Solved

Posted on July 20, 2016 at 09:43Hi, in the last time I played with the power modes of the STM32L0 and discovered an issue with the GPIO-HAL driver. The used version of the HAL is 1.7.0 with a STM32L053 nucleo board. I discovered that the initialization of USART-TX and -RX pins will increase the power consumption in STOP mode considerably. So I tried to deinitialize the pins to their reset state with the function HAL_GPIO_DeInit() before going into STOP mode. But the consumption remains the same so I looked into the DeInit-function and recognized the line where the I/O mode is changed (line 327 in stm32l0xx_hal_gpio.c):GPIOx->MODER &= ~(GPIO_MODER_MODE0 << (position * 2U)); The I/O mode is changed to ''input'' but the reference manual for the controller (RM0367) says in chapter 9.4.1 that the reset state for the I/O mode is ''Analog'' . According to this I changed the line 327 toGPIOx->MODER |= (GPIO_MODER_MODE0 << (position * 2U)); and the power consumption get

Posted on January 19, 2017 at 13:20Hi,I have this SMD component that I cannot identify:Package size: SMCMarking from top:<STMicroelectronics logo> (e3) GFBR GP 611I have no idea what this can be, and by the way, is there any place or list where one can search by STMicroelectronics markings?

Posted on January 06, 2017 at 09:59Hi Master G ;-),can you explain the error 'Init not performed (time-waited connections)'? I don't find anything about this in the documentation.I get the error when:1. Close the ports: AT+S.SOCKD=02. Do some web things: AT+S.SOCKON=example.com....3. Close the sockets... AT+S.SOCKC==004. Open the port again: AT+S.SOCKD=33000If I try to open the port some seconds later I don't get the error any more...Thx & Regards,Flow

Posted on January 18, 2017 at 05:44Hello folks,I am working to migrate my firmware from stm32f103 to stm32f20f family, for that I have gone through the guide provide by st http://www.st.com/content/ccc/resource/technical/document/application_note/27/7b/1b/45/e7/ac/4e/04/DM00033267.pdf/files/DM00033267.pdf/jcr:content/translations/en.DM00033267.pdf.Now my firmware includes spi (in master mode), GPIOs(in irq), Systick(configured in micros) all these are woking very well in stm32f1 and i am getting my desired output on tis MCU but when I migrated GPIOs(irq), SPI (tx irq), Systick works as expected but tough I am not getting my out put on spi slave device.Here my slave device is 1.44 '' TFT LCD.I am using Hal Library here.For testing I did LED blinking it worked i also did uart but uart is also not working.It seems like its something related to clocks.I have configured my clocks on HSE 8 MHZ.Requested to guide me here.Also please let me know if i can provide any more details.Thanks &

Posted on January 17, 2017 at 14:59Hi, I want to use the STM32F413 SRAM2 to run interrupt control loop routines, as I do for CCM-SRAM of the STM32F303. So I need to configure the SRAM2 to be acessed through the I-Code/D-Code bus (address 0x10000000) to burst the performance.I didn't figure out how to do it reading the reference manual. SRAM2 can be acessed at the address 0x20040000 or at the address 0x10000000, or I need to to some register configuration to change de SRAM2 address from 0x20040000 to 0x10000000?Can I use the procedure to run an Interrupt routine at STM32F303 CCM-RAM for the F413 SRAM2?Ari.

Posted on January 11, 2017 at 05:32hi i am new to linux,.this is my first time to use command line makefile to compile.i now encounter a problem that undefined reference to `AccHw_RSA_PKCS1v15_Encrypt' in the /Examples_Crypto/Src/example_rsa_encdec.cbut i have already added the library path and library for thatLFLAGS += -L$(TOPDIR)Middlewares/ST/STM32_Crypto_AccHw/Lib -lSTM32AccHwCryptoV3.1.0_F2_GCC -lSTM32AccHwCryptoV3.1.0_F2_GCC_ot -lmmain.elf: $(OBJS) $(CC) $(LFLAGS) -o $@ $(OBJS) @echo 'linked '$<'!\n'I would appreicate if anyone can help.ThanksJeff

Posted on January 16, 2017 at 22:19Subject says it all. I'd like to see what's changed/new before I upgrade.Thanks!

Posted on January 16, 2017 at 20:44The original post was too long to process during our migration. Please click on the attachment to read the original post.

