Solved

Hello ST Community!In my use of the STM32N6570-DK I have run several experiments with the kit's tools, and have arrived into some doubts regarding the overall use of the API and the models in the Model Zoo. I have the following questions:Question 1.The Input/Output of my YOLO model is Uint8_t/Float, confirmed by checking the value of the Buffer_DataType_TypeDef element in the network instance, which are both supposed to be stored in a single dimension array as suggested by the API.The output of the model as per the model zoo is (1,4+K,F), with F being proportional to the input image size, in the case of a 256x256x3 image, it's value is 1344.The value of K can be calculated by the maximum size in bytes of the output located in network.h, making the output (1,5,1344), which in a single array would mean, considering output[] as a float array buffer of the output pointer, with values normalized between [0,1]:output[0] = Center Xoutput[1] = Center Youtput[2] = Widthoutput[3] = Heightoutput[

Hi,When transmitting data to the ttySTM0 port, the data goes to the UART4_TX pin connected to the JTAG virtual serial input. However, I need an available TTL serial port to communicate with a microcontroller. How do I enable the USART1 port connected to the PC0/PB0 pins?To which pins is the ttySTM3 port linked? How do I enable it? root@stm32mp1:~# dmesg | grep tty[ 0.000000] Kernel command line: root=PARTUUID=e91c4e10-16e6-4c0e-bd0e-77becf4a3582 rootwait rw console=ttySTM0,115200[ 0.598790] 40010000.serial: ttySTM0 at MMIO 0x40010000 (irq = 61, base_baud = 4000000) is a stm32-usart[ 3.619483] printk: console [ttySTM0] enabled[ 4.294977] 4c001000.serial: ttySTM3 at MMIO 0x4c001000 (irq = 62, base_baud = 4000000) is a stm32-usart[ 4.304256] serial serial0: tty port ttySTM3 registered[ 11.426540] systemd[1]: Created slice Slice /system/getty.[ 11.502583] systemd[1]: Created slice Slice /system/serial-getty.

Hello everyone. I'm currently developing and testing an embedded C software for microcontroller STM32L476 integrated on board ST25R3911B.In order to better understand FTM and its features, I'm trying to use a ST25NFC_Embedded_Lib_ST25R3911B_1.8.0 demo project ( \ST25NFC_Embedded_Lib_ST25R3911B_1.8.0\Projects\STM32L476RG-Nucleo\Applications\X-NUCLEO-NFC05A1 ).Currently I'm facing RX issues on packets over 32 bytes.Down below I attach thw two log outputs (TX = 32 bytes, RX = 32 bytes) and (TX = 96 bytes;  expected RX = 192 bytes)I really don't understand what's messing around here since everything on my traget device is actually working fine.Thank you.

Hi I previously used STM32 VS Code Extension to import cmake project and tried to build and Debug using ST-Link.But due to some update in the extension, the STM32 VS Code Extension got removed and replaced by STM32Cube and now i can't able to debug with existing project. If i click debug still loading and some time it is showing "command: STM32VSCodeExtension.bootFlashBootTarget is not found"Can you tell me how to get back the STM32 VS Code Extension.No STM32 VS Code showing (i installed and used previously).Not showing in Extension browser too. @B_Subramanian @Laurids_PETERSEN  Can you please support in this.

Hello, I am working to implement LwIP onto my MCU (STM32H750VBT6TR) with the PHY (DP83825IRMQR). I got everything set up and was able to do a ping test and create a basic UDP client to send and receive packets (see this thread). This works well on my bare project with just these elements. The issue is that the amount of flash memory taken up by just adding the LwIP peripheral is absurd (it is a combined 110.8 kB out of 128 kB). This leaves little space for the rest of the code this needs to interface with. Looking at tutorials for LwIP implementations show that only around 77 kB is typically used. I am wondering if anyone can help me track down why so much flash memory is being used in my implementation and if it can be minimized? Project files are attached. Thanks in advance.  

