Solved

In this package for IDB05A2 https://github.com/STMicroelectronics/x-cube-ble1 In the file Drivers/BSP/X-NUCLEO-IDB0xA1/stm32_bluenrg_ble_dma_lp.h there are few includes :   #include "stm32f4xx_nucleo_bluenrg_dma_lp.h" #include "stm32f4xx_hal_bluenrg_gpio.h" #include "stm32f4xx_hal_bluenrg_spi.h" #include "stm32f4xx_hal_bluenrg_dma.h"  Those files aren't in the Githup repo, where to get them? Should we build them ourselves?

Hello, I'm currently working with a STM32MP157D-DK1 Development Board with 4GB DDR3L. I populated the board with a prebuild openstlinux 6.1 build like discribed in a guide in the ST wiki.When checking the total memory i unfortunatly only get 407MB that are used. root@stm32mp1:~# free --mega total used free shared buff/cache available Mem: 407 138 152 13 140 269 Swap: 0 0 0  Is there a way to use the complete 4GB of RAM? Kind regards,Markus

    Hello, according to my sketchy investigation, passive NFC tags are not required to do FCC, CE certification, because they have no battery and are activated by radio waves emitted by the reader.This conclusion was drawn by unofficial contents.     I also checked official regulations but found no definite terms that exempt passive NFC tags from these certifications.     I am not sure whether ST25DV-I2C integrated product falls into the category of passive NFC tags and needs FCC, CE, TELEC, CC, SRRC certification. The product(framed in red rectangle) can achieve read/write, NFC charging and OTA upgrade to I2C host.Is this product required to do FCC, CE, TELEC, CC, SRRC certification?Thanks!

looking at the size for pool, stack etc , Filex /Azure rtos , its a bit too much :  1024 K - should be : 1024 Byte 

Hello, I followed the tutorial with just one variable (extracted from an elf) there was no problem the variable showed in the chart. But when I added another variable to the code and got a new elf. I went to the variable node to add the new variable but there's none (the first variable also gone). I tried with other elf files from other projects but it doesn't work either. Thank you in advance! (I'm using the CubeMonitor in Window10)

Good day. So I am busy with my final year project, where the goal is to control the speed of a DC motor by reading the armature voltage and current, and then estimating the speed of the motor. I am using the STMCubeMonitor to provide a reference speed, and then the estimated speed is plotted vs the reference speed in the Cube Monitor. I have 1 USB port available on my laptop, therefore I tried using a USB Hub to connect my external mouse and the STM32. When I have this configuration, as soon as a reference speed is entered, the motor does as expected and increases the PWM to reach the desired speed by varyng the voltage, but then the STM disconnects and the monitor stops. I then tried unplugging my mouse, and pluging the STM32 straight into the laptop's USB port. The STM then does not disconnect anymore, but as soon as I set a reference speed, my trackpad stops working and jumps around like crazy and therefore can't enter another reference speed. I have read some issues people are havi

Hello again, I know i posted some time ago but my question is not seen anymore (link to original https://community.st.com/s/question/0D53W00000wWDX2SAO/cubemonitor-still-not-seeing-boolean-values)I was suggested to to include "stdbool.h" but, as I'm working with a C++ project, G++ says that bool is supported and what I get in "stdbool.h" is the following (italic is greyed out code):#ifndef __cplusplus#define bool   _Bool#define true   1#define false   0#else /* __cplusplus *//* Supporting _Bool in C++ is a GCC extension. */#define _Bool   bool#if __cplusplus < 201103L/* Defining these macros in C++98 is a GCC extension. */#define bool   bool#define false   false#define true   true#endif#endif /* __cplusplus */I could manually modify the file to use "C" bool but, is there another way?Thank you!

How to make a chart with a similar functionThe x-axis range is fixed, zooming, etc., the historical waveform is not saved, only the current 10s waveform is displayed

..