Posted on January 16, 2017 at 11:41 Good Day I have an oscillator connected to Comparator 1, I want the output of Comparator 1 to internally go to timer 2. I would like to manually start TIM2, leave it for a few milliseconds, and come back and read how many times the comparator changed state. I then want to reset the value back to zero and it must start counting up again, one count for every transition of the from high to low on the comparator. How must I set up timer 2 to achieve this? I have it set-up as Slave Mode with External Input but I think it is incorrect. I have set Comparator 1 as follows: void MX_COMP1_Init(void){ hcomp1.Instance = COMP1; hcomp1.Init.InvertingInput = COMP_INVERTINGINPUT_IO1; hcomp1.Init.NonInvertingInput = COMP_NONINVERTINGINPUT_IO1; hcomp1.Init.Output = COMP_OUTPUT_TIM2IC4; hcomp1.Init.OutputPol = COMP_OUTPUTPOL_NONINVERTED; hcomp1.Init.Hysteresis = COMP_HYSTERESIS_LOW; hcomp1.Init.Mode = COMP_MODE_HIGHSPEED; hcomp1.Init.WindowMode = CO

Posted on January 16, 2017 at 11:36Subject: CubeMX 4.19: Nucleo-F4 Board Selection?Hi there,01-16-2017I have CubeMX 4.19 installed with these 'FW' for  STM 32L1 & 32F4 processors:- STM32Cube_FW_L1_V1.6.0- STM32Cube_FW_F4_V1.14.0My target: STM32 Nucleo-F401RE board that I am using to learn the STM series processors and libs, programming strategies. However, there is no board selection for any 'Nucleo F4' boards in the v4.19 CubeMX, yet there are board selections available for STM 32F4 'Discovery' boards as can be seen in the two screen captures below.CubeMX v4.19 Missing Nucleo-F4 Board Selection ProblemCubeMX v4.19 32F4 'Discovery' Board Selections are availableOn the STM website, I find that there are only three F4 Nucleo boards being offered:NUCLEO-F401RENUCLEO-F410RBNUCLEO-F411REWhile it is true that I can likely kluge together a work-around project, I am using my Nucleo-F401RE board's Morpho-connectors (neato-feature) in a project, I wire-wrapped the prototype. So it woul

Posted on January 16, 2017 at 14:29Hello,we use the STM32L051C8 MCU and include the stm32l051xx.h in version 1.7.0. (31-May-2016). We can't find any definition for timer7 peripheral. Is there a reason why it's missing? are we using the wrong header file?Thanks in advance for a short response!T.Rohde

Posted on September 28, 2016 at 10:11I'm using STM32F301C8microcontroller in my project. I use STM32Cube for init code generation.In ADC init part i configured injected channels to be externallytriggered from TIM2. After code generation i tried to build the project in IAR but i got an error:Error[Pe020]: identifier ''ADC_EXTERNALTRIGINJECCONV_T2_TRGO'' is undefined...Isit caused from a STM32Cube error or doesn't STM32F301C8microcontrollers ADCs injected channels have a feature of beingexternally triggered from TIM2.Regards;Omer  #stm32cube

Posted on January 16, 2017 at 09:52https://my.st.com/content/my_st_com/en/products/embedded-software/mcus-embedded-software/stm32-embedded-software/stm32-standard-peripheral-libraries-expansions/stsw-stm32066.license%3d1484550263426.html I am able to find the Eeprom emulation software on STM32F4xx devices.But it is based on Standard Peripheral Library. I am looking for HAL based driver or example.Some threads that I came across on forum did not explain clearly, please elaborate.#stm32f4 #stm32cube #hal-eeprom-emulation

Posted on January 13, 2017 at 14:51 edit: previously I wrote that problems occurs with freertos, I checked without it and I am having the same problem (ending in dead loop after sending more than 8 characters). Steps to reproduce: Create project in CubeMX for STM32F4DISCOVERY, enable USB_FS Device only. Configure clock: PLL_N = 72, PLL_Q=3, that gives me 48 MHz for usb, other settings remain unchanged. In configuration I enable CDC device with default parameters. Generate code for SW. I add some led toggle in order to know it it is running. /* StartDefaultTask function */ void StartDefaultTask(void const * argument) { /* init code for USB_DEVICE */ MX_USB_DEVICE_Init(); /* USER CODE BEGIN 5 */ /* Infinite loop */ for(;;) { HAL_GPIO_TogglePin(LD3_GPIO_Port, LD3_Pin); osDelay(500); } /* USER CODE END 5 */ }�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�?�? In file usbd_cdc_if.c I am setting breakpoint at CDC_Receive_FS funct