Hi everyone,Has anyone interfaced the MX66UW1G45GXDI00 (1Gbit octal SPI Flash) with the STM32N6 XSPI controller?Any working example or experience would help.Thanks!

Does anyone know how to see and set the cacheable status of memory regions in an MP25x series micro? It is very simple for the H755: you pull up the cores in the Cube, and the MPU fields are all there to fill out. The memory regions outlined in the RIF sections for the MP2 do not seem to offer this option. Thanks 

I am working on a project to connect QSPI flash memory to a PC as a USB mass storage device (MSC) using USBX, FILEX, LVLX, and THREADX on an STM32. This setup should allow the QSPI flash to appear as a drive in Windows.Previously, I successfully implemented a similar project using the MCU's internal RAM as the storage medium. However, after switching to QSPI flash, I encounter the error message: 'Please insert a disk into USB Drive' when connecting the device to a PC.To debug this issue, I tested the QSPI flash read/write functionality using FILEX + LVLX + THREADX without USBX, and it worked perfectly. This suggests the problem lies in the integration with USB MSC.I am including my code for review. Could anyone help identify any potential errors or missing steps in my implementation? Additionally, are there specific areas I should focus on to resolve this issue? Thank you.EDIT :lastlba ux_device_msc.c

Hello,I am trying to set up FileX with USBX, but my computer recognizes a disk drive but does not see any volume.Can you help me determine whether I am using the fx_media_format and fx_media_open functions correctly, given that they do not return any errors?  UINT ret = FX_SUCCESS; /* USER CODE BEGIN MX_FileX_Init */ UINT RETT = lx_stm32_nor_custom_driver_initialize(&nor_flash); /* USER CODE END MX_FileX_Init */ /* Initialize FileX. */ fx_system_initialize(); /* USER CODE BEGIN MX_FileX_Init 1*/ /* Format the NOR flash as FAT */ status = fx_media_format(&nor_flash_disk, fx_stm32_levelx_nor_driver, // Driver entry (VOID*)&nor_flash, // Device info pointer (VOID*)NOR_CUSTOM_DRIVER_ID (UCHAR*)media_memory, // Media buffer pointer sizeof(media_memory), // Media buffer size "NOR_FLASH_DISK", // Volume Name 1, // Number of FATs 32, // Directory Entries 0, // Hidden sectors TOTAL_SECTOR_LOGICAL, // Total sectors SECTOR_SIZE

Hi all，I now use ST25R3920B as a card reader on the official nucleo nfc08A1 of ST to read cards. However, I found that when the card was detected by 3920B, the current increased to 300mA, but the maximum current borne by PCB was 350mA.Can I reduce the current and how should I operate the configuration software code? 

Need help identifying the material of semiconductor SOA (safe operating area) for STPS3L40UF. Which material below? Silicon Silicon Carbide Gallium Nitride Other

So Im trying to move heap to my external SDRAM and the problem is that it hardfaults after 3s and do not know why.In startup file before__libc_init_array i call fmc function which init SDRAM.Fmc function looks like this:  void fmc(void) { HAL_Init(); SystemClock_Config(); PeriphCommonClock_Config(); MX_GPIO_Init(); MX_FMC_Init(); MPU_Config(); // mark SDRAM cacheable SCB_EnableICache(); SCB_EnableDCache(); } Im using TouchGFX, STM32H743ZIT6 and IS42S16400J-6TLI SDRAM. Ive already changed my sbrk, linker and MPU. I add code fragments: /* ****************************************************************************** ** ** File : LinkerScript.ld ** ** Author : STM32CubeIDE ** ** Abstract : Linker script for STM32H7 series ** 2048Kbytes FLASH and 1056Kbytes RAM ** ** Set heap size, stack size and stack location according ** to application requirements. ** ** Set memory bank area and size if external memory is used. ** ** Target : STMicroelectronics STM32 ** ** Distributio