..

can stm32cubeMonitor recognize IAR IJet probe?I saw in one of your pages that it should but I tried it with 2 different computers and even though it recognized st-link, it didn't recognize the IJet probe.

I am using the STM32CubeIDE on Fedora linux and I would like to try the STM32CubeMonitor. However only .deb package is available. Is there (or is planned) the release of RPM package?I tried to convert the .deb package using the "alien" utility, unfortunately without success.

Hello,I'm new to STM32CubeMonitor and I need some help. I made a project that consists of sending an unkown length string (DMA) to a nucleo board and then receive the same message on my terminal.I've been using realterm and it works fine, but i would like to know how to send strings using STM32CubeMonitor software.I want to type a message on a 'text input' node, press a button and then send the string to the board.Thank you,Iñigo

Following our STM32CubeMonitor webinar on April 13th, 2021, here are the list of resources and list of Q&A posted as separated answers.Webinar website: https://www.st.com/content/st_com/en/about/events/events.html/stm32-application-monitoring-with-stm32cubemonitor-webinar.htmlWebinar on-demand (watch recording): https://www.st.com/content/st_com/en/premium-content/premium-content-remote-stm32-application-monitoring-with-stm32cubemonitor.html STM32CubeMonitor page: https://www.st.com/en/development-tools/stm32cubemonitor.htmlAttached STM32 demo project and technical slides presented during the demonstration.Below are the questions and their respective answers

Just powered up the  X-NUCLEO-LPM01A with a L432KC mounted in the Nano socket but without having software to cycle thru test modes I have a flat line. In other words, blinky don't cut it for power monitoring.

I plan to show the dashboard via browser to other people, I am afraid they might mess up my flows. Is it possible to add security functionality?I was trying to comment out as per instructions here:https://nodered.org/docs/user-guide/runtime/securing-node-red#editor--admin-api-securitybut the flows will not show after I enabledadminAuth

hello everyone!There are some problems in using snapshot mode.When I switch to snapshot mode, I often can't collect data, as shown in the picture. After a few reboots, the software can work normally. What are the possible reasons?Best regards

..

I have Dell laptop with 4K display (XPS 15).A solution to handle this - to reduce the display resolution to 640x860 by the OS. please use updated JRE which can handle such displays.

I instrumented the code with the supplied code, and it works fine in STM Studio, but when used in CubeMonitor, after started, the dashbord just displays 'Acquisition started, waiting for value'. I've checked the data flow from STLink and found that only 'x' value present in the data payload, but without 'y' value.Is there a way to trigger the data sample manually? Or supporting trigger is mandatory in snapshot mode?

Trying to monitor a 'C' variable of type bool results in the errornot connected ! bad parameter (7)and the probe connection drops. It then comes back all on its own!!Changing the variable to any other type and the monitor runs fine.

Helo, Dear ST!I very happy for use Yours many devices. They are very cool! You are very cool too!So, I was download Your STM32Monitor on my PC. But after install this software on the my Windows 7 I seen unreal picture:Installator of STM32Monitor putted its Icon on the my descktop and after I double clicked it was destroyed and removed all installation files and directories. After, I tryed next two Installs of this software - nothing. All is bad.Please, tell me what I need for repair this problem.With Good wishes,Arthur Tim

I want to in corporate conditional data logging in Cube Monitor Flow, since i intend to monitor the behaviour over many hours.My requirement is to log all the 4 fields:ms_enDeviceOrientationms_stStAccelDataXms_stStAccelDataYms_stStAccelDataZonly if ms_enDeviceOrientation changes from value of 1 to value of 2.I tried to tie this to the trigger threshold in data acquisition but this option was disabled.Could not find any examples to do this any other way.Looking forward to clear and specific description or example.Thanks in advance.

..

After rebuilding an ELF file, going into the Edit Variables node indicates that those variables alphabetically near the top are retained but those further down the list have been dropped requiring them to be re-selected. Is this a memory overflow and is there a way of allocating more memory so this doesn't keep happening?Thanks.