Posted on January 15, 2017 at 21:27I am working with a Nucleo L031K6 board and my application showed strange behaviour that I could finally track down as two C variables sharing the same memory location....Not being a specialist in neither C nor the ST family, my question is: What am I doing wrong? or is this a bug in the compiler?Below my stripped C source and the disassembly listing from the debugging session. Of course this application does not do anything at all anymore, but it still demonstrates the fault.The variable 'secs' shares his address with variable 'txt[1][0]'/* Includes ------------------------------------------------------------------*/&sharpinclude 'main.h'&sharpinclude 'stm32l0xx_hal.h' int32_t tel; uint32_t Klokstat; uint8_t txt[1][5];uint8_t secs;/* Private function prototypes -----------------------------------------------*/void Error_Handler(void);int main(void){  /* Reset of all peripherals, Initializes the Flash interface and the Sys

Posted on December 10, 2016 at 22:07I am testing the microSD card. The weird thing is that it works well in debug mode, but doesn't work in normal mode.I set the breakpoint to a line at the very end in debug mode, before which the operation of microSD card is done. In debug mode, it works very well. But when I quit the debug mode, the sd card doesn't work. I am using keil, uvision as the IDE. The chip is STM32F405RGT6;What should I do?

Posted on January 12, 2017 at 22:36Where can one find the current version of stm32f437xx.h?Thanks,jh

Posted on January 13, 2017 at 13:50Hello,I have a funny question. I have STM32F401RBT6 and my firmware is ~140KB in size. I can download it without any issues, but the datasheet for this chip says that it should have only 128KB of Flash?Also when I query the ID_FLASH_ADDRESS register it returns 128.The code downloads and verifies properly.Also when I use the ST Link utility, and modify bytes in Flash between 128KB and 256KB they are stored correclty. I'm confused by this. Does this chip has 256KB of Flash or not?Thank you,

Posted on January 06, 2017 at 12:37Hello ST,it seems that the escape_seq parameter does not work as expected in the IDW01M1.There are some discrepancies between the user manual and the obtained results. Please have a look at my transcript:12:16:15.761 [TX] - at+s.scfg=escape_seq,at+miao<CR>12:16:26.101 [RX] - OK+WIND:61:Incoming Socket Client:192.168.0.218+WIND:60:Now in Data Mode12:25:49.307 [TX] - at+miao12:25:49.807 [RX] - +WIND:59:Back to Command Mode12:26:05.899 [TX] - at+miao12:26:10.363 [TX] - at+miao<CR>12:26:10.595 [RX] - ERROR: Command not found12:26:13.700 [TX] - AT+S.<CR>12:26:13.703 [RX] - +WIND:60:Now in Data ModeSo, it seems that:1) escape_seq only changes the data->command sequence, but not the command->data2) when in command mode, you need to send a to activate the sequence, despite the fact that the manual states the opposite.Some more information:♯ nv_model = SPWF01SA1♯ nv_serial = 3915D31697♯ version = 160129-c5bf5ce-SPWF01SGiuseppe#x-nucleo

Posted on December 21, 2016 at 05:41Hi,I(or may be ST) have a ptoblem. I tried to use ADC1 & ADC2 in regular dual mode with DMA on STM32F103C8T6 MCU(startup code generated by last CubeMX). If I configure ADCs in continues mode, then start ADC2(using HAL_ADC_Start()) and then start ADC1(using HAL_ADCEx_MultiModeStart_DMA()) all works fine. But it is too fast collect data.I remove continues bit from ADCs in my code:MODIFY_REG(hadc2.Instance->CR2, ADC_CR2_CONT, ADC_CR2_CONTINUOUS(DISABLE));MODIFY_REG(hadc1.Instance->CR2, ADC_CR2_CONT, ADC_CR2_CONTINUOUS(DISABLE));and start them again. In timer interrupt I trigger ADC1:SET_BIT(hadc1.Instance->CR2, (ADC_CR2_SWSTART | ADC_CR2_EXTTRIG));And happens something strange: all looks fine, DMA collect data but data from ADC2 is invalid. Looks like it same data as in first conversion after start ADCs. I found, that if I will set ADC_CR2_EXTTRIG flag for ADC2 before triggering ADC1 all works fine:SET_BIT(hadc2.Instance->CR2, ADC_CR2_E