Hello,I'm working with B-WL5M-SUBG1 hardware for experiencing STM32WL5MOCH6U. I ran the application from Repository\STM32Cube_FW_WL_V1.3.1\Projects\B-WL5M-SUBG1\Applications\SigfoxI got current of about 2.3mA in standby mode instead of  less than 1uA as specified in the datasheet and I discovered that the 5V_PWR LED(LD4 Green) was ON.I broke the SB14 to prevent the 5V_PWR LED from turning on: Current down to 900uA-950uA band with this move.After that I applied this post's recommendations. Current down to 875uA-810uA band. But I unfortinatelly I'm still far away from 1uA. Anyone has soluion?

Hello ST Brightsense Team,Would like to know if the VD66GY Linux driver (STSW-IMG503_V4L2) will work on an NXP IMX8M Mini (no hardware ISP) ?  If not will it work with the IMX8M Mini Plus (with Hardware ISP).Currently using the STEVAL-66GYMAI.In the STSW-IMG503_V4L2 package, the provided driver / device tree seems for the Raspberry PI, what would be the required changes for that to work on NXP IMX8 platform ? Is the vd56g3.json ISP tuning file required ( no libcamera installed, only using Gstreamer)... Thank you.

So I am reading the RM0008 Reference manual because I need to describe some limits for my systemI am looking for the UARTs tolerance of clock drifton page 800 I am confused by these tables: In my case DIV_FRACTION is different from 0 and the M bit is 0The way I read the table... the Noise Flag triggers as an error if there is more than 3.33% clock drift...but... it does not care if there is 3.88%...This makes no sense so... am I misunderstanding something  or?Link to the document in question:https://www.st.com/resource/en/reference_manual/rm0008-stm32f101xx-stm32f102xx-stm32f103xx-stm32f105xx-and-stm32f107xx-advanced-armbased-32bit-mcus-stmicroelectronics.pdf

Hi,I am try to STM32WBAG-DK1 PBP source example and try to create multi-channel and stream the data through it. Like in each channel, each language. I got stuck where to modify the code.Could anyone please support the issue. Thank you

Follow-on from: Help for porting from MDK to CubeIDE.HiI am now working on porting an MDK example to CubeIDE on an F767-based customized board with 32MB SDRAM and an LCD interface.At the moment, the build of the ported example in CubeIDE gives following erorr message:The following is the original code of the example targeting on ARM compiler:static __align(64) uint8_t mem1base[160*1024]; static __align(64) uint8_t mem2base[28912*1024] __attribute__((at(0XC01F4000))); static __align(64) uint8_t mem3base[60*1024] __attribute__((at(0X20000000))); static uint32_t mem1mapbase[160*1024/64]; static uint32_t mem2mapbase[28912*1024/64] __attribute__((at(0XC01F4000 + 28912*1024))); static uint32_t mem3mapbase[60*1024/64] __attribute__((at(0X20000000 + 60*1024))); Now after the porting, the code is changed to:/* mem1 (internal RAM) (64 bytes alignment) */ __attribute__((section(".mem1base.mem1_base"))) static uint8_t mem1base[160 * 1024] = { 0 }; // mem2 (32MB external SDRAM) // 64 byt

So, I'm trying to increase my ENOB from 13.7 bits to 16 bits or higher through the hardware Oversampling system, if possible:MCU: STM32H750V1) If I increase the Oversampler ratio to 128 or 256 without any bit shift, do I get the increased ENOB?2) My application does not need the absolute accuracy, only precision(or resolution), and low noise. How can I increase the ADC bits to 17 or 18 bits, and receive 18-bit data in my memory buffer?I use 16-bit DMA transfers into a 16-bit Memory buffer, and everything works. Then, as soon as I change the DMA and buffer size to 32 bits to receive higher bits, I get very large and wrong values, what would be the culprit? I'm out of the Application Notes and Reference Manual to read, and I couldn't see a clear explanation of how to do bit shifting or achieve higher than 16-bit resolutions..And the Fact that I'm a bit of a noob doesn't have to do anything with it of course.Any help would be appreciated.

