About blechleitner

blechleitner · 2024-01-22

Hi everyone,we have taken over the further development and support of a board containing a STM32F407. The board contains a USB port, connected to PA11/PA12, Reset and BOOT0 are connected to push-buttons. So a firmware upgrade by means of the STM32Cub...

blechleitner · 2020-07-09

Hi,I have the following setup running:Windows 10 (latest), STM32CubeIDE 1.3.1, local GDB Server and ST-LinkV2. Debugger settings are default. The project is CubeMX generated.I did a search on the ST site as well as Google but didn't find anything. So...

blechleitner · 2016-07-01

Posted on July 01, 2016 at 12:30Dear ST Team, along another issue I found in the F373 SDADC code, I saw a strange behaviour of the SDADC against the description in the F373 reference manual. My software samples some sensors connected to multiple cha...

blechleitner · 2016-07-01

Posted on July 01, 2016 at 12:13Dear Guys, im working on an project where I have to sample 4 sensors which are connected to two SDADC's, two on each. The system is triggered by timer 19 and makes continuous conversions into a memory buffer by means ...

blechleitner · 2015-11-15

Posted on November 15, 2015 at 16:31Hi, when CubeMX generates code, it is intended by 2 spaces. Ist there the possibility to change this behaviour to get a tab character instead. I searched in the forum and googled for a while but unfortunately, I d...

blechleitner · 2021-05-07

Hi,@ S C:I did now some tests but I am not happy with the new version. Until today, I used CubeIDE 1.6.1 with STLinkUpgrade 3.3.5 and STLink Fiwmware V3J7M3. Everything worked so far except the mass storage issue. I integrated the new Upgrade Tool an...

blechleitner · 2021-05-07

Hi,thanks a lot. I downloaded the file and pushed it to a test system. Went like a charm. Now I will do the necessary tests but it looks very promising.Best regards,Bernhard

blechleitner · 2021-05-06

BUMP!Hi dear,are there any news about that story? In 1.6.1, there is still no solution. It's now 8 month passed since the reply from a ST employee, telling us that a solution is in the queue. Maybe the member S C can check this again and give us some...

blechleitner · 2021-03-10

Hi,even it is a quite old thread I am reusing here because today, I walked into the same trap. I am using CubeIDE 1.6.0 (the latest one) and it runs on a Windows 10 system with all updates. Everything went ok until I installed PyDev today. So far the...

blechleitner · 2021-01-11

Hi,while searching, I found this question and would like to ask about the actual state of this issue.I have a similar issue with the STLINK-V3MINI. I am using the latest firmware update tool 3.3.4 within CubeIDE 1.5.1 and there is no choice of modes ...

User statistics

User Activity

STM32 field firmware upgrade with "CubeProgrammer Light"

STM32CubeIDE 1.3.1 Debug session does not start when 'Build before launch' unchecked

STM32F373 SDADC injected conversion order

STM32CubeMX generated code for STM32F373 SDADC buggy

STM32CubeMX Source code format

Re: STLINK V3 - without mass storage enabled.

Re: STLINK V3 - without mass storage enabled.

Re: STLINK V3 - without mass storage enabled.

Re: Debugger wont launch

Re: STLINK V3 - without mass storage enabled.