Posted on July 15, 2016 at 14:35Hi All,I'm using STM32L475, STM32CubeMX 4.15.1, STM32L4 firmware library 1.5.1 and the code generated by STM32CubeMX. When initializing ADC1 and ADC2 the ADC2 initialization, MX_ADC2_Init(), sometimes calls ErrorHandler() because HAL_ADCEx_MultiModeConfigChannel() is returning and error.HAL_ADCEx_MultiModeConfigChannel(), stm32l4xx_hal_adc_ex.c, is called with hadc->Instance = ADC2; therefore, ADC_MULTI_SLAVE(hadc, &tmphadcSlave) sets tmphadcSlave->Instance = NULL. When ADC_IS_CONVERSION_ONGOING_REGULAR(&tmphadcSlave) is called a NULL pointer, tmphadcSlave->Instance->CR, is dereferenced and leads to unexpected results.The NULL pointer deference can be fixed by changing macro ADC_IS_CONVERSION_ONGOING_REGULAR, stm32l4xx_hal_adc.h, to#define ADC_IS_CONVERSION_ONGOING_REGULAR(__HANDLE__)                                         \  &nb

Posted on August 03, 2016 at 15:14Hello! I am trying to start ADC2 on stm32l476, but it always goes to error handler multimode.Mode = ADC_MODE_INDEPENDENT;     if (HAL_ADCEx_MultiModeConfigChannel(&hadc2, &multimode) != HAL_OK)     {     Error_Handler();     } This condition never return true if ( (ADC_IS_CONVERSION_ONGOING_REGULAR(hadc) == RESET)     && (ADC_IS_CONVERSION_ONGOING_REGULAR(&tmphadcSlave) == RESET) ) I checked bits in registers but they are ok. Can you tell me thats wrong?

Posted on November 04, 2016 at 05:47The original post was too long to process during our migration. Please click on the attachment to read the original post.

Posted on October 24, 2016 at 03:17 I'm working with STM32L476 trying to get a microSD card to communicate. Initially I'm sure I was getting a response, but now when I send CMD8 the chip does not see a respons from the card (SD_CMD_RSP_TIMEOUT). Even though the signal is present on D0. Here is clock setup, initially clock runs at ~300kHz for setup. /** System Clock Configuration */ void SystemClock_Config( void ) { RCC_OscInitTypeDef RCC_OscInitStruct; RCC_ClkInitTypeDef RCC_ClkInitStruct; RCC_PeriphCLKInitTypeDef PeriphClkInit; RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_MSI; RCC_OscInitStruct.LSEState = RCC_LSE_ON; //Low speed external crystal RCC_OscInitStruct.MSIState = RCC_MSI_ON; //Mid speed internal osc RCC_OscInitStruct.MSICalibrationValue = RCC_MSICALIBRATION_DEFAULT; RCC_OscInitStruct.MSIClockRange = RCC_MSIRANGE_6; RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_MSI; RCC_OscInitStr

Posted on January 12, 2017 at 21:10This CRC is used by an I2C peripheral and documented at http://www.sensirion.co.jp/fileadmin/user_upload/customers/sensirion/Dokumente/GasFlow/Sensirion_Gas_Flow_SFM3000_CRC_Checksum.pdf  Can this CRC be duplicated using the CRC IP on the STM32F7? The HAL library defaults to X^4 + X^2 + X^1 and I seem unable to change that (and it states that the exponents must be less than 8.) I tried substituting the code for the polynomial above (0x131) and the HAL initialization code rejected it.Is this a shortcoming of the library or a limit of the H/W?Code to init the CRC produced by Cube is:/* CRC init function */static void MX_CRC_Init(void){hcrc.Instance = CRC; hcrc.Init.DefaultPolynomialUse = DEFAULT_POLYNOMIAL_DISABLE; hcrc.Init.DefaultInitValueUse = DEFAULT_INIT_VALUE_DISABLE; hcrc.Init.GeneratingPolynomial = 0x7; hcrc.Init.CRCLength = CRC_POLYLENGTH_8B; hcrc.Init.InitValue = 65535; hcrc.Init.InputDataInversionMode = CRC_INPUTDATA_INVERSION