NUCLEO-STM32G431 board.With STM32CubeProgrammer I can program the MCU without problem.But with STLM32CubeIDE I cannot program the flash.STM32CubeIDE 1.8 freshly installed (as I could not achieve anything I reinstalled everything).I create a new project: File / New / STM32 project ...Without touching anything I compile it without problem. Then I try Debug, which creates the debug configuration and runs it.(during the first tests the software of the STLINK-V3 was updated)I get the message:Error in final launch sequence:   Failed to execute MI command: target remote localhost:61234   Error message from debugger back end: localhost:61234: Le système a tenté de joindre un lecteur à un répertoire stocké sur un lecteur joint. Failed to execute MI command: target remote localhost:61234   Error message from debugger back end: localhost:61234: Le système a tenté de joindre un lecteur à un répertoire stocké sur un lecteur joint. localhost:6

I am using the nucleo L476rg and I am not sure to correctly understand the notation in the manual: I want a compare event of a timer to send the DMA request but in the DMA selection register is generally reported TIMx_CHx as request sender.Considering the TIM2 compare event on channel 1. In the DMA requests tab, must I select the TIM_CH1?I am not sure that this means that the compare event sends the DMA request. It is only reported as TIM_CH1....when I have the UPdate it is reported as TIM2_UP and I can easily understand.

..

Hello Everyone,I am trying to establish communication between SPI1 and SPI2 on the STM32F303 Discovery board.I have configured SPI1 as Master and SPI2 as Slave. I am receiving 0xFF when a Receive interrupt is fired in SPI2.SPI1 Master module is configured so: /** * PA4 - NSS PB12 - NSS * PA5 - SCK PB13 - SCK * PA6 - MISO PB15 - M0SI * PA7 - MOSI PB14 - MISO */ __HAL_RCC_SPI1_CLK_ENABLE();   LL_SPI_InitTypeDef SPI1InitStruct;   SPI1InitStruct.BaudRate = LL_SPI_BAUDRATEPRESCALER_DIV4; SPI1InitStruct.ClockPhase = LL_SPI_PHASE_2EDGE; SPI1InitStruct.ClockPolarity = LL_SPI_POLARITY_HIGH; SPI1InitStruct.CRCCalculation = LL_SPI_CRCCALCULATION_DISABLE; SPI1InitStruct.DataWidth = LL_SPI_DATAWIDTH_8BIT; SPI1InitStruct.TransferDirection = LL_SPI_FULL_DUPLEX; SPI1InitStruct.BitOrder = LL_SPI_MSB_FIRST; SPI1InitStruct.Mode = LL_SPI_MODE_MASTER; SPI1InitStruct.NSS = LL_SPI_NSS_HARD_OUTPUT;   LL_SPI_Init(SPI1, &SPI1InitStruct);   LL_SPI_Enable(SPI1);SPI1 GPIO

Hello, I'm using RTC Wakeup to periodically kick WDG while system is in a sleep mode.I have setup RTC wakeup as following:/* RTC init function */ void MX_RTC_Init(void) {   /** Initialize RTC Only */ hrtc.Instance = RTC; hrtc.Init.HourFormat = RTC_HOURFORMAT_24; hrtc.Init.AsynchPrediv = 127; hrtc.Init.SynchPrediv = 255; hrtc.Init.OutPut = RTC_OUTPUT_DISABLE; hrtc.Init.OutPutRemap = RTC_OUTPUT_REMAP_NONE; hrtc.Init.OutPutPolarity = RTC_OUTPUT_POLARITY_HIGH; hrtc.Init.OutPutType = RTC_OUTPUT_TYPE_OPENDRAIN; if (HAL_RTC_Init(&hrtc) != HAL_OK) { Error_Handler(); } }   void HAL_RTC_MspInit(RTC_HandleTypeDef* rtcHandle) {   if(rtcHandle->Instance==RTC) { /* USER CODE BEGIN RTC_MspInit 0 */   /* USER CODE END RTC_MspInit 0 */ /* RTC clock enable */ __HAL_RCC_RTC_ENABLE();   /* RTC interrupt Init */ HAL_NVIC_SetPriority(RTC_WKUP_IRQn, 0, 0); HAL_NVIC_EnableIRQ(RTC_WKUP_IRQn); /* USER CODE BEGIN RTC_MspInit 1 */   /* USER CODE END RT

I noticed that CubeH7 v1.10.0 comes with USB Device library v2.10.0 which supports new class drivers and composite device. However I can't find any document nor examples corresponds to those new features.ST, could you please update USB Device library document to explain new features?BR

..

..

Hi everyone, I'm trying to use the Timer2 CH2 PWM Mode 1 to generate a 1 Hz signal with 50% Duty Cycle out of my PA0 pin but i can't get anything. Here's my code:#include"stm32f3xx.h"   void TIM_PWM(void);   int main(void){ TIM_PWM(); while(1){ } }   void TIM_PWM(void){ RCC->AHBENR |= (1U<<17); //AHBENR GPIOA RCC->APB1ENR |= (1U<<0); //APB1ENR TIM2 GPIOA->MODER |= (1U<<1); //PA0 alternate function GPIOA->AFR[0] |= (1U<<0); //alternate function AF1 on PA0 TIM2->PSC = 8000; TIM2->ARR = 1000; TIM2->CNT = 0; TIM2->CCR2 = 500; //capture compare CH2 TIM2->CCMR1 |= (0b110<<12); //capture compare PWM mode 1 TIM2->CCER |= (1U<<4); //capture compare CH2 output enable TIM2->CR1 = (1U<<0); //counter enable } I'm using a NUCLEO BOARD STM32F303RE. Clock is set to 8 Mhz.Can someone help me? thanks in advance

Hi everyone,I’m working on a custom display board with a STM32H7A3 MCU and a MX66LM1G45G 128Mb OSPI flash. I have build a custom external loader following ST tutorial, with H7 params. I use JTAG to flash.When it comes to use my .stldr custom loader in CubeIDE or CubeProgrammer (v2.7), it fails.Here’s what’s CubeProgrammer says when I try to flash my .bin app (touchgfx project) using the external loader:[…]w ap 0 @0x90000000 0x000D083C bytes Data 0x00000000 // Error: failed to download Segment[1]With CubeIDE using the external loader, it also fails at Segment[1] (see full logs attached)When I try to read a data at 0x90000000 with CubeProgrammer, it also fails (see file log_cubeprogrammer_ReadData.log attached)I have successfully tested my OSPI functions in the main.c of the external loader (writing/reading/erasing) on my board (without the external loader linker modifications). In my TouchGFX applicative project I implemented the same OSPI functions and was also able to read datas in me