Hello,I have custom board with STM32N6. I followed guidelines how to enable the ITM console:https://community.st.com/t5/stm32-mcus/using-the-itm-console-for-printf-redirects-and-lwip-debug/ta-p/723472The System Core Clock is set to 600MHz, confirmed with variable SystemCoreClock=600. The Trace Anynchronus Sw is selected and PB3 connected.Simple ITM_SendChar(101); gets executed but no output in the console. I tried 600MHz core clock for the Serial Wire Viewer, also many other clock frequencies like 75MHz (TPIU clock), but none is working.Are there any special steps to configure ITM console on STM32N6?

Post edited by ST moderator to be inline with the community rules especially with the code sharing. In next time please use </> button to paste your code. Please read this post: How to insert source code I have a custom board using an STM32H735VGT6 MCU, and I’m trying to configure it to run at different system frequencies, starting from the lowest (170 MHz) and eventually up to the maximum (520 MHz or 550 MHz). I’m using an external 8 MHz crystal as the clock source. My plan is to start at 170 MHz using VOS3 mode (since it supports up to 170 MHz) and later switch to higher VOS levels (VOS2, VOS1, VOS0) for higher frequencies. To check whether the MCU is running at the desired frequency, I set up a timer and assign the timer counter value to a variable to monitor in STM32CubeMonitor, basically to see how many counts per second I get. Here’s the code: /* USER CODE BEGIN Header */ /** ****************************************************************************** * @file

Hello, I would like to know if this PTP client example from Netxduo can be used on an STM32H723 MCU: https://github.com/eclipse-threadx/rtos-docs/blob/main/rtos-docs/netx-duo/netx-duo-ptp-client/chapter1.md Another MCU, the STM32N6 has this implementation here: https://github.com/STMicroelectronics/STM32CubeN6/tree/main/Projects/NUCLEO-N657X0-Q/Applications/NetXDuo/Nx_PTP_Client I wanted to confirm if the STM32H723 does support that example because i am looking at https://github.com/STMicroelectronics/x-cube-azrtos-h7/tree/main/Projects and I cannot find any ... Thank you.

Hello,   I am having a hard time finding which software pack this file vl53l8cx_def.h is in? I think once I get that I should be get the zones if Im understanding the error correctly. Please advise.  If it helps with the solution I am trying to use the P-NUCLEO-53L8A1 and VL53L8CHV0GC to generate 3D point clouds.            

I need to cut off all the power supplys of VL53L8 to save power. Does the firmware need to be re-downloaded every time the device is powered on? loading firmware is in the function uint8_t vl53lmz_init( VL53LMZ_Configuration *p_dev)​

Hi, I have a STM32N6570-DK and I see that the available demo code is up to v1.3.0How do I determine what version of code was shipped on the DK?Is there a document that details how to upgrade the code if it’s needed?STM32N6-OOBSTM32N6570-DK Out-of-the-box demo binary1.3.0Thanks, Tony 

 Hi everyone,I'm working on an STM32 project using STM32CubeIDE. I'm using the built-in debugger with ST-LINK and UART (via HTerm) to monitor communication between the STM32 and a host PC.Here's something odd I noticed:When I click the "Debug" button in STM32CubeIDE (but before I press "Resume"), I already see some UART output in HTerm, like:AA 00 40 02 00 00 4D 55AA 00 50 02 00 00 2A 55Then, when I press "Resume", the same two messages are sent again. So in total I see them twice.This seems strange because I wouldn't expect the UART to be transmitting anything before the code is running (i.e., before Resume is hit). But clearly, something is happening during the debugger halt or initialization phase.Is this normal?Is it common for STM32CubeIDE to somehow "pre-run" some initialization code before Resume?Could it be something about HAL_UART_Transmit being called from main() before HAL_Init() fully returns?Or maybe the ST-LINK somehow triggers this?The program runs fine otherwise, b